oo. I was looking for
> installation instructions and would be interested to hear how it goes for
> you.
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
>
>
> On Thu, Aug 15, 2019, 2:54 PM J.R. Farrar via CnC-List <
> cnc-list@cnc-list.com&g
Sucked up a snake of seaweed into the seacock and hose once. Had to remove
the line between the seacock and strainer to get everything out as it was
snaked in there pretty good. Once I got the hose off and seacock cleaned I
just closed it. Hooked everything back up and opened it again. BTW just
I have two 1/2"
On Thu, Jun 28, 2018, 09:29 Neil E. Andersen via CnC-List <
cnc-list@cnc-list.com> wrote:
> What size tubing do you use from the mast step plate to the bilge?
>
>
>
> Neil
>
> 1982 C&C32 – FoxFire
>
> Rock Hall, MD
>
>
>
> *From:* CnC-List *On Behalf Of *syerdave
> via CnC-List
e chain plate.
>
> Just a possible explanation.
>
> You might check the symmetry of the lower spreaders and compare it to the
> uppers. Look for the possibility of it having been swapped in the past and
> naturally the ability to swap it back.
>
> Josh
>
> On Sun, Jun 24,
he mast?
>
> Josh
>
>
> On Sun, Jun 24, 2018, 3:17 PM J.R. Farrar via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> and that leads me more to believe the manual I saw. The lower attaches
>> to the spreader base in the forward part of the spreader. Putting it o
to bottom and obviously not cross.
>
> On Sun, Jun 24, 2018, 2:48 PM J.R. Farrar via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Interesting. So most here only know which way they go because that's the
>> way "they've always been". T
need to be accommodated by the spreader tips. The shrouds
> should be as straight as possible top to bottom and obviously not cross.
>
> On Sun, Jun 24, 2018, 2:48 PM J.R. Farrar via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Interesting. So most here only know w
rt at the chainplate, any
thoughts on the difference if any?
On Sun, Jun 24, 2018 at 2:36 PM, Josh Muckley via CnC-List <
cnc-list@cnc-list.com> wrote:
> Same with mine. CAP and D3 match and are larger. D1 and D2 match and are
> smaller.
>
> Josh
>
> On Sun, Jun 24, 2018,
(D3) is aft. I believe that this is typical of most boats and rigs. Are
> the shrouds different sizes?
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
> On Sun, Jun 24, 2018, 1:47 PM J.R. Farrar via CnC-List <
> cnc-list@cnc-list.com> wrote
Long time lurker occasional question asker...
Question came up at our club between 3 of the 33 MkII boats we have which
was the correct orientation of the three shrouds. The intermediate clearly
goes in the center of the base but the upper and lower could be swapped.
Swapping them means swapping
mailto:cnc-list@cnc-list.com> >
Cc: Jim Watts mailto:paradigmat...@gmail.com> >
Subject: Re: Stus-List Looking for prop shaft for '85 33 MkII
Whereabouts are you? Hard to recommend a source otherwise...
Jim Watts
Paradigm Shift
C&C 35 Mk III
Victoria, BC
On 5 Augus
ource otherwise...
Jim Watts
Paradigm Shift
C&C 35 Mk III
Victoria, BC
On 5 August 2015 at 07:08, J.R. Farrar via CnC-List mailto:cnc-list@cnc-list.com> > wrote:
Bumped into a log this weekend and bent the prop shaft (and damaged the prop).
Anyone know where I can find a replacem
Bumped into a log this weekend and bent the prop shaft (and damaged the prop).
Anyone know where I can find a replacement or at least the specs/length without
having to pull it from the boat first? I had an old prop that I put on and
dropped her back in the water. It’s good enough to get m
I recently purchased from SouthShore (last year) the pole car that fits that
internal track. You should find stopper screws at the top and bottom that stop
the car.
J.R.
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Paul
Fountain via CnC-List
Sent: Thursday, June
14 matches
Mail list logo
