Stus-List Re: any Bruce anchor users?

Same here, mine has always worked great, never let me down. Brad Crawford Dora Pearl C&C 36 Seattle From: dwight veinot via CnC-List Sent: Monday, August 23, 2021 9:39 AM To: Stus-List Cc: dwight veinot Subject: Stus-List Re: any Bruce anchor users? Get it. I have a Bruce k

Stus-List Small Cabin Stove

Hi Adam, Nice table and layout in your 36. Does that little heating stove work well for you? What brand is it and what fuel does it burn? Thanks, Brad Crawford C&C 36 Seattle Thanks to all of the subscribers that contributed to the list to help with the costs involved. If

Re: Stus-List Repowering a C&C 36 to Electric?

experience with an electric motor, might be worth the watch for you and your decision making. Cheers, Brad Crawford C&C 36 “Dora Pearl” Seattle Sent from my iPad > On Aug 10, 2020, at 2:40 PM, Gary Nylander via CnC-List > wrote: > >  > I am going to be a bit contrary in

Re: Stus-List Hydraulic backstay adjuster rebuild?

Lew Townsend in Seattle might be able to repair that for you. He did a great job on our Navtec Pump, not sure if he does Hydra Tech? His number is 206.498.7282 Good Luck, Brad Crawford CnC 36 - Seattle From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Shawn

Re: Stus-List Chartplotter mounting

Mike, Check this link out for a nice simple mount. I did this on my 36 and it works well http://www.pbase.com/mainecruising/plotter_mount_edson Brad Dora Pearl C &C 36 Seattle From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Michael Crombie via CnC-List Se

Re: Stus-List Holding tanks

Go visit marine sanitation supply next to fisheries supplies, they can help you out. Brad Dora Pearl C&C 36 Seattle Sent from my iPad > On Aug 31, 2018, at 1:55 PM, Dave. via CnC-List wrote: > > SLY has been using a Type 1 Sanitation System but these are no longer legal > in Puget Sound so

Re: Stus-List 1981 C&C 36' - Fresh Water Tank Replacement

M To: cnc-list@cnc-list.com Cc: Brad Crawford Subject: Re: Stus-List 1981 C&C 36' - Fresh Water Tank Replacement We had luck with welding. Get the right rod - LLDPE I think it is. Practice a little with a heat gun and it turns out great. Bill - 1985 c&c 37 starfire On Sun

Stus-List 1981 C&C 36' - Fresh Water Tank Replacement

Kracor or other manufacture tank ordered? Thanks, Brad Crawford C&C 36 "Dora Pearl" Seattle ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to

Re: Stus-List Battery monitor shunt location

. Thanks for sharing, Brad From: Dave S [mailto:syerd...@gmail.com] Sent: Sunday, June 10, 2018 6:31 PM To: DON JONSSON Cc: Brad Crawford; cnc-list@cnc-list.com Subject: Re: Stus-List Battery monitor shunt location Similar install in our 33-2 as documented here: https

Stus-List Battery monitor shunt location

I recently purchased a Victron battery monitor and am wondering where others, particularly 36' owners, have mounted their battery monitor shunts, if they have one? Many thanks, Brad Crawford "Dora Pearl" C&C 36 Seattle

Stus-List Stainless Steel Mixing Elbows

I am in the process of replacing my Yanmar mixing elbow on our 3HM motor. Does anyone have any experience with the stainless replacements being offered by HDI marine out of Vancouver Wa.? The price looks to be a little less and they look good on the website. Thanks, Brad Crawford Dora

Re: Stus-List baby stay

Well said, I agree Sent from my iPad > On Oct 26, 2017, at 6:10 AM, robert via CnC-List > wrote: > > My 1984 C&C 32 has a very robust mast.as was stated "more like an > aluminum telephone pole", nevertheless Rob Ball decided to outfit the rig > with a baby stay and for that reason, it s

Re: Stus-List News story

What happened to sailing? Sent from my iPad > On Oct 26, 2017, at 4:01 PM, John Pennie via CnC-List > wrote: > > Ok, wtf? Story on news tonight about a sailboat that was stranded in the > Pacific for 5months after their engine broke down on an otherwise functional > boat. Apparently the cre

Re: Stus-List Orcas on Puget Sound

Very cool, nice treat, especially close to home. Thanks for sharing. Brad Crawford Dora Pearl 81’ C&C 36 Elliott Bay From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Andrew Means via CnC-List Sent: Monday, April 11, 2016 11:05 AM To: cnc-list@cnc-list.com Cc: An

Re: Stus-List : off topic Skiing

Bill, Sounds cool, quite an adventure. High altitude big mountain skiing for sure? Thanks for sharing that story. Do you by chance have a link to pictures you could share? Maybe share them off list? bcrawf7...@comcast.net Fellow Skier Brad Crawford C&C 36 Seattle, WA

Re: Stus-List Propeller Shaft Coupling question

all along, the rear main seal on the tranny had been leaking for a while. Hopefully the shaft is in good shape. More later, Thanks for all the good advice, Brad Crawford CnC 36 "Dora Pearl" Seattle -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On B

Re: Stus-List Propeller Shaft Coupling question

Martin, What would be your suggestion, CSR, Canal, or Seaview for those repairs? Thanks, Brad Crawford CnC 36 Seattle From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Martin DeYoung via CnC-List Sent: Friday, June 5, 2015 11:50 AM To: cnc-list@cnc

Re: Stus-List Propeller Shaft Coupling question

-list@cnc-list.com Cc: Brad Crawford Subject: Re: Stus-List Propeller Shaft Coupling question I have been dealing with exactly that issue since I bought my boat 7 years ago. It hasn't been an issue and as a backup I have a zinc anode on the shaft about 3/8" from the packing nut just

Stus-List Propeller Shaft Coupling question

shaft, and then reinstalled for a final alignment. My question to the group is has anyone else been running around with a loose coupling and is this something I should be immediately concerned about? Thanks, Brad Crawford CnC 36 Seattle

Re: Stus-List Mirage in Newport

Thanks for sharing, amazing how fast those boats go, and what a great day. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Harry Hallgring via CnC-List Sent: Tuesday, May 19, 2015 6:10 AM To: cnc-list@cnc-list.com Cc: Harry Hallgring Subject: Re: Stus-List Mirage in Newport

Stus-List Kanzaki KBW10 Transmission Leakage

Maybe this has been asked or covered before? Has anyone experienced transmission fluid leaking from the rear of their transmission? I suspect it is a rear seal that has worn or gone bad. Were you able to have the seal replaced with the transmission in the boat or did you have to remove the trans

Re: Stus-List 2GM20F Engine will not start - Possible Fuse Issue.

&C 36 Elliott Bay From: Martin DeYoung [mailto:mdeyo...@deyoungmfg.com] Sent: Friday, August 15, 2014 10:23 AM To: Raymond Macklin; Brad Crawford Cc: cnc-list@cnc-list.com Subject: RE: Stus-List 2GM20F Engine will not start - Possible Fuse Issue. > Could it be heat related. As t

Re: Stus-List 2GM20F Engine will not start - Possible Fuse Issue.

I had a similar issue this last weekend. We motored from Elliott Bay to Port Ludlow, set the hook, shut the engine off, about a half hour later I decided to relocate the anchor. I depressed the starter switch and nothing happened, tried a couple of times, no start. So we stayed put figuring I

Stus-List Barient Model 27 2 speed self tailing winch parts

Does anyone know of a source for Barient Winch parts? The line lifter on our model 27's broke and I am looking for a replacement. It is a Barient 27, 2 speed, self tailing. Thanks, Brad CnC 36 Seattle ___ This List is provided by the C&C Ph

Re: Stus-List Aluminum coating

Do you think it would work well on a black pedestal? Mine has been eroding away in a few spots over the years. Might be best to remove the pedestal and have the whole thing powder coated, but maybe the zinc chromate primer and black paint might get me by for a few year? What do you think? An

Stus-List Signet SL 172 Depth Gauge

My Coastal Navigator DDS 200 depth gauge which is no longer in business seems to have retired itself. I'm thinking the instrument itself has gone bad, not the transducer. We just had the boat out of the water in April for fresh bottom paint, so I really don't want to pull her out again to repl

Re: Stus-List Boat AC Outlets

Edd, See the links below, http://www.hubbellcatalog.com/wiring/section-h-datasheet.asp?FAM=Ground_Faul t &PN=GF53OEMA http://wattsupmarine.blogspot.com/2011/01/gfci-danger-something-we-all-need-

Re: Stus-List Electronics - was Re: Setting GPS Waypoints

Andrew, I have used my iPad most of the time as a chartplotter also, using Navionics, we also carry back up paper charts. So far our long distance trips have been to the San Juan islands and Gulf Islands of British Columbia. Just out of curiosity, how far off shore have you used your iPad as a

Re: Stus-List floorboards

On the subject of floorboards, do others have squeaky, creaky floorboards like we do? Have you found a cure for it? Thanks, Brad CnC 36 Seattle From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of wwadjo...@aol.com Sent: Saturday, November 09, 2013 6:08 AM To: cnc-lis

Stus-List C & C 36 Head Sails

I am a C & C 36 owner and currently have a 135% and 155% for headsails. For those 36 owners, is a 100% considered the next size down for heavier air? Any thoughts , comments would be greatly appreciated. Thanks, Brad C & C 36 ___ This List is p

Re: Stus-List C & C 36 Front Hatch Plexiglass Replacement

lone the primer, and > it never leaked. > > Don > > > From: Brad Crawford [mailto:bcrawf7...@comcast.net] > Sent: July-02-13 9:19 AM > To: cnc-list@cnc-list.com > Subject: Stus-List C & C 36 Front Hatch Plexiglass Replacement > > Does anyone have any words of

Re: Stus-List C & C 36 Front Hatch Plexiglas Replacement

amp;C 43 Seattle cid:D1BF9853-22F7-47FB-86F2-4115CE0BAF2F From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Brad Crawford Sent: Tuesday, July 02, 2013 9:19 AM To: cnc-list@cnc-list.com Subject: Stus-List C & C 36 Front Hatch Plexiglass Replacement Does anyone have a

Re: Stus-List C & C 36 Front Hatch Plexiglass Replacement

a messy but easy DIY job. Joel 35/3 The Office Annapolis On Tue, Jul 2, 2013 at 12:18 PM, Brad Crawford wrote: Does anyone have any words of wisdom or advice for replacing a busted plexiglass of the front hatch on a '81 C&C 36? Would it be a Atkins and Hoyle hatch? I've be

Stus-List C & C 36 Front Hatch Plexiglass Replacement

Does anyone have any words of wisdom or advice for replacing a busted plexiglass of the front hatch on a '81 C&C 36? Would it be a Atkins and Hoyle hatch? I've been thinking of doing it myself but maybe it would be best to send it off to someone with lots of experience such as Hatchmasters or Sel

Re: Stus-List Genoa Low Lead Cars or Spring Loaded Blocks on Slides

Frank, Do you use the LLC-3 or the LLC-2 on your boat? Thanks, BC From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Frank Sent: Thursday, June 13, 2013 9:03 AM To: cnc-list@cnc-list.com Subject: Re: Stus-List Genoa Low Lead Cars or Spring Loaded Blocks on Slides

Stus-List Genoa Low Lead Cars or Spring Loaded Blocks on Slides

I am considering replacing my floppy snatch blocks on slides with either low lead cars or spring loaded blocks on slides. Does anyone have any input as to what works best. Brad C&C 36 ___ This List is provided by the C&C Photo Album http://www.cnc

Re: Stus-List Boom end fitting

Bill, Great Idea. Do you have any pictures of your set up and was the pricing reasonable? Thanks, Brad Crawford C&C 36 Seattle From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Bill Coleman Sent: Wednesday, May 29, 2013 12:24 PM To: cnc-list@cnc-list.com Sub

Stus-List Boom end fitting

I have an '81 C&C 36 and was wondering if anyone has ever found a boom extension with sheaves for that vintage boom so the outhaul and reefing lines could be routed to the very back end of the boom? Thanks, BC ___ This List is provided by the C&