Do not know about the Lide 110 but mine (Lide 210) has a sensor lock latch in the base. Make sure your issue is not caused because the latch is set to the "lock" position and the sensor bar is not moving at all. Hope this helps.
I would also like to say that your scanned image suffers from the same strange green vertical line on the left side. I commented about the issue on the following mails: http://lists.alioth.debian.org/pipermail/sane-devel/2014-July/032512.html 2014-10-29 21:12 GMT+01:00 Sane User <s...@nnn.sg>: > Sorry I'm pretty new to SANE, but it's been working great for months, then at > some point between a few weeks ago and today, my same-old scripted > "scanimage" command is returning nothing but blank pages. > > Can anyone suggest a direction for my bugfixing? I'm stumped. Thanks in > advance. > > THE COMMAND: > scanimage -d "genesys:libusb:002:003" --format=tiff --resolution=300 > --mode=Color > scan.tiff > > THE OUTPUT: > http://imgur.com/EVAj8zQ (see the streaks in there? any ideas?) > > I'm on Arch Linux, and do the usual "pacman -Syu" to keep software up to > date. I've rebooted, and run these diagnostics that all seem OK: > > # sane-find-scanner > found USB scanner (vendor=0x04a9 [Canon], product=0x1909 [CanoScan], > chip=GL124) at libusb:002:003 > > # scanimage --list-devices > [bjnp] create_broadcast_socket: bind socket to local address failed - Cannot > assign requested address > device `genesys:libusb:002:003' is a Canon LiDE 110 flatbed scanner > > # scanimage -d "genesys:libusb:002:003" -T > scanimage: scanning image of size 636x885 pixels at 8 bits/pixel > scanimage: acquiring gray frame, 8 bits/sample > scanimage: reading one scanline, 636 bytes... PASS > scanimage: reading one byte... PASS > scanimage: stepped read, 2 bytes... PASS > scanimage: stepped read, 4 bytes... PASS > scanimage: stepped read, 8 bytes... PASS > scanimage: stepped read, 16 bytes... PASS > scanimage: stepped read, 32 bytes... PASS > scanimage: stepped read, 64 bytes... PASS > scanimage: stepped read, 128 bytes... PASS > scanimage: stepped read, 256 bytes... PASS > scanimage: stepped read, 512 bytes... PASS > scanimage: stepped read, 1024 bytes... PASS > scanimage: stepped read, 1023 bytes... PASS > scanimage: stepped read, 511 bytes... PASS > scanimage: stepped read, 255 bytes... PASS > scanimage: stepped read, 127 bytes... PASS > scanimage: stepped read, 63 bytes... PASS > scanimage: stepped read, 31 bytes... PASS > scanimage: stepped read, 15 bytes... PASS > scanimage: stepped read, 7 bytes... PASS > scanimage: stepped read, 3 bytes... PASS > > # lsusb -v -d 04a9:1909 > Bus 002 Device 003: ID 04a9:1909 Canon, Inc. CanoScan LiDE 110 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 255 Vendor Specific Class > bDeviceSubClass 255 Vendor Specific Subclass > bDeviceProtocol 255 Vendor Specific Protocol > bMaxPacketSize0 64 > idVendor 0x04a9 Canon, Inc. > idProduct 0x1909 CanoScan LiDE 110 > bcdDevice 7.01 > iManufacturer 1 Canon > iProduct 2 CanoScan > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 39 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xa0 > (Bus Powered) > Remote Wakeup > MaxPower 500mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 3 > bInterfaceClass 255 Vendor Specific Class > bInterfaceSubClass 255 Vendor Specific Subclass > bInterfaceProtocol 255 Vendor Specific Protocol > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0001 1x 1 bytes > bInterval 8 > Device Qualifier (for other device speed): > bLength 10 > bDescriptorType 6 > bcdUSB 2.00 > bDeviceClass 255 Vendor Specific Class > bDeviceSubClass 255 Vendor Specific Subclass > bDeviceProtocol 255 Vendor Specific Protocol > bMaxPacketSize0 64 > bNumConfigurations 1 > Device Status: 0x0000 > (Bus Powered) > > > -- > sane-devel mailing list: sane-devel@lists.alioth.debian.org > http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/sane-devel > Unsubscribe: Send mail with subject "unsubscribe your_password" > to sane-devel-requ...@lists.alioth.debian.org -- sane-devel mailing list: sane-devel@lists.alioth.debian.org http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/sane-devel Unsubscribe: Send mail with subject "unsubscribe your_password" to sane-devel-requ...@lists.alioth.debian.org
