Hi, On Tue, Jul 02, 2002 at 08:09:52PM +0900, James Leigh wrote: > Thanks a lot. USB concerned messages are: > > In /var/log/messages (syslog has same lines): > Jul 2 07:51:54 cutee kernel: usb.c: registered new driver hub > Jul 2 07:51:54 cutee kernel: usb.c: registered new driver hid > Jul 2 07:51:54 cutee kernel: usb.c: registered new driver usbscanner > Jul 2 07:51:54 cutee kernel: scanner.c: USB Scanner support registered. > Jul 2 07:51:54 cutee kernel: usb-uhci.c: $Revision: 1.237 $ time 07:38:19 > Jul 2 2002 > Jul 2 07:51:54 cutee kernel: usb-uhci.c: High bandwidth mode enabled > > What is wrong with it?
Nothing. However that's only the messages concerning loading the drivers. I think the messages about recognizing the hardware are missing. Something like this (ohci, but uhci should be similar): Jul 1 23:10:01 hmg1 kernel: usb-ohci.c: USB OHCI at membase 0xe289b000, IRQ 9 Jul 1 23:10:01 hmg1 kernel: usb-ohci.c: usb-00:02.0, Acer Laboratories Inc. [ALi] USB 1.1 Controller Jul 1 23:10:01 hmg1 kernel: usb.c: new USB bus registered, assigned bus number 1 Jul 1 23:10:01 hmg1 kernel: usb.c: kmalloc IF df9d95c0, numif 1 Jul 1 23:10:01 hmg1 kernel: usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1 Jul 1 23:10:01 hmg1 kernel: usb.c: USB device number 1 default language ID 0x0 Jul 1 23:10:01 hmg1 kernel: Product: USB OHCI Root Hub Jul 1 23:10:01 hmg1 kernel: SerialNumber: e289b000 Jul 1 23:10:01 hmg1 kernel: hub.c: USB hub found Jul 1 23:10:01 hmg1 kernel: hub.c: 4 ports detected [...] Jul 1 23:10:01 hmg1 kernel: hub.c: port 1, portstatus 100, change 0, 12 Mb/s Jul 1 23:10:01 hmg1 kernel: hub.c: port 2, portstatus 101, change 1, 12 Mb/s Jul 1 23:10:01 hmg1 kernel: hub.c: port 2 connection change Jul 1 23:10:01 hmg1 kernel: hub.c: port 2, portstatus 101, change 1, 12 Mb/s Jul 1 23:10:01 hmg1 kernel: hub.c: port 2, portstatus 101, change 0, 12 Mb/s Jul 1 23:10:01 hmg1 last message repeated 3 times Jul 1 23:10:01 hmg1 kernel: hub.c: port 2, portstatus 103, change 10, 12 Mb/s Jul 1 23:10:01 hmg1 kernel: hub.c: USB new device connect on bus1/2, assigned device number 2 Jul 1 23:10:01 hmg1 kernel: usb.c: kmalloc IF df9d9980, numif 1 Jul 1 23:10:01 hmg1 kernel: usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0 Jul 1 23:10:01 hmg1 kernel: usb.c: unhandled interfaces on device Jul 1 23:10:01 hmg1 kernel: usb.c: USB device 2 (vend/prod 0x55f/0x6) is not claimed by any active driver.Jul 1 23:10:01 hmg1 kernel: Length = 18 Jul 1 23:10:01 hmg1 kernel: DescriptorType = 01 Jul 1 23:10:01 hmg1 kernel: USB version = 1.00 Jul 1 23:10:01 hmg1 kernel: Vendor:Product = 055f:0006 Jul 1 23:10:01 hmg1 kernel: MaxPacketSize0 = 8 Jul 1 23:10:01 hmg1 kernel: NumConfigurations = 1 Jul 1 23:10:01 hmg1 kernel: Device version = 1.00 [...] The last view messages are for my usb scanner. Jul 1 23:10:01 hmg1 kernel: usb.c: registered new driver usbscanner Jul 1 23:10:01 hmg1 kernel: usb.c: usbscanner driver claimed interface df9d9980 Jul 1 23:10:01 hmg1 kernel: scanner.c: 0.4.6:USB Scanner Driver And here the scanner driver claimed the scanner. Maybe 2.4 is more verbose than 2.2 but some messages about the hardware should be printed. Maybe you have a ohci instead of an uhci host controller? Or something else? Bye, Henning
