I've done a fresh RH 7.3 install last weekend. My USB HP Scanjet 5370 scanner (Avision unit) was found during ... so I thought I could use it immediately.
Not. sane-find-scanner finds three (!) scanners, all the same HP scanjet 5370C's but on different devices: sane-find-scanner: found SCSI scanner "HP ScanJet 5370C 6.00" at device /dev/scanner sane-find-scanner: found SCSI scanner "HP ScanJet 5370C 6.00" at device /dev/sg0 sane-find-scanner: found SCSI scanner "HP ScanJet 5370C 6.00" at device /dev/sga What's that supposed to mean ... and is this allright? scanimage -L says it doesn't identify any scanners. My /proc/bus/usb/devices says: T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=9800 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 17/900 us ( 2%), #Int= 1, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=9400 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03f0 ProdID=1004 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=DeskJet 970C S: SerialNumber=MY03V1506MJQ C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=01 Driver=usblp E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms I: If#= 0 Alt= 1 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=03f0 ProdID=0701 Rev= 0.01 S: SerialNumber=0000000000000000 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=hpusbscsi E: Ad=01(O) Atr=02(Bulk) MxPS= 8 Ivl= 0ms E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl= 10ms E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms /proc/scsi/scsi says: Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HP Model: ScanJet 5370C Rev: 6.00 Type: Scanner ANSI SCSI revision: 02 Anyone??? Give a scream if I didn't give all the neccessary info. Thnx, Jordi
