no, neither configure nor make are to be run in this case. after "pip install" it should just work.
On March 18, 2026 8:49:37 PM CDT, "Seohyeon “Alex” Lee" <[email protected]> wrote: >Is it pip install --no-build-isolation --editable . and straight to step 7 >in the README (make configure) then? > >On Thursday, March 19, 2026 at 10:02:08 AM UTC+9 [email protected] wrote: > >> If you use Conda then you should not run ./configure. >> >> <https://doc.sagemath.org/html/en/installation/source.html#using-conda> >> >> >> On March 18, 2026 7:39:42 PM CDT, "Seohyeon “Alex” Lee" < >> [email protected]> wrote: >> >>> I used miniforge. The recommendations say 'conda install' but what I >>> actually did was 'mamba install -c conda-forge [packages that showed up in >>> recommendations...] >>> >>> On Thursday, March 19, 2026 at 6:55:38 AM UTC+9 [email protected] wrote: >>> >>>> Do want to use Conda for your Sage installation? >>>> If not, you should isolate your Conda install from Sage (deactivate >>>> the environment, make sure that it's not in the PATH, etc) >>>> If yes, you seem to be following a wrong procedure. >>>> >>>> >>>> On Wed, Mar 18, 2026 at 2:37 PM Seohyeon “Alex” Lee >>>> <[email protected]> wrote: >>>> > >>>> > I have a Mac M1 and I'm working on building Sage from source. I >>>> followed the instructions from the README page and the linked >>>> documentation, but noticed I keep getting recommendations like the >>>> following at the end of ./configure. >>>> > ``` >>>> > config.status: creating convenience symlink venv -> >>>> local/var/lib/sage/venv-python3.12.5 >>>> > real_configure: >>>> > >>>> > notice: the following SPKGs did not find equivalent system packages: >>>> > >>>> > cypari fpylll mathjax pplpy primecountpy python3 4ti2 _develop >>>> _recommended coxeter3 free_fonts fricas gp2c igraph msolve onetbb >>>> perl_cpan_polymake_prereq perl_mongodb perl_term_readline_gnu polymake >>>> texlive texlive_luatex xindy >>>> > >>>> > checking for the package system in use... conda >>>> > real_configure: >>>> > >>>> > hint: installing the following system packages, if not >>>> > already present, is recommended and may avoid having to >>>> > build them (though some may have to be built anyway): >>>> > >>>> > $ conda install mathjax >>>> > >>>> > real_configure: >>>> > >>>> > hint: installing the following system packages, if not >>>> > already present, may provide additional optional features: >>>> > >>>> > $ conda install 4ti2 openssh pycodestyle esbonio open-fonts igraph tbb >>>> > >>>> > real_configure: >>>> > >>>> > hint: After installation, re-run configure using: >>>> > >>>> > $ make reconfigure >>>> > ``` >>>> > If I try installing the packages mentioned here, I get >>>> > ``` >>>> > Transaction >>>> > >>>> > Prefix: /Users/{myusername}/miniforge3/envs/sage-dev >>>> > >>>> > All requested packages already installed >>>> > ``` >>>> > If I ignore this and run make, I end up in the same loop. What can I >>>> do to break out of this cycle? >>>> > >>>> > -- >>>> > You received this message because you are subscribed to the Google >>>> Groups "sage-devel" group. >>>> > To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> > To view this discussion visit >>>> https://groups.google.com/d/msgid/sage-devel/13ee0a53-7c1d-4a52-accd-16343c9a8866n%40googlegroups.com. >>>> >>>> >>>> >>> > >-- >You received this message because you are subscribed to the Google Groups >"sage-devel" group. >To unsubscribe from this group and stop receiving emails from it, send an >email to [email protected]. >To view this discussion visit >https://groups.google.com/d/msgid/sage-devel/f3937133-4509-4655-9ebf-741847a98b3bn%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "sage-devel" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion visit https://groups.google.com/d/msgid/sage-devel/9EEE3124-01E6-4780-A8FD-E956B25E51C5%40gmail.com.
