MessageHi Kris,
Sorry that the terminology is decidedly a bit confusing to even my esteemed,
clever, and resourceful fellow wrenches.
Most folks are familiar with a typical natural draft, gas fired, storage tank,
water heater. It has a burner. A non-modulating burner. When the tank doesn't
call for heat, the main burner can just sit there doing nothing. In a 40 gallon
tank typically, 30,000 - 40,000 BTU/h, all 40,000 BTU/h on or nothing. The
nothing is _not_ the minimum fire rate. The nothing is off.
Every gas fired tankless water heater I have seen in the US uses a modulating
burner. When it is a _flow_ actuated machine a large flow will bring on the
high fire rate, ~200,000 BTU/h in the previous thread example. A smaller flow
will modulate that 200,000 BTU/h fire rate downwards. When the flow reduces
further, but still something more than a trickle (technically the actuation
flow) the machine will fire at the minimum fire rate which varies from heater
to heater but to use the previously cited example ~10,000 to 20,000 BTU/h. Now,
if you have a _temperature_ actuated machine and you are already at set point
the heater just sits there, _not_ firing when set point water passes through
the tankless. The perfect backup companion for SDHW, IMHO. Not firing (off) is
not the same as a fire rate that modulates to zero.
As I said (or should have said) early on, the trick to use a gas fired tankless
for SDHW backup is when the solar heated water needs just a tad more heat.
Class out. Enjoy the weekend.
Bill Loesch
Solar 1 - Saint Louis Solar
----- Original Message -----
From: Kristopher Schmid
To: 'RE-wrenches'
Sent: Friday, September 17, 2010 11:12 AM
Subject: Re: [RE-wrenches] On Demand Heaters for SDHW
Wayne,
Your statement that "The unit will turn off automatically once input water
temp reaches its programed output temp." seems to contradict the statement from
Bill saying "All tankless, including solar compatible (heaters which modulate
fire rate based on _inlet temperature_) have a minimum fire rate which is well
above zero."
Am i missing something?
Kris
Legacy Solar
864 Clam Falls Trail
Frederic, WI 54837
715-653-4295
sol...@legacysolar.com
www.legacysolar.com
-----Original Message-----
From: re-wrenches-boun...@lists.re-wrenches.org
[mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Wayne Irwin
Sent: Friday, September 17, 2010 9:40 AM
To: Wrenches
Subject: Re: [RE-wrenches] On Demand Heaters for SDHW
In our off grid home I installed a Rinnai propane tank less to support
the double pump drain-back system and have had no problems.
The tips that I suggest are: that the tank less be flushed out regularly,
even when not being used in-order to reduce any sediment.
If the water is hard, add a softener or at least a micro filter.
Scale build up can also be a problem.
If this tank less unit is being used as a back up, turn it off unless
needed.
The unit will turn off automatically once input water temp reaches its
programed output temp.
However, the initial water flow is cold enough to trigger the unit to
fire-up, wasting
100,000 btu's of fuel for a minute or so.
Wayne Irwin
Director of Engineering
Pure Energy Solar International Inc.
State Licensed Solar Contractor
License # CVC56695
wa...@pureenergysolar.com
http://pureenergysolar.com
352 377-6527 Office
352 336-3299 Fax
The content of this message is Pure Energy Solar Confidential. If you are
not the intended recipient and have received this message in error, any use or
distribution is prohibited. Please notify me immediately by reply e-mail and
delete this message from your computer system. Thank you.
> From: sol...@legacysolar.com
> To: re-wrenches@lists.re-wrenches.org
> Date: Fri, 17 Sep 2010 09:01:30 -0500
> Subject: Re: [RE-wrenches] On Demand Heaters for SDHW
>
> It all depends on whether you are talking financial payback or wise energy
> use. The people who use the least amount of hot water are the people who
> will experience the greatest energy use savings. They are a great option
> for weekend cabins since you don't have to remember to turn off the water
> heater when you leave and you don't have to wait for the tank to heat up
> when you return.
>
> Kris
>
> Legacy Solar
> 864 Clam Falls Trail
> Frederic, WI 54837
> 715-653-4295
> sol...@legacysolar.com
> www.legacysolar.com
> -----Original Message-----
> From: re-wrenches-boun...@lists.re-wrenches.org< br>>
[mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Todd Cory
> Sent: Thursday, September 16, 2010 1:55 PM
> To: RE-wrenches
> Subject: Re: [RE-wrenches] On Demand Heaters for SDHW
>
>
> The payback on a demand heater in energy savings is like 50+ years. A
> traditional tank heater, super insulated has very little loss.
>
> Todd
>
>
>
> Peter Parrish wrote:
> You’re right, Todd, there is often a space limitation. But overall, the
> tankless approach is more economical, eliminating the need to keep 80 odd
> gallons of water perpetually up to temperature. Remember the solar heated
> water is "make up water" and can contribute to the temperature of the
> traditional water heater only while hot water is being used. So, my guess
is
> that 1/2 of the day in a residence the traditional tank is keeping water
up
> to temperature for no apparent use.
>
> - Peter
>
> Peter T. Parrish, Ph.D., President
> California Solar Engineering, Inc.
> 820 Cynthia Ave., Los Angeles, CA 90065
> CA Lic. 854779, NABCEP Cert. 031806-26
> peter.parr...@calsolareng.com
> Ph 323-258-8883, Mobile 323-839-6108, Fax 323-258-8885
>
>
> ________________________________________
> From: re-wrenches-boun...@lists.re-wrenches.org
> [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Todd Cory
> Sent: Thursday, September 16, 2010 8:17 AM
> To: RE-wrenches
> Subject: Re: [RE-wrenches] On Demand Heaters for SDHW
>
> I know this was not the question, but this whole thread is predicated on
the
> use of a demand hot water heater. Unless there is a space limitation, why
> would this be done over a traditional tank unit?
>
> Todd
>
>
>
> Bill Loesch wrote:
&g t;
> Kris,
>
> Boiler manufacturers today get starry-eyed when their machines are able to
> provide a 10:1 turndown ratio. Even the venerable natural draft Bosch
125BS
> * provided a better than 4:1 turndown ratio and all the condensing
powervent
> units compared below regularly offer 10:1 and some better than 20:1. With
> each benefit comes a disadvantage, like with current production cars,
> serious repair/maintenance takes place primarily at the dealer since they
> are usually the only ones to pony up for the multitude of specialized test
> equipment. I find it a bit of backward progress to have to tell someone
that
> the reason they don't have reliable hot water is because they don't have
the
> current software update (due in no small part to the marketing gurus who
> have no qualms about using the customer as the proving grounds for their
> product). Many plumbers have no clue to the w orkings of a combustion
> analyzer, a necessary tool for negative pressure gas valve tuning and
> replacement (and a multitude
> of other tasks where the blue flame is no longer sufficient to be able to
> deliver optimum performance).
>
> Your Takagi needs AC power to (in order of decreasing current requirements
> for a generic power vented tankless)
> power the freeze protection heating elements
> run the primary combustion fan
> run the secondary combustion fan
> provide control to
> gas valve
> water valve
> control board (oftentimes with digital display) which provides the
> logic and timing circuits for the multitude of sensors and limit switches
> and remote controls and wireless remote controls etc., etc.
>
> Long live the thermocouple.
>
> My compliments on your simplistic approach to coordinate the solar storag
e
> tank and tankless. Simplicity is the ultimate sophistication.
>
> Bill Loesch
> Solar 1 - Saint Louis Solar
>
>
>
> PS I reiterate, despite other RE-Wrenches list comments to the contrary
> about
> "modulate to
> zero", NONE of ANY of the Big Five tankless manufacturers that market to
> North America have a low fire rate which modulates to zero or anything
near
> it for the very same reason that you will never get a trickle of hot water
> out of any tankless water heater. (~0.5 gpm minimum activation flow
> requirement)
>
> Comparing condensing heaters with ~200,000 max BTU/h input
> Bosch GWH C 800 ES 19,900 BTU/h
> Noritz NRC 111 11,000
> Paloma no condensing heaters
> Rinnai RC98HPe 9,500
> Takagi T-H2 13,000
>
> Thanks for your patience, I hope it was not too techn ical.
>
> ----- Original Message ----- From: "Peter Parrish"
> <peter.parr...@calsolareng.com>
> To: "'RE-wrenches'" <re-wrenches@lists.re-wrenches.org>
> Sent: Tuesday, September 14, 2010 10:37 AM
> Subject: [RE-wrenches] On Demand Heaters for SDHW
>
>
>
> We have a SDHW client that wants to replace his old water heater with
> a new tankless water heater. We do a SDHW system about once a year,
> and only for clients that are getting a PV system from us to begin
> with. So this is not a
> big business line for us and we are behind the curve in terms of
> understanding the latest technologies.
>
> As I remember from an excellent workshop that I took about four years
> ago: when used in conjunction with a SDWH system, the tankless heater
> should
>
> (1) Modulate heat input based on INPUT water temperature
> (2) Be able to modula te down to ZERO BTU/hr
>
> The only unit I knew of back then was the Bosch 125BS (I believe).
> Today I can't find any bigger units that fit the above requirements.
>
> Short of using two Bosch 125BS units in parallel, does anyone have a
> solution?
>
> - Peter
>
> Peter T. Parrish, Ph.D., President
> California Solar Engineering, Inc.
> 820 Cynthia Ave., Los Angeles, CA 90065
> CA Lic. 854779, NABCEP Cert. 031806-26 peter.parr...@calsolareng.com
> Ph 323-258-8883, Mobile 323-839-6108, Fax 323-258-8885
>
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches@lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re- wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches@lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches@lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches@lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
>
>
>
> --
>
> Todd Cory
> KE6SXS
> toddc...@finestplanet.com
> Mt. Shasta Energy Services
> License C-10 #811428
> P.O. Box 689
> Mt. Shasta, CA. 96067
> (530) 926-1079
> <!--[if !supportEmptyParas]--> <!--[endif]-->
> “I'd put my money on solar energy...I hope we don't have to wait till oil
> and coal run out before we tackle that."
> ∞ Thomas Edison, in conversation with Henry Ford and Harvey Firestone,
> March 1931
> <!--[if !supportEmptyParas]--> <!--[endif]-->
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches@lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List r ules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
------------------------------------------------------------------------------
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive:
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
