This thread seems to have died ... somehow it got mixed in with the
"strings of different orientation" thread. If anyone has further
input I would very much appreciate it as I have to schedule a long
trip to remedy this and want to have as much ammunition as possible.
Again, to restate the problem:
an Outback VFX3524 inverter installed on an E-panel in a remote off-
grid location. Voltage at the inverter input terminals is
fluctuating between 110 & 140+ volts continuously. AC in will not
connect so batteries can't charge. Output voltage measured at the
inverter output terminals is steady at 122v. When all household
loads are turned off the input terminal voltage stabilizes but AC
In still does not connect.
Generator does not seem to be at fault as output measured at the
gen. is stable even under load. System was working for about 1 1/2
years but under new ownership has been badly monitored and
batteries have become totally discharged.
I'm trying to determine if this is a circuit board problem so I can
perform a rescue mission by pulling some boards from an in-stock
inverter, Outback tech support are on holidays. Anyone had a
similar problem?
Mick,
referring to
there's not an auto-idle switch on that genset which may have
accidentally been set for auto, is there?
His generator was actually running in idle mode, operating the
household loads when I got there and the first thing I discovered was
that the voltage was ~90 volts coming in to the inverter. I manually
switched the generator to full speed and then checked the voltage
again, that is where I found the rapid fluctuations occurring at the
inverter.
Ron
On 27-Dec-08, at 1:23 PM, mick abraham wrote:
Ron wrote: "The owner told me...that someone had wired a switch
incorrectly
and when he turned it on the system "shut down". He then re-wired
it and
everything appeared ok but I'm wondering if this fried a board."
Mick replies: I've seen several times with Outback and other brands
(going as
far back as the Trace SW) where the inverter responds to an
accidental short
circuit in the household wiring by shutting itself off quicker than
a circuit
breaker can open. I'll bet that is what your customer
experienced...possibly
due to a nicked hot wire in that new switch box shorting out to
ground.
I suspect that (part of your customer's report) is completely
unrelated to
your present problem scenario. If it was my headache I would beg,
borrow,
or...rent a second generator to insert temporarily instead of the
Honda 3800.
That's the most conclusive way to determine fault or no-fault on
the generator.
Sometimes a genset will operate non-inverter loads OK and will
exhibit normal
looking voltage etc. but there still could be transients or spikes
which
render this input AC power unacceptable to the inverter/charger.
Thinking...there's not an auto-idle switch on that genset which may
have
accidentally been set for auto, is there?
Mick Abraham, Proprietor
www.abrahamsolar.com
Voice: 970-731-4675
Hi Mick & Jay,
I disconnected the gen. line to the inverter and tested the output
and got steady voltage. I then re-connected the inverter and
tested the gen. output from a different outlet and got steady
voltage, both around 122v. So I've ruled out the generator. It was
my first suspicion.
I have also noticed that when the household loads are off the
inverter output appears stable, doesn't fluctuate except about
every 20 seconds inverter audibly, the voltage drops from around
120 to 110 then resumes - as if the input was momentarily dropped.
Darryl,
I did play with the AC charge current lowering it to around 5 aac
but it didn't seem to make a difference. The owner told me, as an
afterthought that someone had wired a switch incorrectly and when
he turned it on the system "shut down". He then re-wired it and
everything appeared ok but I'm wondering if this fried a board. I
know there is an ac control board in there ... could this be it?
BTW, it's a very small generator, Honda 3800.
Ron
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-
wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-
wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
_______________________________________________
List sponsored by Home Power magazine
List Address: RE-wrenches@lists.re-wrenches.org
Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
