Hi Bin,
On Sat, Jan 2, 2021 at 6:46 PM Bin Meng <bmeng...@gmail.com> wrote:
>
> Hi Pragnesh,
>
> On Sat, Jan 2, 2021 at 8:27 PM Pragnesh Patel <pragnesh.pa...@sifive.com>
> wrote:
> >
> > Hi BIn,
> >
> > 1) Please rebase this series on master.
>
> I remember I rebased it on master already.
It shows below,
pragneshp:sifive-qemu$ git am hw-riscv-sifive_u-Add-missing-SPI-support.patch
Applying: hw/block: m25p80: Add ISSI SPI flash support
error: patch failed: hw/block/m25p80.c:1134
error: hw/block/m25p80.c: patch does not apply
Patch failed at 0001 hw/block: m25p80: Add ISSI SPI flash support
Use 'git am --show-current-patch' to see the failed patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".
pragneshp:sifive-qemu$
>
> >
> > 2) When i tried to boot from SD card image it shows below,
> >
> > pragneshp:sifive-qemu$ ./build/riscv64-softmmu/qemu-system-riscv64 -M
> > sifive_u,msel=11 -m 4G -nographic -bios
> > ~/opensource/u-boot/spl/u-boot-spl.bin -device
> > sd-card,spi=true,drive=mycard -drive
> > file=~/opensource/u-boot/fsbl.gpt,id=mycard,format=raw,if=none
>
> The command is not correct. Please check the commit message of:
> [18/22] hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
>
> The command should be:
>
> $ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
> -bios u-boot-spl.bin -drive file=sdcard.img,if=sd
>
> Note the memory should be 8G and the SD card is already connected by
> the sifive_u machine codes. No need to create it via "-device
> sd-card".
Ok my bad. it's working now. thanks for the clarification.
>
> > qemu-system-riscv64: -device sd-card,spi=true,drive=mycard: Drive
> > 'mycard' is already in use by another device
> >
> >
> > I hacked the qemu code temporary and able to boot U-Boot from SD card,
> > below is my hack
> >
> > pragneshp:sifive-qemu$ git diff
> > diff --git a/block/block-backend.c b/block/block-backend.c
> > index ce78d30794..cfa739fa40 100644
> > --- a/block/block-backend.c
> > +++ b/block/block-backend.c
> > @@ -888,10 +888,11 @@ void blk_get_perm(BlockBackend *blk, uint64_t
> > *perm, uint64_t *shared_perm)
> > */
> > int blk_attach_dev(BlockBackend *blk, DeviceState *dev)
> > {
> > +#if 0
> > if (blk->dev) {
> > return -EBUSY;
> > }
> > -
> > +#endif
> >
> > After applying this hack, I was able to boot U-Boot from Sd card
> >
> > Bootlogs:
> >
> > pragneshp:sifive-qemu$ ./build/riscv64-softmmu/qemu-system-riscv64 -M
> > sifive_u,msel=11 -m 4G -nographic -bios
> > ~/opensource/u-boot/spl/u-boot-spl.bin -device
> > sd-card,spi=true,drive=mycard -drive
> > file=~/opensource/u-boot/fsbl.gpt,id=mycard,format=raw,if=none
> >
> > U-Boot SPL 2020.10-rc5-00007-gf9aadb57b1 (Dec 29 2020 - 17:48:05 +0530)
> > Trying to boot from MMC1
> >
> >
> > U-Boot 2020.10-rc5-00007-gf9aadb57b1 (Dec 29 2020 - 17:48:05 +0530)
> >
> > CPU: rv64imafdc
> > Model: SiFive HiFive Unleashed A00
> > DRAM: 4 GiB
> > MMC: spi@10050000:mmc@0: 0
> > Loading Environment from SPIFlash... Invalid bus 0 (err=-19)
> > *** Warning - spi_flash_probe_bus_cs() failed, using default environment
> >
> > In: serial@10010000
> > Out: serial@10010000
> > Err: serial@10010000
> > Net: eth0: ethernet@10090000
> > Hit any key to stop autoboot: 0
> > =>
> >
> > Thanks for the series.
> >
>
> Regards,
> Bin
