On Thu, Nov 23, 2017 at 04:39:10PM +0100, Cédric Le Goater wrote:
> Hello,
>
> The model should be QOM'ified.
>
> On 11/20/2017 04:24 AM, Michael Davidsaver wrote:
> > Signed-off-by: Michael Davidsaver <mdavidsa...@gmail.com>
> > ---
> > hw/i2c/Makefile.objs | 1 +
> > hw/i2c/mpc8540_i2c.c | 287
> > +++++++++++++++++++++++++++++++++++++++++++++++++++
> > 2 files changed, 288 insertions(+)
> > create mode 100644 hw/i2c/mpc8540_i2c.c
> >
> > diff --git a/hw/i2c/Makefile.objs b/hw/i2c/Makefile.objs
> > index 0594dea3ae..79af1dd901 100644
> > --- a/hw/i2c/Makefile.objs
> > +++ b/hw/i2c/Makefile.objs
> > @@ -9,3 +9,4 @@ common-obj-$(CONFIG_IMX_I2C) += imx_i2c.o
> > common-obj-$(CONFIG_ASPEED_SOC) += aspeed_i2c.o
> > obj-$(CONFIG_OMAP) += omap_i2c.o
> > obj-$(CONFIG_PPC4XX) += ppc4xx_i2c.o
> > +obj-$(CONFIG_E500) += mpc8540_i2c.o
> > diff --git a/hw/i2c/mpc8540_i2c.c b/hw/i2c/mpc8540_i2c.c
> > new file mode 100644
> > index 0000000000..884052cc9b
> > --- /dev/null
> > +++ b/hw/i2c/mpc8540_i2c.c
> > @@ -0,0 +1,287 @@
> > +/*
> > + * MPC8540 I2C bus interface
> > + * As described in
> > + * MPC8540 PowerQUICC III Integrated Host Processor Reference Manual, Rev.
> > 1
> > + * Part 2 chapter 11
> > + *
> > + * Copyright (c) 2015 Michael Davidsaver
> > + *
> > + * This work is licensed under the terms of the GNU GPL, version 2. See
> > + * the LICENSE file in the top-level directory.
> > + */
> > +#include "qemu/osdep.h"
> > +#include "qemu/log.h"
> > +#include "hw/hw.h"
> > +#include "hw/registerfields.h"
> > +#include "hw/i2c/i2c.h"
> > +#include "hw/sysbus.h"
> > +
> > +/* #define DEBUG_LVL 0 */
> > +
> > +#ifdef DEBUG_LVL
> > +#define DPRINTK(LVL, FMT, ...) do { if ((LVL) <= DEBUG_LVL) { \
> > + printf(TYPE_MPC8540_I2C " : " FMT, ## __VA_ARGS__); } } while (0)
>
> hmm, I am not sure 'printfs' are welcomed in QEMU.
They're not, tracepoints are preferred. I tend to be ok with debug
macros like this, though, since they can be convenient. It should at
least be fprintf(stderr, ...) though.
>
> > +#else
> > +#define DPRINTK(LVL, FMT, ...) do {} while (0)
> > +#endif
> > +
> > +#define LOG(MSK, FMT, ...) qemu_log_mask(MSK, TYPE_MPC8540_I2C \
> > + " : " FMT, ## __VA_ARGS__)
> >
> > +#define TYPE_MPC8540_I2C "mpc8540-i2c"
> > +#define MPC8540_I2C(obj) OBJECT_CHECK(I2CState, (obj), TYPE_MPC8540_I2C)
> > +
> > +/* offsets relative to CCSR offset 0x3000 */
> > +#define R_I2CADR (0)
> > +#define R_I2CFDR (4)
> > +#define R_I2CCR (8)
> > +#define R_I2CSR (0xc)
> > +#define R_I2CDR (0x10)
> > +#define R_I2CDFSRR (0x14)
> > +
> > +FIELD(I2CCR, MEN, 7, 1)
> > +FIELD(I2CCR, MIEN, 6, 1)
> > +FIELD(I2CCR, MSTA, 5, 1)
> > +FIELD(I2CCR, MTX, 4, 1)
> > +FIELD(I2CCR, TXAK, 3, 1)
> > +FIELD(I2CCR, RSTA, 2, 1)
> > +FIELD(I2CCR, BCST, 0, 1)
> > +
> > +FIELD(I2CSR, MCF, 7, 1)
> > +FIELD(I2CSR, MAAS, 6, 1)
> > +FIELD(I2CSR, MBB, 5, 1)
> > +FIELD(I2CSR, MAL, 4, 1)
> > +FIELD(I2CSR, BCSTM, 3, 1)
> > +FIELD(I2CSR, SRW, 2, 1)
> > +FIELD(I2CSR, MIF, 1, 1)
> > +FIELD(I2CSR, RXAK, 0, 1)
> > +
> > +typedef struct I2CState {
> > + SysBusDevice parent_obj;
> > +
> > + I2CBus *bus;
> > +
> > + uint8_t ctrl, sts;
> > + uint8_t freq, filt;
> > + /* Reads are pipelined, this is the next data value */
> > + uint8_t dbuf;
> > +
> > + qemu_irq irq;
> > +
> > + MemoryRegion mmio;
> > +} I2CState;
>
> May be use MPC8540I2CState ? I would put the definition in a header file
>
> > +#define I2CCR(BIT) FIELD_EX32(i2c->ctrl, I2CCR, BIT)
> > +#define I2CSR(BIT) FIELD_EX32(i2c->sts, I2CSR, BIT)
> > +
> > +#define I2CSR_SET(BIT, VAL) do {\
> > + i2c->sts = FIELD_DP32(i2c->sts, I2CSR, BIT, VAL);\
> > + } while (0)
> > +
> > +static
> > +void mpc8540_update_irq(I2CState *i2c)
> > +{
> > + int ena = i2c->ctrl & 0x40,
> > + sts = i2c->sts & 0x02,
> > + act = !!(ena && sts);
>
> OK. why not :) Three distinct lines would be better. This is minor.
>
> > + DPRINTK(1, "IRQ %c ena %c sts %c\n",
> > + act ? 'X' : '_',
> > + ena ? 'X' : '_',
> > + sts ? 'X' : '_');
> > +
> > + qemu_set_irq(i2c->irq, act);
> > +}
> > +
> > +static
> > +uint64_t mpc8540_i2c_read(void *opaque, hwaddr addr, unsigned size)
> > +{
> > + I2CState *i2c = opaque;
> > + uint32_t val, offset = addr;
>
> This 'offset = addr' looks useless. do you really need it ?
>
>
> > +
> > + switch (offset) {
> > + case R_I2CADR: /* ADDR */
> > + val = 0;
> > + break;
> > + case R_I2CFDR: /* Freq Div. */
> > + val = i2c->freq;
> > + break;
> > + case R_I2CCR: /* CONTROL */
> > + val = i2c->ctrl & ~0x06;
> > + break;
> > + case R_I2CSR: /* STATUS */
> > + val = i2c->sts;
> > + break;
> > + case R_I2CDR: /* DATA */
> > + /* Reads are "pipelined" and so return the previous value of the
> > + * register
> > + */
> > + val = i2c->dbuf;
> > + if (I2CCR(MEN) && I2CSR(MBB)) { /* enabled and busy */
> > + if (!i2c_bus_busy(i2c->bus) || I2CCR(MTX)) {
> > + LOG(LOG_GUEST_ERROR, "Read during addr or tx\n");
> > + i2c->dbuf = 0xff;
> > + } else {
> > + int ret = i2c_recv(i2c->bus);
> > + i2c->dbuf = (uint8_t)ret;
> > + DPRINTK(0, "READ %02x ('%c')\n", i2c->dbuf,
> > (char)i2c->dbuf);
> > + I2CSR_SET(MIF, 1);
> > + I2CSR_SET(RXAK, 0);
> > + mpc8540_update_irq(i2c);
> > + }
> > + } else {
> > + i2c->dbuf = 0xff;
> > + LOG(LOG_GUEST_ERROR, "Read when not enabled or busy\n");
> > + }
> > + break;
> > + case R_I2CDFSRR: /* FILTER */
> > + val = i2c->filt;
> > + break;
> > + default:
> > + val = 0xff;
> > + }
> > +
> > + DPRINTK(offset == 0xc ? 2 : 1, " read %08x -> %08x\n",
> > + (unsigned)offset, (unsigned)val);
> > + return val;
> > +}
> > +
> > +static
> > +void mpc8540_i2c_write(void *opaque, hwaddr addr, uint64_t val, unsigned
> > size)
> > +{
> > + I2CState *i2c = opaque;
> > + uint32_t offset = addr;
> > +
> > + DPRINTK(1, " write %08x <- %08x\n", (unsigned)offset, (unsigned)val);
> > +
> > + switch (offset) {
> > + case R_I2CADR: /* ADDR */
> > + break;
> > + case R_I2CFDR: /* Freq Div. */
> > + i2c->freq = val & 0x3f;
> > + break;
> > + case R_I2CCR: /* CONTROL CCR */
> > + if (!FIELD_EX32(val, I2CCR, MEN)) {
> > + DPRINTK(0, "Not Enabled\n");
> > +
> > + } else if (!I2CCR(MSTA) && FIELD_EX32(val, I2CCR, MSTA)) {
> > + /* MSTA 0 -> 1 is START */
> > +
> > + I2CSR_SET(MBB, 1);
> > + DPRINTK(0, "START\n");
> > + i2c_end_transfer(i2c->bus); /* paranoia */
> > +
> > + } else if (I2CCR(MSTA) && !FIELD_EX32(val, I2CCR, MSTA)) {
> > + /* MSTA 1 -> 0 is STOP */
> > +
> > + I2CSR_SET(MBB, 0);
> > + DPRINTK(0, "STOP\n");
> > + i2c_end_transfer(i2c->bus);
> > +
> > + } else if (I2CCR(MSTA) && FIELD_EX32(val, I2CCR, RSTA)) {
> > + i2c_end_transfer(i2c->bus);
> > + I2CSR_SET(MBB, 1);
> > + DPRINTK(0, "REP START\n");
> > +
> > + }
> > + /* RSTA always reads zero, bit 1 unusd */
> > + val &= 0xf9;
> > + i2c->ctrl = val;
> > + mpc8540_update_irq(i2c);
> > + break;
> > + case R_I2CSR: /* STATUS CSR */
> > + /* only MAL and MIF are writable */
> > + val &= 0x12;
> > + i2c->sts &= ~0x12;
> > + i2c->sts |= val;
> > + mpc8540_update_irq(i2c);
> > + break;
> > + case R_I2CDR: /* DATA CDR */
> > + if (I2CCR(MEN) && I2CSR(MBB)) { /* enabled and busy */
> > + if (!i2c_bus_busy(i2c->bus)) {
> > + if (i2c_start_transfer(i2c->bus, val >> 1, val & 1)) {
> > + LOG(LOG_GUEST_ERROR, "I2C no device %02x\n",
> > + (unsigned)(val & 0xfe));
> > + } else {
> > + DPRINTK(0, "ADDR %02x\n", (unsigned)(val & 0xfe));
> > + }
> > + I2CSR_SET(MIF, 1);
> > + I2CSR_SET(RXAK, 0);
> > +
> > + } else if (I2CCR(MTX)) {
> > + DPRINTK(0, "WRITE %02x\n", (unsigned)val);
> > + i2c_send(i2c->bus, val);
> > + I2CSR_SET(MIF, 1);
> > + I2CSR_SET(RXAK, 0);
> > + } else {
> > + LOG(LOG_GUEST_ERROR, "I2CDR Write during read\n");
> > + }
> > + mpc8540_update_irq(i2c);
> > + } else {
> > + LOG(LOG_GUEST_ERROR, "I2CDR Write when not enabled or busy\n");
> > + }
> > + break;
> > + case R_I2CDFSRR: /* FILTER */
> > + val &= 0x3f;
> > + i2c->filt = val;
> > + break;
> > + }
> > +
> > + DPRINTK(1, "I2CCR = %02x I2SCR = %02x\n", i2c->ctrl, i2c->sts);
> > +}
> > +
> > +static const MemoryRegionOps i2c_ops = {
> > + .read = mpc8540_i2c_read,
> > + .write = mpc8540_i2c_write,
> > + .endianness = DEVICE_NATIVE_ENDIAN,
> > + .impl = {
> > + .min_access_size = 1,
> > + .max_access_size = 1,
> > + },
> > +};
> > +
> > +static
> > +void mpc8540_i2c_reset(DeviceState *dev)
> > +{
> > + I2CState *i2c = MPC8540_I2C(dev);
> > +
> > + i2c->sts = 0x81; /* transfer complete and ack received */
> > +}
> > +
> > +static int mpc8540_i2c_inst_init(SysBusDevice *dev)
> > +{
> > + I2CState *i2c = MPC8540_I2C(dev);
> > +
> > + i2c->bus = i2c_init_bus(&dev->parent_obj, "bus");
> > +
> > + memory_region_init_io(&i2c->mmio, &dev->parent_obj.parent_obj,
> > + &i2c_ops, i2c, TYPE_MPC8540_I2C, 0x18);
> > +
> > + sysbus_init_mmio(dev, &i2c->mmio);
> > + sysbus_init_irq(dev, &i2c->irq);
> > + return 0;
> > +}
>
> This should be a realize routine.
Ah.. that's a good point, actually. On that basis, I'm pulling the
draft patch from ppc-for-2.12
> > +static void mpc8540_i2c_class_init(ObjectClass *klass, void *data)
> > +{
> > + DeviceClass *dc = DEVICE_CLASS(klass);
> > + SysBusDeviceClass *k = SYS_BUS_DEVICE_CLASS(klass);
> > +
> > + k->init = &mpc8540_i2c_inst_init;
> > + dc->reset = &mpc8540_i2c_reset;
> > +}
> > +
> > +static const TypeInfo mpc8540_i2c_type = {
> > + .name = TYPE_MPC8540_I2C,
> > + .parent = TYPE_SYS_BUS_DEVICE,
> > + .instance_size = sizeof(I2CState),
> > + .class_size = sizeof(SysBusDeviceClass),
> > + .class_init = mpc8540_i2c_class_init,
> > +};
> > +
> > +static void mpc8540_i2c_register(void)
> > +{
> > + type_register_static(&mpc8540_i2c_type);
> > +}
> > +
> > +type_init(mpc8540_i2c_register)
> >
>
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
signature.asc
Description: PGP signature
