Signed-off-by: Markus Armbruster <arm...@redhat.com> Message-ID: <20250527073916.1243024-9-arm...@redhat.com> Reviewed-by: Eric Blake <ebl...@redhat.com> --- qapi/block-core.json | 2 +- qapi/dump.json | 6 +++--- qapi/migration.json | 26 +++++++++++++------------- qapi/misc.json | 4 ++-- 4 files changed, 19 insertions(+), 19 deletions(-)
diff --git a/qapi/block-core.json b/qapi/block-core.json index f0faca1054..7b0548dc2e 100644 --- a/qapi/block-core.json +++ b/qapi/block-core.json @@ -1589,7 +1589,7 @@ # # @bitmap-mode: Specifies the type of data the bitmap should contain # after the operation concludes. Must be present if a bitmap was -# provided, must NOT be present otherwise. (Since 4.2) +# provided, must **not** be present otherwise. (Since 4.2) # # @compress: true to compress data, if the target format supports it. # (default: false) (since 2.8) diff --git a/qapi/dump.json b/qapi/dump.json index f2835c0b47..d0ba1f0596 100644 --- a/qapi/dump.json +++ b/qapi/dump.json @@ -54,9 +54,9 @@ # @paging: if true, do paging to get guest's memory mapping. This # allows using gdb to process the core file. # -# IMPORTANT: this option can make QEMU allocate several gigabytes -# of RAM. This can happen for a large guest, or a malicious guest -# pretending to be large. +# **Important**: this option can make QEMU allocate several +# gigabytes of RAM. This can happen for a large guest, or a +# malicious guest pretending to be large. # # Also, paging=true has the following limitations: # diff --git a/qapi/migration.json b/qapi/migration.json index 84edcf81e4..4963f6ca12 100644 --- a/qapi/migration.json +++ b/qapi/migration.json @@ -407,7 +407,7 @@ # @postcopy-ram: Start executing on the migration target before all of # RAM has been migrated, pulling the remaining pages along as # needed. The capacity must have the same setting on both source -# and target or migration will not even start. NOTE: If the +# and target or migration will not even start. **Note:** if the # migration fails during postcopy the VM will fail. (since 2.6) # # @x-colo: If enabled, migration will never end, and the state of the @@ -801,10 +801,10 @@ # (Since 2.8) # # @avail-switchover-bandwidth: to set the available bandwidth that -# migration can use during switchover phase. NOTE! This does not -# limit the bandwidth during switchover, but only for calculations -# when making decisions to switchover. By default, this value is -# zero, which means QEMU will estimate the bandwidth +# migration can use during switchover phase. **Note:** this does +# not limit the bandwidth during switchover, but only for +# calculations when making decisions to switchover. By default, +# this value is zero, which means QEMU will estimate the bandwidth # automatically. This can be set when the estimated value is not # accurate, while the user is able to guarantee such bandwidth is # available when switching over. When specified correctly, this @@ -982,10 +982,10 @@ # (Since 2.8) # # @avail-switchover-bandwidth: to set the available bandwidth that -# migration can use during switchover phase. NOTE! This does not -# limit the bandwidth during switchover, but only for calculations -# when making decisions to switchover. By default, this value is -# zero, which means QEMU will estimate the bandwidth +# migration can use during switchover phase. **Note:** this does +# not limit the bandwidth during switchover, but only for +# calculations when making decisions to switchover. By default, +# this value is zero, which means QEMU will estimate the bandwidth # automatically. This can be set when the estimated value is not # accurate, while the user is able to guarantee such bandwidth is # available when switching over. When specified correctly, this @@ -1192,10 +1192,10 @@ # (Since 2.8) # # @avail-switchover-bandwidth: to set the available bandwidth that -# migration can use during switchover phase. NOTE! This does not -# limit the bandwidth during switchover, but only for calculations -# when making decisions to switchover. By default, this value is -# zero, which means QEMU will estimate the bandwidth +# migration can use during switchover phase. **Note:** this does +# not limit the bandwidth during switchover, but only for +# calculations when making decisions to switchover. By default, +# this value is zero, which means QEMU will estimate the bandwidth # automatically. This can be set when the estimated value is not # accurate, while the user is able to guarantee such bandwidth is # available when switching over. When specified correctly, this diff --git a/qapi/misc.json b/qapi/misc.json index dcf9f7df5b..4b9e601cfa 100644 --- a/qapi/misc.json +++ b/qapi/misc.json @@ -222,8 +222,8 @@ # .. note:: This command only exists as a stop-gap. Its use is highly # discouraged. The semantics of this command are not guaranteed: # this means that command names, arguments and responses can change -# or be removed at ANY time. Applications that rely on long term -# stability guarantees should NOT use this command. +# or be removed at **any** time. Applications that rely on long +# term stability guarantees should **not** use this command. # # Known limitations: # -- 2.48.1
