<snip> > I'm running Redhat 8, did the same with Redhat 7.3. Redhat's > automatic-hardware-detection-on-boot gizmo rewrites the fstab file each > time. I haven't done a lot of investigating of this yet - maybe there's > a way to keep it from deleting the camera entry if the camera isn't > plugged in on bootup. Anyone? > remove kudzu from fstab and it wont me removed when not there but it will also not change is you get different scsi ids i have a few usb-scsi mass storage devices as well as a zip drive and a tape drive. i have mount points for each of the usb-scsi devices and then the first one i plugin gets the first adress and so forth for each on i have. > I've skimmed this thread, hopefully this is useful info, if not good > fortune with your camera. > > Cheers, > Bret > > On Sun, 2003-02-02 at 22:34, Dan Devine wrote: > > > > OK, tried that....all devices /dev/sda --> /dev/sdd return with "mount: > > /dev/sd? is not a valid block device"... > > > > I've also read through the PDF > > > > >http://www.omniflashproducts.com/downloads/OmniFlash/Linux/LinuxMountingInstructions.PDF > > > > > > Attached devices: > > Host: scsi0 Channel: 00 Id: 00 Lun: 00 > > Vendor: FUJIFILM Model: USB-DRIVEUNIT Rev: 1.00 > > Type: Direct-Access ANSI SCSI revision: 02 > > Host: scsi1 Channel: 00 Id: 00 Lun: 00 > > Vendor: ASUS Model: CRW-4816A Rev: 1.0 > > Type: CD-ROM ANSI SCSI revision: 02 > > Host: scsi2 Channel: 00 Id: 00 Lun: 00 > > Vendor: Model: Rev: > > Type: <NULL> ANSI SCSI revision: ffffffff > > > > > > It's there....how do I get to it? > > > > > > Thanks, > > > > DD > > > > > > On Sun, 2003-02-02 at 19:10, HakanTerzioglu wrote: > > > > > > > > Hi, > > > Your camera , as a mass-storage device, is a emulated SCSI device for > > > Linux, so if you look at your logs you can see which drive it is > > > bounded to, and so you can mount that drive and reach your photos. > > > For mine ( a cheap digital camera costed me 100$) it is /dev/sdb, > > > cause i have a scsi disk at /dev/sda. I mount usb cam like : > > > mount /dev/sdb /mnt/camera > > > and it just works. (My cam is not supported by gtkam either by the > > > way) > > > Be careful not to give something like /dev/sdb1 sdb2 or so, you have > > > to give only the device not a partiton. > > > > > > Generally digi cams have fat fs inside the internal memory so it wont > > > be a problem for Psyche to mount it with its default kernel. > > > > > > YOu can examine the logs to see the usb mass storage like ; > > > dmesg|grep usb > > > > > > > > > Cheers; > > > hakan. > > > > > > ----- Original Message ----- > > > From: Dan Devine > > > To: RedHat 8.0 mailing list > > > Sent: Monday, February 03, 2003 3:53 AM > > > Subject: Re: USB Camera and SCSI Mass Storage device > > > > > > Thanks for the help Stephen, > > > > > > here's what I'm seeing right now (directory/contents)... > > > > > > /proc/scsi > > > ide-scsi scsi usb-storage-0 usb-storage-1 > > > > > > Also, I got the following......... > > > /proc/bus/usb > > > 001 002 003 devices drivers > > > > > > I can see how /dev/scd0 (scsi disk 0)... get's mapped to > > > /dev/cdrom. I just had to redo that with "ln -s /dev/scd0 > > > /dev/cdrom" since I first posted on the list. > > > > > > Where is the USB device? I've successfully mounted /dev/scd1 > > > with the addition of this line to the /etc/fstab > > > /dev/scd1 /camera usbfs defaults 0 0 > > > > > > > > > when examining the mount, I get the following directory...... > > > /camera > > > 001 002 003 devices drivers > > > > > > I've read the devices file and have found the entry for the > > > camera, but I'm unable to actually get any of the data or even > > > find a "drive" where I could see the files..... > > > > > > What am I doing wrong? > > > > > > > > > Thanks, > > > Dan > > > > > > > > > > > > I've also tried to map > > > > > > -- > > > Dan Devine <[EMAIL PROTECTED]> > > > > -- > > Dan Devine <[EMAIL PROTECTED]> > > > -- Dennis Gilmore <[EMAIL PROTECTED]>
signature.asc
Description: This is a digitally signed message part
