On Wed, 02 Jul 2014 00:39:37 +0000, Ralph Siegler wrote: > The display on this emac goes blank right at the end of booting, even > though display works fine from bsd.rd > > > Not using X and answered "No" to expecting to use X during install. > > Now emac with radeon is not in the list of supported machines, however > since things do work from bsd.rd I was wondering if there was any > setting I could "knock out" to just get basic console? > > > [ using 554672 bytes of bsd ELF symbol table ] > console out [ATY,Merlin_A]console in [keyboard] , using USB using parent > ATY,MerlinParent:: memaddr 98000000 size 8000000, : consaddr 9c008000, : > ioaddr 90020000, size 20000: width 1024 linebytes 1024 height 768 depth > 8 Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. > Copyright (c) 1995-2014 OpenBSD. All rights reserved. http:// > www.OpenBSD.org > > OpenBSD 5.5 (GENERIC) #166: Tue Mar 4 13:58:36 MST 2014 > dera...@macppc.openbsd.org:/usr/src/sys/arch/macppc/compile/GENERIC > real mem = 536870912 (512MB) > avail mem = 507748352 (484MB) > mainbus0 at root: model PowerMac6,4 cpu0 at mainbus0: 7457 (Revision > 0x101): 1249 MHz: 512KB L2 cache mem0 at mainbus0 spdmem0 at mem0: 512MB > DDR SDRAM non-parity PC2700CL2.5 memc0 at mainbus0: uni-n rev 0xd2 > "hw-clock" at memc0 not configured kiic0 at memc0 offset 0xf8001000 iic0 > at kiic0 mpcpcibr0 at mainbus0 pci: uni-north pci0 at mpcpcibr0 bus 0 > pchb0 at pci0 dev 11 function 0 "Apple UniNorth AGP" rev 0x00 radeondrm0 > at pci0 dev 16 function 0 "ATI Radeon 9200" rev 0x01 drm0 at radeondrm0 > radeondrm0: irq 48 mpcpcibr1 at mainbus0 pci: uni-north pci1 at > mpcpcibr1 bus 0 macobio0 at pci1 dev 23 function 0 "Apple Intrepid" rev > 0x00 openpic0 at macobio0 offset 0x40000: version 0x4614 feature 3f0302 > LE macgpio0 at macobio0 offset 0x50 "modem-reset" at macgpio0 offset > 0x1d not configured "modem-power" at macgpio0 offset 0x1c not configured > macgpio1 at macgpio0 offset 0x9: irq 47 "programmer-switch" at macgpio0 > offset 0x11 not configured "fan" at macgpio0 offset 0x0 not configured > "gpio0" at macgpio0 offset 0x6a not configured "gpio5" at macgpio0 > offset 0x6f not configured "gpio6" at macgpio0 offset 0x70 not > configured "extint-gpio4" at macgpio0 offset 0x5c not configured > "gpio11" at macgpio0 offset 0x75 not configured "extint-gpio15" at > macgpio0 offset 0x67 not configured "escc-legacy" at macobio0 offset > 0x12000 not configured zsc0 at macobio0 offset 0x13000: irq 22,23 zstty0 > at zsc0 channel 0 zstty1 at zsc0 channel 1 snapper0 at macobio0 offset > 0x10000: irq 30,1,2 "timer" at macobio0 offset 0x15000 not configured > adb0 at macobio0 offset 0x16000 apm0 at adb0: battery flags 0x9, 0% > charged piic0 at adb0 iic1 at piic0 "ivad-2" at iic1 addr 0x146 not > configured "ivad-eeprom" at iic1 addr 0x153 not configured "ivad-pwm" at > iic1 addr 0x14c not configured kiic1 at macobio0 offset 0x18000 iic2 at > kiic1 wdc0 at macobio0 offset 0x20000 irq 24: DMA atapiscsi0 at wdc0 > channel 0 drive 0 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ > 0 lun 0: <SONY, CD-RW CRX315E, NAK4> ATAPI 5/cdrom removable > cd0(wdc0:0:0): using BIOS timings, DMA mode 2 audio0 at snapper0 ohci0 > at pci1 dev 26 function 0 "Apple Intrepid USB" rev 0x00: irq 29, version > 1.0, legacy support ohci1 at pci1 dev 27 function 0 "NEC USB" rev 0x43: > irq 63, version 1.0 ohci2 at pci1 dev 27 function 1 "NEC USB" rev 0x43: > irq 63, version 1.0 ehci0 at pci1 dev 27 function 2 "NEC USB" rev 0x04: > irq 63 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "NEC EHCI root hub" > rev 2.00/1.00 addr 1 usb1 at ohci0: USB revision 1.0 uhub1 at usb1 > "Apple OHCI root hub" rev 1.00/1.00 addr 1 usb2 at ohci1: USB revision > 1.0 uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1 usb3 at > ohci2: USB revision 1.0 uhub3 at usb3 "NEC OHCI root hub" rev 1.00/1.00 > addr 1 mpcpcibr2 at mainbus0 pci: uni-north pci2 at mpcpcibr2 bus 0 > kauaiata0 at pci2 dev 13 function 0 "Apple Intrepid ATA" rev 0x00 wdc1 > at kauaiata0 irq 39: DMA wd0 at wdc1 channel 0 drive 0: <Maxtor 2F040L0> > wd0: 16-sector PIO, LBA48, 39205MB, 80293248 sectors wd0(wdc1:0:0): > using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 "Apple UniNorth Firewire" > rev 0x81 at pci2 dev 14 function 0 not configured gem0 at pci2 dev 15 > function 0 "Apple Uni-N2 GMAC" rev 0x80: irq 41, address > 00:0a:95:bf:c4:70 bmtphy0 at gem0 phy 0: BCM5221 100baseTX PHY, rev. 4 > uhub4 at uhub2 port 1 "Mitsumi Electric Hub in Apple Extended USB > Keyboard" rev 1.10/3.95 addr 2 uhidev0 at uhub4 port 3 configuration 1 > interface 0 "Mitsumi Electric Apple Extended USB Keyboard" rev 1.10/3.95 > addr 3 uhidev0: iclass 3/1 ukbd0 at uhidev0: 8 variable keys, 6 key > codes wskbd0 at ukbd0: console keyboard uhidev1 at uhub4 port 3 > configuration 1 interface 1 "Mitsumi Electric Apple Extended USB > Keyboard" rev 1.10/3.95 addr 3 uhidev1: iclass 3/0, 3 report ids uhid0 > at uhidev1 reportid 2: input=1, output=0, feature=0 uhid1 at uhidev1 > reportid 3: input=3, output=0, feature=0 vscsi0 at root scsibus1 at > vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets > bootpath: /pci@f4000000/ata-6@d/disk@0:/bsd root on wd0a > (8251ec938851c653.a) swap on wd0b dump on wd0b drm: initializing kernel > modesetting (RV280 0x1002:0x5962 0x1002:0x5962). > error: [drm:pid0:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM > drm: Using generic clock info radeondrm0: VRAM: 128M 0x0000000098000000 > - 0x000000009FFFFFFF (32M used) > trying to bind memory to uninitialized GART ! > error: [drm:pid0:radeon_ttm_backend_bind] *ERROR* failed to bind 1 pages > at 0x00000000 error: [drm:pid0:radeon_wb_init] *ERROR* (-22) create WB > bo failed error: [drm:pid0:r100_init] *ERROR* Disabling GPU acceleration > drm: radeon: cp finalized drm: radeon: cp finalized Finalizing pool > allocator ttm_pool_mm_shrink_fini stub drm: Zone kernel: Used memory at > exit: 0 kiB drm: radeon: ttm finalized drm: Forcing AGP to PCI mode > error: [drm:pid0:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM > drm: Using generic clock info radeondrm0: VRAM: 128M 0x0000000098000000 > - 0x000000009FFFFFFF (32M used) > radeondrm0: GTT: 512M 0x0000000078000000 - 0x0000000097FFFFFF drm: PCI > GART of 512M enabled (table at 0x0000000001C84000). > error: [drm:pid0:r100_cp_init_microcode] *ERROR* radeon_cp: Failed to > load firmware "radeon-r200_cp" > error: [drm:pid0:r100_cp_init] *ERROR* Failed to load firmware! > error: [drm:pid0:r100_startup] *ERROR* failed initializing CP (-2). > error: [drm:pid0:r100_init] *ERROR* Disabling GPU acceleration drm: > radeon: cp finalized drm: Connector Table: 1 (generic) > drm: No TMDS info found in BIOS drm: No TV DAC info found in BIOS > radeondrm0: 1024x768 wsdisplay0 at radeondrm0 mux 1: console (std, vt100 > emulation), using wskbd0 wsdisplay0: screen 1-5 added (std, vt100 > emulation)
disabling device radeondrm with ukc (for temporary fix) or config(8) solves the problem and gets console display "nevermind" -- lily t.
