Ethernet, WiFi, ADSL2+, and LEDS are fully functional.
The RFkill switch doesn't appear to be correctly configured.
Supporting the two TAE ports and SIP gateway was not attempted.
The firmware image needs to be kept below ~3.6MiB due to brnboot's dual
image magic. This is just enough for the above configuration plus
dropbear. Luci and other non-critical packages must be installed into
the jffs2 once the device has booted.
U-boot support was not attempted.
Signed-off-by: Oswald Buddenhagen <oswald.buddenha...@gmx.de>
---
.../linux/lantiq/base-files/etc/board.d/02_network | 8 +
.../etc/hotplug.d/firmware/10-rt2x00-eeprom | 2 +-
target/linux/lantiq/dts/ARV7506PW11.dts | 213 +++++++++++++++++++++
target/linux/lantiq/image/Makefile | 2 +
target/linux/lantiq/xway/profiles/arv.mk | 12 ++
5 files changed, 236 insertions(+), 1 deletion(-)
create mode 100644 target/linux/lantiq/dts/ARV7506PW11.dts
diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network
b/target/linux/lantiq/base-files/etc/board.d/02_network
index b27b802..1f06c26 100755
--- a/target/linux/lantiq/base-files/etc/board.d/02_network
+++ b/target/linux/lantiq/base-files/etc/board.d/02_network
@@ -39,6 +39,14 @@ ACMP252|GIGASX76X)
"4:lan:1" "3:lan:2" "2:lan:3" "1:lan:4" "5t@eth0"
;;
+# rtl8306g
+ARV7506PW11)
+ lan_mac=$(mtd_get_mac_binary board_config 22)
+ wan_mac=$(macaddr_add "$lan_mac" 1)
+ ucidef_add_switch "switch0" \
+ "4:lan:1" "3:lan:2" "2:lan:3" "1:lan:4" "5t@eth0"
+ ;;
+
# ar8316
ARV4519PW|ARV7510PW22|ARV7518PW|ARV752DPW22|ARV8539PW22)
ucidef_add_switch "switch0" \
diff --git
a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 5f1cb00..da10797 100644
--- a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -35,7 +35,7 @@ case "$FIRMWARE" in
"RT2860.eeprom" )
local board=$(lantiq_board_name)
case $board in
- ARV7510PW22|ARV7519PW|ARV752DPW|ARV752DPW22|VGV7519)
+ ARV7506PW11|ARV7510PW22|ARV7519PW|ARV752DPW|ARV752DPW22|VGV7519)
rt2x00_eeprom_extract "board_config" 520 256 1
;;
ARV7525PW)
diff --git a/target/linux/lantiq/dts/ARV7506PW11.dts
b/target/linux/lantiq/dts/ARV7506PW11.dts
new file mode 100644
index 0000000..bb9ffd4
--- /dev/null
+++ b/target/linux/lantiq/dts/ARV7506PW11.dts
@@ -0,0 +1,213 @@
+/dts-v1/;
+
+/include/ "danube.dtsi"
+
+/ {
+ model = "ARV7506PW11 - Alice/O2 IAD 4421";
+
+ chosen {
+ leds {
+ boot = &power;
+ failsafe = &power_red;
+ running = &power;
+
+ dsl = &dsl;
+ internet = &internet;
+ wifi = &wlan;
+ };
+ };
+
+ memory@0 {
+ reg = <0x0 0x4000000>;
+ };
+
+ sram@1F000000 {
+ vmmc@107000 {
+ status = "okay";
+ gpios = <&gpiomm 1 0>;
+ };
+ };
+
+ fpi@10000000 {
+ localbus@0 {
+ nor-boot@0 {
+ compatible = "lantiq,nor";
+ bank-width = <2>;
+ reg = <0 0x0 0x800000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "brnboot";
+ reg = <0x00000 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "stuff";
+ reg = <0x20000 0x70000>;
+ };
+
+ partition@90000 {
+ label = "rootfs_data";
+ reg = <0x90000 0x3B0000>;
+ };
+
+ partition@440000 {
+ label = "firmware";
+ reg = <0x440000 0x3B0000>;
+ };
+
+ partition@7f0000 {
+ label = "board_config";
+ reg = <0x7f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+
+ mac_addr {
+ compatible = "lantiq,eth-mac";
+ reg = <0 0x7f0016 0x6>;
+ mac-increment = <2>;
+ };
+
+ gpiomm: gpiomm@4000000 {
+ compatible = "lantiq,gpio-mm";
+ reg = <1 0x0 0x10 >;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ lantiq,shadow = <0x3>;
+ };
+ };
+
+ gpio: pinmux@E100B10 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ ebu {
+ lantiq,groups = "ebu cs1";
+ lantiq,function = "ebu";
+ };
+ exin {
+ lantiq,groups = "exin1";
+ lantiq,function = "exin";
+ };
+ pci_in {
+ lantiq,groups = "req2", "req1";
+ lantiq,function = "pci";
+ lantiq,pull = <2>;
+ lantiq,output = <0>;
+ };
+ pci_out {
+ lantiq,groups = "gnt1";
+ lantiq,function = "pci";
+ lantiq,output = <1>;
+ };
+ pci_rst {
+ lantiq,pins = "io21";
+ lantiq,pull = <2>;
+ lantiq,output = <1>;
+ };
+ switch_rst {
+ lantiq,pins = "io19";
+ };
+ leds {
+ lantiq,pins = "io2", "io3", "io4",
"io5", "io6", "io7", "io8", "io9", "io20";
+ lantiq,output = <1>;
+ lantiq,pull = <0>;
+ };
+ keys {
+ lantiq,pins = "io11", "io30";
+ lantiq,output = <0>;
+ lantiq,pull = <2>;
+ };
+ };
+ };
+
+ ifxhcd@E101000 {
+ status = "okay";
+ gpios = <&gpiomm 0 0>;
+ };
+
+ etop@E180000 {
+ phy-mode = "rmii";
+ };
+
+ pci@E105400 {
+ status = "okay";
+ gpio-reset = <&gpio 21 0>;
+ };
+
+ };
+
+ ralink_eep {
+ compatible = "ralink,eeprom";
+ ralink,eeprom = "RT2860.eeprom";
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <100>;
+
+ rfkill {
+ /* The button is labeled WLAN/WPS. The former seems
more useful. */
+ label = "rfkill";
+ gpios = <&gpio 11 1>;
+ linux,code = <0x211>;
+ };
+ reset {
+ label = "reset";
+ gpios = <&gpio 30 1>;
+ linux,code = <0x198>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ wlan: wlan {
+ label = "arv7506pw11:green:wlan";
+ gpios = <&gpio 2 1>;
+ };
+ power: power {
+ label = "arv7506pw11:green:power";
+ gpios = <&gpio 3 1>;
+ };
+ dsl: dsl {
+ label = "arv7506pw11:green:dsl";
+ gpios = <&gpio 4 1>;
+ };
+ internet: internet {
+ label = "arv7506pw11:green:internet";
+ gpios = <&gpio 5 1>;
+ };
+ power_red: power_red {
+ label = "arv7506pw11:red:power";
+ gpios = <&gpio 6 1>;
+ };
+ internet_red {
+ label = "arv7506pw11:red:internet";
+ gpios = <&gpio 7 1>;
+ };
+ info {
+ label = "arv7506pw11:green:info";
+ gpios = <&gpio 8 1>;
+ };
+ telefon {
+ label = "arv7506pw11:green:telefon";
+ gpios = <&gpio 9 1>;
+ };
+ info_red {
+ label = "arv7506pw11:red:info";
+ gpios = <&gpio 20 1>;
+ };
+ };
+};
diff --git a/target/linux/lantiq/image/Makefile
b/target/linux/lantiq/image/Makefile
index bc74e4f..7a5a564 100644
--- a/target/linux/lantiq/image/Makefile
+++ b/target/linux/lantiq/image/Makefile
@@ -352,6 +352,8 @@ ifeq ($(CONFIG_TARGET_lantiq_xway),y)
Image/BuildKernel/Profile/BTHOMEHUBV2B=$(call
Image/BuildKernel/Template,BTHOMEHUBV2B)
Image/Build/Profile/BTHOMEHUBV2B=$(call Image/BuildNAND/$(1),$(1),BTHOMEHUBV2B)
+$(eval $(call lantiqBrnImage,ARV7506PW11,BRNDA4421,0x7AB7ADAD,0x2083b8ed))
+
$(eval $(call lantiqImage,EASY50712))
$(eval $(call lantiqImage,ACMP252))
$(eval $(call lantiqImage,ARV4510PW))
diff --git a/target/linux/lantiq/xway/profiles/arv.mk
b/target/linux/lantiq/xway/profiles/arv.mk
index 976cd19..e20e403 100644
--- a/target/linux/lantiq/xway/profiles/arv.mk
+++ b/target/linux/lantiq/xway/profiles/arv.mk
@@ -78,6 +78,18 @@ endef
$(eval $(call Profile,ARV4519PW))
+define Profile/ARV7506PW11
+ NAME:=Alice/O2 IAD 4421 - ARV7506PW11
+ PACKAGES:= \
+ kmod-ltq-adsl-danube-mei kmod-ltq-adsl-danube \
+ kmod-ltq-adsl-danube-fw-b kmod-ltq-atm-danube \
+ ltq-adsl-app ppp-mod-pppoa \
+ kmod-rt2800-pci wpad-mini \
+ swconfig
+endef
+
+$(eval $(call Profile,ARV7506PW11))
+
define Profile/ARV7510PW22
NAME:=Astoria - ARV7510PW22
PACKAGES:=kmod-ltq-hcd-danube kmod-ledtrig-usbdev \
--
2.7.4.1.gb6fc189
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
