As for your question if the EEPROM are the same for all units, I just extract from 2 of my units and md5sum checks out the same.
On Sat, Jun 28, 2014 at 9:49 PM, Alpha Sparc <alphasp...@gmail.com> wrote:
> AFAIK there is only 1 model of GR7000 and the 2 units with me both
> have a file called RT30xxEEPROM.bin which is 512 bytes in /tmp/.
> No other partitions except mtd0 (uboot) and mtd1 (rootfs lzma).
> For users who want to use openwrt this is a problem because they need
> to extract the EEPROM by mounting a FAT formatted drive and copying
> out the file.
> Probably need to note this in the wiki.
> I am still having problems with the switch ar8316, ipv6 is detected
> but ipv4 cannot get through should be a config issue although I can't
> figure out the problem.
>
> I notice that support for lantiq mips34kc is also rather flaky, router
> somethings hangs and reboots abruptly...
> Is it possible to port the 34kc patches from TP-Link TD-W8970 SDK to
> OpenWRT? Is there a licensing issue.
> They have neatly place all their custom patches in a folder, porting
> should be doable.
>
>
> On Sat, Jun 28, 2014 at 4:03 PM, John Crispin <j...@phrozen.org> wrote:
>> Hi,
>>
>> i will postpone this patch till after BB. we will at that point fix up
>> the eep handling properly and merge/share the patches between ralink
>> and lantiq.
>>
>> do you know if all the boards have the same eep in the filesystem or do
>> they differ between units ?
>>
>> John
>>
>> On 27/06/2014 19:05, Alpha Sparc wrote:
>>> Move the Ralink EEPROM node into the PCI node to remove "wmac
>>> failed to load eeprom property" message
>>>
>>>
>>>
>>> ---
>>> a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
>>>
>>>
>> +++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
>>> @@ -41,6 +41,9 @@ case "$FIRMWARE" in ARV7525PW)
>>> rt2x00_eeprom_extract "board_config" 1040 512 0 ;; + GR7000) +
>>> rt2x00_eeprom_extract "board_config" 0 512 0 + ;; *)
>>> rt2x00_eeprom_die "board $board is not supported yet" ;;
>>>
>>> --- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network
>>> +++ b/target/linux/lantiq/base-files/etc/uci-defaults/02_network @@
>>> -128,8 +128,12 @@ DGN3500*) ;;
>>>
>>> GR7000) - ucidef_set_interface_wan "eth0" - uci set
>>> network.lan.ifname='' + lan_mac=$(mtd_get_mac_ascii uboot_env
>>> ethaddr) + wan_mac=$(macaddr_add "$lan_mac" 3) +
>>> ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" +
>>> ucidef_add_switch "switch0" "1" "1" + ucidef_add_switch_vlan
>>> "switch0" "1" "0t 1 2 3 4" + ucidef_add_switch_vlan "switch0"
>>> "2" "0t 5" ;;
>>>
>>> H201L) @@ -167,13 +171,23 @@ BTHOMEHUBV2B) ;; esac
>>>
>>> -[ -z "$(ls /lib/modules/`uname -r`/ltq_atm*)" ] || set_atm_wan
>>> "$vpi" "$vci" "$encaps" "$payload" +board=$(lantiq_board_id) +
>>> +case "$board" in
>>>
>>> -if [ -n "$(grep "system type.*: VR9" /proc/cpuinfo)" ]; then -
>>> set_vdsl_modem "$annex" "/lib/firmware/vdsl.bin" "av" "ptm" -else -
>>> set_adsl_modem "$annex" "/lib/firmware/adsl.bin" -fi +GR7000) +
>>> ;; + +*) + [ -z "$(ls /lib/modules/`uname -r`/ltq_atm*)" ] ||
>>> set_atm_wan "$vpi" "$vci" "$encaps" "$payload" + + if [ -n
>>> "$(grep "system type.*: VR9" /proc/cpuinfo)" ]; then +
>>> set_vdsl_modem "$annex" "/lib/firmware/vdsl.bin" "av" "ptm" +
>>> else + set_adsl_modem "$annex" "/lib/firmware/adsl.bin" +
>>> fi + ;; +esac
>>>
>>> [ -n "$lan_mac" ] && ucidef_set_interface_macaddr lan $lan_mac [ -n
>>> "$wan_mac" ] && ucidef_set_interface_macaddr wan $wan_mac
>>>
>>> ---
>>> a/target/linux/lantiq/base-files/etc/uci-defaults/03_wireless-wps
>>> +++
>>> b/target/linux/lantiq/base-files/etc/uci-defaults/03_wireless-wps
>>> @@ -8,7 +8,7 @@ set_wps() {
>>>
>>> board=$(lantiq_board_id) case $board in -WBMR) +WBMR|GR7000)
>>> config_load wireless config_foreach set_wps wifi-iface uci commit
>>> wireless
>>>
>>> --- a/target/linux/lantiq/xway/profiles/aztech.mk +++
>>> b/target/linux/lantiq/xway/profiles/aztech.mk @@ -2,6 +2,7 @@
>>> define Profile/GR7000 NAME:=Aztech GR7000 PACKAGES:= \
>>> kmod-ltq-deu-ar9 kmod-ltq-hcd-ar9 \ + kmod-rt2800-pci wpad \
>>> swconfig endef $(eval $(call Profile,GR7000))
>>>
>>> --- a/target/linux/lantiq/dts/GR7000.dts +++
>>> b/target/linux/lantiq/dts/GR7000.dts @@ -3,7 +3,7 @@ /include/
>>> "ar9.dtsi"
>>>
>>> / { - model = "GR7000 - Aztech GR7000"; + model = "Aztech
>>> GR7000";
>>>
>>> chosen { bootargs = "console=ttyLTQ0,115200 init=/etc/preinit"; @@
>>> -18,7 +18,7 @@ nor-boot@0 { compatible = "lantiq,nor"; bank-width =
>>> <2>; - reg = <0 0x0 0x2000000>; + reg
>>> = <0 0x0 0x800000>; #address-cells = <1>; #size-cells = <1>;
>>>
>>> @@ -29,16 +29,24 @@ };
>>>
>>> partition@20000 { - label = "uboot_env"; -
>>> reg = <0x20000 0x10000>; + label = "firmware"; +
>>> reg = <0x20000 0x7b0000>; + }; + +
>>> partition@7e0000 { + label = "board_config"; +
>>> reg = <0x7e0000 0x10000>; read-only; };
>>>
>>> - partition@30000 { - label =
>>> "firmware"; - reg = <0x30000 0x7d0000>; +
>>> partition@7f0000 { + label = "uboot_env"; +
>>> reg = <0x7f0000 0x10000>; + read-only; }; + };
>>> + };
>>>
>>> gpio: pinmux@E100B10 { @@ -70,12 +78,25 @@ }; };
>>>
>>> + etop@E180000 { + phy-mode = "rgmii"; +
>>> }; + ifxhcd@E101000 { status = "okay"; + gpios = <&gpio
>>> 5 0 + &gpio 14 0>; + lantiq,portmask =
>>> <0x3>; };
>>>
>>> pci@E105400 { status = "okay"; + + ralink_eep { +
>>> compatible = "ralink,eeprom"; + ralink,eeprom =
>>> "RT2860.eeprom"; + }; + };
>>>
>>> stp: stp@E100BB0 { _______________________________________________
>>> openwrt-devel mailing list openwrt-devel@lists.openwrt.org
>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
RT30xxEEPROM.bin
Description: Binary data
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
