Hi all, I have an ADB P.DGA4001N, but it is a different hardware than what is described in the wiki (http://wiki.openwrt.org/toh/adb/p.dg_a4001n1). What I get in the console at boot time after unsuccessful flashing is:
CFE version 1.0.37-106.24 for A4001N TEF 0001 BCM96328 (32bit,SP,BE) Build Date: Wed Dec 1 13:30:30 CET 2010 (sj1bovisem@thor) Copyright (C) 2000-2009 Broadcom Corporation. HS Serial flash device: name ID_W25X64, id 0xef17 size 8192KB Total Flash size: 8192K with 2048 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-4) : 96328dg2x2 Number of MAC Addresses (1-32) : 11 Base MAC Address : a4:52:6f:0c:ec:53 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80010000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80010000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80010000 [ 0.000000] Linux version 3.6.11 (fnord@tschunk) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Tue Jan 8 02:28:17 UTC 2013 [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0 [ 0.000000] CPU frequency is 320 MHz [ 0.000000] 32MB of RAM installed [ 0.000000] registering 32 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: A4001N-V0001 [ 0.000000] board_bcm963xx: unknown bcm963xx board: 96328dg2x2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350) [ 0.000000] Kernel panic - not syncing: unable to detect bcm963xx board After trying flashing several attitude adjustment and trunk binaries through serial console without success (getting Kernel panic - not syncing: unable to detect bcm963xx board) I followed instructions in http://wiki.openwrt.org/doc/devel/add.new.device and modified attitude adjustment's target/linux/brcm63xx/image/Makefile, adding the line $(call Image/Build/CFE,$(1),96328dg2x2,6328,96328dg2x2-8M-flash-generic,,--pad 4) and build_dir/linux-brcm63xx/linux-3.3.8/arch/mips/bcm63xx/boards/board_bcm963xx.c, where I simply copied the 963281TAN's definition and renamed as static struct board_info __initdata board_96328dg2x2 = { .name = "96328dg2x2", ... The resulting binary boots, but only the first time. I tried the squashfs image as well as the jffs2, and I get the same result: *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80010000 Linux file system CRC error. Corrupted image? web info: Waiting for connection on socket 0. CFE> It seems to be related to jffs2's filesystem initialization, because if I reboot after it is done, the device starts again, but after the initialization, it will fail. Any ideas on what I am missing? Regards. _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
