Got the cable working :) Here's the output:
Linux version 2.6.25.12 ([EMAIL PROTECTED]) (gcc version 4.2.4) #6 8 console [ttyS0] enabled Setting up paging and the MMU. Linux/CRIS port on ETRAX 100LX (c) 2001 Axis Communications AB Built 1 zonelists in Zone order, mobility grouping on. Total pages: 4080 Kernel command line: root=/dev/mtdblock1 rootfstype=squashfs,jffs2 init=/etc/pr0 PID hash table entries: 128 (order: 7, 512 bytes) ds1302: RTC found. ds1302: SDA, SCL, RST on PB0, PB1, GENIO2 rtc_time : 11:19:03 rtc_date : 2008-08-02 Dentry cache hash table entries: 4096 (order: 1, 16384 bytes) Inode-cache hash table entries: 2048 (order: 0, 8192 bytes) Memory: 30312k/32768k available (1279k kernel code, 2456k reserved, 319k data, ) Mount-cache hash table entries: 1024 net_namespace: 444 bytes NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 0, 8192 bytes) TCP established hash table entries: 1024 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered console [ttyS0] enabled fast_timer_init() squashfs: version 3.0 (2006/03/15) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered (default) ETRAX 100LX serial-driver 1.25 $, (c) 2000-2004 Axis Communications AB ttyS0 at 0xb0000060 is a builtin UART with DMA ttyS2 at 0xb0000070 is a builtin UART with DMA ttyS3 at 0xb0000078 is a builtin UART with DMA ETRAX 100LX 10/100MBit ethernet v2.0 (c) 1998-2007 Axis Communications AB eth0: changed MAC to 00:40:8c:cd:00:00 ETRAX 100LX USB Host Controller (2.6.25-rc9 port) version 1.00 hinko.4 (c) 2005B usb_devdrv: Etrax 100LX USB Revision 16 v1,2 usb_devdrv: Bulk timer interval, start:2 eot:6 usb_devdrv: Claimed interface for USB physical port 1 usb_devdrv: Claimed interface for USB physical port 2 crisv10_irq dbg: ctr_status_irq, controller status: host_mode hc-crisv10 hc-crisv10.0: ETRAX 100LX USB Host Controller (2.6.25-rc9 port) hc-crisv10 hc-crisv10.0: new USB bus registered, assigned bus number 1 hc-crisv10 hc-crisv10.0: reset hc-crisv10 hc-crisv10.0: start usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected cse0: Probing a 0x04000000 bytes large window at 0xe0000000. cse0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 cse0: Swapping erase regions for broken CFI table. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cse1: Probing a 0x04000000 bytes large window at 0xe4000000. cse0: 0x00800000 bytes of flash memory. Scanning flash for end of kernel magic Kernel ends at 0x000F0000 Using default partition table. Creating 2 MTD partitions on "cse0": 0x00000000-0x000f0000 : "kernel" 0x000f0000-0x00800000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=200000, len=600000 0x00200000-0x00800000 : "rootfs_data" Adding RAM partition for romfs image: /dev/flash1 at 0x00000000, size 0x00000000 I2C driver v2.2, (c) 1999-2004 Axis Communications AB GPIO port G: in_bits: 0x01FFFF3F out_bits: 0x3200003E val: F1FFFFFF GPIO port G: dir: 00000000 changeable: 01FFFF01 ETRAX 100LX GPIO driver v2.5, (c) 2001-2008 Axis Communications AB ds1302: RTC found. ds1302: SDA, SCL, RST on PB0, PB1, GENIO2 rtc_time : 11:19:04 rtc_date : 2008-08-02 nf_conntrack version 0.5.0 (2048 buckets, 8192 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP vegas registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 56k freed Please be patient, while OpenWrt loads ... Kernel panic - not syncing: Attempted to kill init!
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org http://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
