I got your concern, Your physical hardware needs to be in iLO / power 
management. So that you will have management  ilo IP address, username and 
password to enroll your hardware.

FYI: You don't need to have OS installed in your physical hardware to enroll 
hardware for your baremetal.

Thanks
Shanthakumar K

From: Jake G. [mailto:dj_dark_jungl...@yahoo.com]
Sent: Friday, August 23, 2013 12:15 PM
To: K, Shanthakumar
Cc: openstack@lists.openstack.org
Subject: Re: [Openstack] Baremetal - Hardware preparation

I am sorry if my explanation was hard to follow.

In order to enroll my hardware, Openstack requires the Servers IP address, 
username and password.
Since I have no OS installed on the hardware(physical server) I have no IP 
address and no username/password

On the hardware side only(not openstack) what needs to be done in order for 
Openstack to control the hardware?

Thanks


________________________________
From: "K, Shanthakumar" <shanthakuma...@hp.com<mailto:shanthakuma...@hp.com>>
To: Jake G. <dj_dark_jungl...@yahoo.com<mailto:dj_dark_jungl...@yahoo.com>>
Cc: "openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>" 
<openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>>
Sent: Friday, August 23, 2013 3:32 PM
Subject: RE: [Openstack] Baremetal - Hardware preparation

Please refer the hardware enrollment section under 
https://wiki.openstack.org/wiki/Baremetal.

1.      Ensure your hardware is under same network backbone to communicate
2.      Enroll the hardware properly as mentioned in the guide
3.      Nova baremetal driver will take care of the communication and you could 
see the logs in nova compute upon successful enrollment

Thanks
Shanthakumar K

From: Jake G. [mailto:dj_dark_jungl...@yahoo.com]
Sent: Friday, August 23, 2013 11:54 AM
To: K, Shanthakumar
Cc: openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>
Subject: Re: [Openstack] Baremetal - Hardware preparation

I understand your points and that is taken care of, but how exactly is 
Openstack going to connect to the hardware if the hardware has no OS and no IP?
How should the hardware be prepared so I can give Openstack the information it 
needs to enroll the hardware?

Thanks,
Jake



________________________________
From: "K, Shanthakumar" <shanthakuma...@hp.com<mailto:shanthakuma...@hp.com>>
To: Jake G. <dj_dark_jungl...@yahoo.com<mailto:dj_dark_jungl...@yahoo.com>>
Cc: "openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>" 
<openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>>
Sent: Friday, August 23, 2013 3:08 PM
Subject: RE: [Openstack] Baremetal - Hardware preparation

Hi Jake,

Your physical hardware should be maximum enough to support your OS 
configurations and  baremetal flavor you have created.

Ex:
1.       Your physical hardware should contain minimum configurations to run an 
operating system
2.       You need to take care of your Baremetal Flavor created WRT to your 
available hardware.


Thanks
Shanthakumar K

From: Jake G. [mailto:dj_dark_jungl...@yahoo.com]
Sent: Friday, August 23, 2013 10:07 AM
To: openstack@lists.openstack.org<mailto:openstack@lists.openstack.org>
Subject: [Openstack] Baremetal - Hardware preparation

Hi all,

I have been following this doc 
https://wiki.openstack.org/wiki/Baremetal#Image_Requirements
to setup openstack for baremetal provisioning. I have configured oopenstack 
properly, created an image,
and now I am ready to enroll my physical hardware. However, there seems to be 
no mention of how to
prepare my physical hardware.

Does anyone know what is required and what is the process to prepare my 
hardware?

Thank you for your help,
Jake


_______________________________________________
Mailing list: http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
Post to     : openstack@lists.openstack.org
Unsubscribe : http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack

Reply via email to