Hi there.
I need some help to find the root cause of my problems with
OpenOCD/JTAG interface/processor.
I have a brand new Olimex ARM-USM-TINY-H JTAG interface and a
Olimex LPC-H2148 prototype board. The board has been
programmed using the
built in boot loader and works but I can't get OpenOCD up and running.
I run WindowXP with OpenOCD 0.4.0 installed from the package assembled
by
by Freddie Chopin.
When I plug in the JTAG interface it is recoginized as 2 instances of
LibUSB-Win32 Devices
in the device mangager. The drivers are working properly according to
the dialog boxes. The
LED on the USB interface is not lit however. The LPC-H2148 is powered
from its USB interface and is recognized
as a CDC ACM port.
I then try to run OpenOCD the following happens:
C:\Documents and Settings\olof>openocd -f interface/olimex-arm-usb-tiny-
h.cfg -f
target/lpc2148.cfg
Open On-Chip Debugger 0.4.0 (2010-02-22-19:05)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.htmlRCLK - adaptive
jtag_nsrst_delay: 200
jtag_ntrst_delay: 200
trst_and_srst srst_pulls_trst srst_gates_jtag
trst_push_pull srst_open_drain
Info : max
TCK change to: 30000 kHz
Info : RCLK (adaptive clock speed)
Error: couldn't read enough bytes from FT2232 device (0 < 81)
Error: couldn't read from FT2232
Error: couldn't read enough bytes from FT2232 device (0 < 81)
Error: couldn't read from FT2232
Command handler execution failed
Warn : jtag initialization failed; try 'jtag init' again.
What does this mean? Is it the comunication with the JTAG interface
over USB that fails or is it
the comunication with the processor using JTAG that fails?
If is use telnet and log on to port 4444 and try 'jtag init' OpenOCD
says that init has already been run.
A full event list using -d 3 is shown below:
Open On-Chip Debugger 0.4.0 (2010-02-22-19:05)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
User : 10 0 command.c:539 command_print(): debug_level: 3
Debug: 11 0 configuration.c:45 add_script_search_dir(): adding C:
\Program\OpenOCD\0.4.0\bin\..
Debug: 12 0 configuration.c:45 add_script_search_dir(): adding C:
/Program/OpenOCD/0.4.0/bin/../share/openocd/scripts
Debug: 13 0 configuration.c:87 find_file(): found C:\Program\OpenOCD\0.
4.0\bin\../interface/olimex-arm-usb-tiny-h.cfg
Debug: 14 0 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_interface ft2232
Debug: 15 0 command.c:133 script_debug(): command - interface
ocd_interface ft2232
Debug: 17 0 command.c:346 register_command_handler(): registering
'ocd_ft2232_device_desc'...
Debug: 18 0 command.c:346 register_command_handler(): registering
'ocd_ft2232_serial'...
Debug: 19 0 command.c:346 register_command_handler(): registering
'ocd_ft2232_layout'...
Debug: 20 0 command.c:346 register_command_handler(): registering
'ocd_ft2232_vid_pid'...
Debug: 21 0 command.c:346 register_command_handler(): registering
'ocd_ft2232_latency'...
Debug: 22 0 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_ft2232_device_desc Olimex OpenOCD JTAG ARM-USB-
TINY-H
Debug: 23 16 command.c:133 script_debug(): command - ft2232_device_desc
ocd_ft2232_device_desc Olimex OpenOCD JTAG ARM-USB-TINY-H
Debug: 25 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_ft2232_layout olimex-jtag
Debug: 26 16 command.c:133 script_debug(): command - ft2232_layout
ocd_ft2232_layout olimex-jtag
Debug: 28 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_ft2232_vid_pid 0x15ba 0x002a
Debug: 29 16 command.c:133 script_debug(): command - ft2232_vid_pid
ocd_ft2232_vid_pid 0x15ba 0x002a
Debug: 31 16 configuration.c:87 find_file(): found C:\Program\OpenOCD\0.
4.0\bin\../target/lpc2148.cfg
Debug: 32 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag_rclk 500
Debug: 33 16 command.c:133 script_debug(): command - jtag_rclk
ocd_jtag_rclk 500
Debug: 35 16 core.c:1569 jtag_config_rclk(): handle jtag rclk
Debug: 36 16 core.c:1523 jtag_khz_to_speed(): convert khz to interface
specific speed value
User : 37 16 command.c:539 command_print(): RCLK - adaptive
Debug: 38 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag_nsrst_delay 200
Debug: 39 16 command.c:133 script_debug(): command - jtag_nsrst_delay
ocd_jtag_nsrst_delay 200
User : 41 16 command.c:539 command_print(): jtag_nsrst_delay: 200
Debug: 42 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag_ntrst_delay 200
Debug: 43 16 command.c:133 script_debug(): command - jtag_ntrst_delay
ocd_jtag_ntrst_delay 200
User : 45 16 command.c:539 command_print(): jtag_ntrst_delay: 200
Debug: 46 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_reset_config trst_and_srst srst_pulls_trst
Debug: 47 16 command.c:133 script_debug(): command - reset_config
ocd_reset_config trst_and_srst srst_pulls_trst
User : 49 16 command.c:539 command_print(): trst_and_srst
srst_pulls_trst srst_gates_jtag trst_push_pull srst_open_drain
Debug: 50 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag newtap lpc2148 cpu -irlen 4 -ircapture 0x1 -
irmask 0xf -expected-id 0x4f1f0f0f
Debug: 51 16 command.c:133 script_debug(): command - ocd_jtag ocd_jtag
newtap lpc2148 cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id
0x4f1f0f0f
Debug: 52 16 tcl.c:568 jim_newtap_cmd(): Creating New Tap, Chip:
lpc2148, Tap: cpu, Dotted: lpc2148.cpu, 8 params
Debug: 53 16 tcl.c:585 jim_newtap_cmd(): Processing option: -irlen
Debug: 54 16 tcl.c:585 jim_newtap_cmd(): Processing option: -ircapture
Debug: 55 16 tcl.c:585 jim_newtap_cmd(): Processing option: -irmask
Debug: 56 16 tcl.c:585 jim_newtap_cmd(): Processing option: -expected-
id
Debug: 57 16 core.c:1300 jtag_tap_init(): Created Tap: lpc2148.cpu @
abs position 0, irlen 4, capture: 0x1 mask: 0xf
Debug: 58 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_target create lpc2148.cpu arm7tdmi -endian little -
chain-position lpc2148.cpu -variant arm7tdmi-s_r4
Debug: 59 16 command.c:133 script_debug(): command - ocd_target
ocd_target create lpc2148.cpu arm7tdmi -endian little -chain-position
lpc2148.cpu -variant arm7tdmi-s_r4
Debug: 60 16 command.c:346 register_command_handler(): registering
'ocd_arm'...
Debug: 61 16 command.c:346 register_command_handler(): registering
'ocd_arm'...
Debug: 62 16 command.c:346 register_command_handler(): registering
'ocd_arm'...
Debug: 63 16 command.c:346 register_command_handler(): registering
'ocd_arm'...
Debug: 64 16 command.c:346 register_command_handler(): registering
'ocd_arm'...
Debug: 65 16 command.c:346 register_command_handler(): registering
'ocd_etm'...
Debug: 66 16 command.c:346 register_command_handler(): registering
'ocd_arm7_9'...
Debug: 67 16 command.c:346 register_command_handler(): registering
'ocd_arm7_9'...
Debug: 68 16 command.c:346 register_command_handler(): registering
'ocd_arm7_9'...
Debug: 69 16 command.c:346 register_command_handler(): registering
'ocd_arm7_9'...
Debug: 70 16 armv4_5.c:397 arm_set_cpsr(): set CPSR 0x00000010: User
mode, ARM state
Debug: 71 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 72 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 73 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 74 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 75 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 76 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 77 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 78 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 79 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 80 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 81 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 82 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 83 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 84 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 85 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 86 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 87 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 88 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 89 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 90 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 91 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 92 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 93 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 94 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 95 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 96 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 97 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 98 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 99 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 100 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 101 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 102 16 command.c:346 register_command_handler(): registering
'ocd_lpc2148.cpu'...
Debug: 103 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_lpc2148.cpu configure -work-area-phys 0x40000000 -
work-area-size 0x4000 -work-area-backup 0
Debug: 104 16 command.c:133 script_debug(): command - ocd_lpc2148.cpu
ocd_lpc2148.cpu configure -work-area-phys 0x40000000 -work-area-size
0x4000 -work-area-backup 0
Debug: 105 16 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_lpc2148.cpu configure -event reset-init
# Force target into ARM state
arm core_state arm
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
# "User Flash Mode" where interrupt vectors are _not_ remapped,
# and reside in flash instead).
#
# See section 7.1 on page 32 ("Memory Mapping control register") in
# "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006.
#
http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf
mwb 0xE01FC040 0x01
Debug: 106 16 command.c:133 script_debug():
command - ocd_lpc2148.cpu ocd_lpc2148.cpu configure -event reset-init
# Force target into ARM state
arm core_state arm
# Do not remap 0x0000-0x0020 to anything but the
flash (i.e. select
# "User Flash Mode" where interrupt vectors are _not_ remapped,
# and reside in flash instead).
#
# See section 7.1 on page 32 ("Memory Mapping control register") in
# "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006.
#
http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf
mwb 0xE01FC040 0x01
Debug: 107 16 command.c:133 script_debug():
command - ocd_command ocd_command type ocd_flash bank lpc2148.flash
lpc2000 0x0 0x7d000 0 0 lpc2148.cpu lpc2000_v2 14765 calc_checksum
Debug: 108 16 command.c:133 script_debug(): command - ocd_flash
ocd_flash bank lpc2148.flash lpc2000 0x0 0x7d000 0 0 lpc2148.cpu
lpc2000_v2 14765 calc_checksum
Debug: 110 16 command.c:346 register_command_handler(): registering
'ocd_lpc2000'...
Debug: 111 16 httpd_stubs.c:28 httpd_start(): libocdserver was built
without HTTPD support
Debug: 112 47 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_init
Debug: 113 47 command.c:133 script_debug(): command - init ocd_init
Debug: 115 47 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_target init
Debug: 116 47 command.c:133 script_debug(): command - ocd_target
ocd_target init
Debug: 118 47 target.c:835 handle_target_init_command(): Initializing
targets...
Debug: 119 47 command.c:346 register_command_handler(): registering
'ocd_target_request'...
Debug: 120 47 command.c:346 register_command_handler(): registering
'ocd_trace'...
Debug: 121 47 command.c:346 register_command_handler(): registering
'ocd_trace'...
Debug: 122 47 command.c:346 register_command_handler(): registering
'ocd_fast_load_image'...
Debug: 123 47 command.c:346 register_command_handler(): registering
'ocd_fast_load'...
Debug: 124 47 command.c:346 register_command_handler(): registering
'ocd_profile'...
Debug: 125 47 command.c:346 register_command_handler(): registering
'ocd_virt2phys'...
Debug: 126 47 command.c:346 register_command_handler(): registering
'ocd_reg'...
Debug: 127 47 command.c:346 register_command_handler(): registering
'ocd_poll'...
Debug: 128 47 command.c:346 register_command_handler(): registering
'ocd_wait_halt'...
Debug: 129 47 command.c:346 register_command_handler(): registering
'ocd_halt'...
Debug: 130 47 command.c:346 register_command_handler(): registering
'ocd_resume'...
Debug: 131 47 command.c:346 register_command_handler(): registering
'ocd_reset'...
Debug: 132 47 command.c:346 register_command_handler(): registering
'ocd_soft_reset_halt'...
Debug: 133 47 command.c:346 register_command_handler(): registering
'ocd_step'...
Debug: 134 47 command.c:346 register_command_handler(): registering
'ocd_mdw'...
Debug: 135 47 command.c:346 register_command_handler(): registering
'ocd_mdh'...
Debug: 136 47 command.c:346 register_command_handler(): registering
'ocd_mdb'...
Debug: 137 47 command.c:346 register_command_handler(): registering
'ocd_mww'...
Debug: 138 47 command.c:346 register_command_handler(): registering
'ocd_mwh'...
Debug: 139 47 command.c:346 register_command_handler(): registering
'ocd_mwb'...
Debug: 140 47 command.c:346 register_command_handler(): registering
'ocd_bp'...
Debug: 141 47 command.c:346 register_command_handler(): registering
'ocd_rbp'...
Debug: 142 47 command.c:346 register_command_handler(): registering
'ocd_wp'...
Debug: 143 47 command.c:346 register_command_handler(): registering
'ocd_rwp'...
Debug: 144 47 command.c:346 register_command_handler(): registering
'ocd_load_image'...
Debug: 145 47 command.c:346 register_command_handler(): registering
'ocd_dump_image'...
Debug: 146 47 command.c:346 register_command_handler(): registering
'ocd_verify_image'...
Debug: 147 47 command.c:346 register_command_handler(): registering
'ocd_test_image'...
Debug: 148 47 command.c:346 register_command_handler(): registering
'ocd_reset_nag'...
Debug: 149 47 ft2232.c:2097 ft2232_init(): ft2232 interface using
shortest path jtag state transitions
Debug: 150 47 ft2232.c:2011 ft2232_init_libftdi(): 'ft2232' interface
using libftdi with 'olimex-jtag' layout (15ba:002a)
Debug: 151 47 ft2232.c:2055 ft2232_init_libftdi(): current latency
timer: 2
Debug: 152 47 ft2232.c:2066 ft2232_init_libftdi(): FTDI chip type: 4
"2232H"
Debug: 153 47 ft2232.c:2443 olimex_jtag_init(): 80 08 1b
Debug: 154 47 ft2232.c:2487 olimex_jtag_init(): 82 09 0f
Info : 155 47 ft2232.c:494 ft2232h_ft4232h_clk_divide_by_5(): max TCK
change to: 30000 kHz
Debug: 156 47 core.c:1523 jtag_khz_to_speed(): convert khz to interface
specific speed value
Debug: 157 47 core.c:1527 jtag_khz_to_speed(): have interface set up
Debug: 158 47 ft2232.c:463 ft2232h_ft4232h_adaptive_clocking(): 96
Debug: 159 47 core.c:1523 jtag_khz_to_speed(): convert khz to interface
specific speed value
Debug: 160 47 core.c:1527 jtag_khz_to_speed(): have interface set up
Info : 161 47 core.c:1353 jtag_interface_init(): RCLK (adaptive clock
speed)
Debug: 162 47 openocd.c:122 handle_init_command(): jtag interface init
complete
Debug: 163 47 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag init
Debug: 164 47 command.c:133 script_debug(): command - ocd_jtag ocd_jtag
init
Debug: 166 47 tcl.c:854 handle_jtag_init_command(): Initializing jtag
devices...
Debug: 167 47 ft2232.c:1361 olimex_jtag_reset(): trst: 0, srst: 0,
high_output: 0x01, high_direction: 0x0f
Debug: 168 63 core.c:672 jtag_add_reset(): SRST line released
Debug: 169 63 core.c:697 jtag_add_reset(): TRST line released
Debug: 170 63 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Debug: 171 485 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag arp_init
Debug: 172 485 command.c:133 script_debug(): command - ocd_jtag
ocd_jtag arp_init
Debug: 173 485 core.c:1364 jtag_init_inner(): Init JTAG chain
Debug: 174 485 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Debug: 175 485 core.c:1017 jtag_examine_chain(): DR scan interrogation
for IDCODE/BYPASS
Debug: 176 485 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Error: 177 4485 ft2232.c:438 ft2232_read(): couldn't read enough bytes
from FT2232 device (0 < 81)
Error: 178 4485 ft2232.c:692 ft2232_send_and_recv(): couldn't read from
FT2232
Debug: 179 4485 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_jtag arp_init-reset
Debug: 180 4485 command.c:133 script_debug(): command - ocd_jtag
ocd_jtag arp_init-reset
Debug: 181 4485 core.c:1451 jtag_init_reset(): Initializing with hard
TRST+SRST reset
Debug: 182 4485 ft2232.c:1361 olimex_jtag_reset(): trst: 1, srst: 0,
high_output: 0x00, high_direction: 0x0f
Debug: 183 4485 core.c:692 jtag_add_reset(): TRST line asserted
Debug: 184 4485 ft2232.c:1361 olimex_jtag_reset(): trst: 1, srst: 1,
high_output: 0x0a, high_direction: 0x0f
Debug: 185 4485 core.c:667 jtag_add_reset(): SRST line asserted
Debug: 186 4485 ft2232.c:1361 olimex_jtag_reset(): trst: 0, srst: 0,
high_output: 0x01, high_direction: 0x0f
Debug: 187 4485 core.c:672 jtag_add_reset(): SRST line released
Debug: 188 4485 log.c:496 keep_alive(): keep_alive() was not invoked in
the 1000ms timelimit (4485). This may cause trouble with GDB
connections.
Debug: 190 4485 core.c:697 jtag_add_reset(): TRST line released
Debug: 191 4485 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Debug: 192 4907 core.c:1364 jtag_init_inner(): Init JTAG chain
Debug: 193 4907 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Debug: 194 4907 core.c:1017 jtag_examine_chain(): DR scan interrogation
for IDCODE/BYPASS
Debug: 195 4907 core.c:321 jtag_call_event_callbacks(): jtag event: TAP
reset
Error: 196 8907 ft2232.c:438 ft2232_read(): couldn't read enough bytes
from FT2232 device (0 < 81)
Error: 197 8907 ft2232.c:692 ft2232_send_and_recv(): couldn't read from
FT2232
Debug: 198 8907 command.c:620 run_command(): Command failed with error
code -4
User : 199 8907 command.c:824 openocd_jim_vfprintf(): Command handler
execution failed
User : 202 8907 command.c:824 openocd_jim_vfprintf():
User : 204 8907 command.c:824 openocd_jim_vfprintf():
Warn : 205 8907 openocd.c:137 handle_init_command(): jtag
initialization failed; try 'jtag init' again.
Debug: 206 8907 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_flash init
Debug: 207 8907 command.c:133 script_debug(): command - ocd_flash
ocd_flash init
Debug: 208 8907 log.c:496 keep_alive(): keep_alive() was not invoked in
the 1000ms timelimit (4422). This may cause trouble with GDB
connections.
Debug: 210 8907 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 212 8907 tcl.c:920 handle_flash_init_command(): Initializing
flash devices...
Debug: 213 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 214 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 215 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 216 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 217 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 218 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 219 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 220 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 221 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 222 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 223 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 224 8907 command.c:346 register_command_handler(): registering
'ocd_flash'...
Debug: 225 8907 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_mflash init
Debug: 226 8907 command.c:133 script_debug(): command - ocd_mflash
ocd_mflash init
Debug: 227 8907 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 229 8907 mflash.c:1325 handle_mflash_init_command():
Initializing mflash devices...
Debug: 230 8907 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_nand init
Debug: 231 8907 command.c:133 script_debug(): command - ocd_nand
ocd_nand init
Debug: 232 8907 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 234 8907 tcl.c:536 handle_nand_init_command(): Initializing NAND
devices...
Debug: 235 8907 command.c:133 script_debug(): command - ocd_command
ocd_command type ocd_pld init
Debug: 236 8907 command.c:133 script_debug(): command - ocd_pld ocd_pld
init
Debug: 237 8907 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 239 8907 pld.c:231 handle_pld_init_command(): Initializing
PLDs...
Debug: 240 8922 gdb_server.c:2370 gdb_target_start(): gdb service for
target 'lpc2148.cpu' on TCP port 3333
Debug: 241 9016 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 242 9219 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 243 9422 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 244 9625 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 245 9829 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 246 10016 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 247 10125 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 248 10329 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 249 10532 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 250 10719 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
Debug: 251 10829 target.c:968 target_call_event_callbacks(): target
event 2 (gdb-halt)
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
