Mike Christie wrote:
> Not exactly. iscsid.conf is used as the default settings for the
> node/portal records. When you run the iscsiadm discovery/new command
> then iscsiadm will create records in /etc/iscsi/nodes or
> /var/lib/iscsi/nodes (depends on the version) for each portal
> found/setup. When you run iscsiadm -m node -o show you are seeing those
> values in the db. When the iscsi service starts (when we login to a
> target), iscsiadm reads the db and uses those settings for each session.
> So some of those settings might be what we ask the target to use but we
> might end up negotiating some other value with the target.
Thanks for the helpful response. What about the iscsistart program which
dracut uses to get the initial connection? I assume this doesn't set these
settings, but does the iscsid which starts afterwards affect the connection
created by iscsistart?
>>> On the F16 system is iscsid running?
>>
>> Apparently (systemctl reports the service as running):
>> root 795 0.0 0.0 12908 656 ? Ss Nov30 0:01 iscsid
>> root 796 0.0 0.1 15796 5576 ? S<Ls Nov30 0:04 iscsid
>>
>
> So it is up. Could you send the /var/log/messages for when this happens?
It's broken again now The logs currently show:
Dec 2 09:58:56 xs2 kernel: [ 14.836794] Loading iSCSI transport class
v2.0-870.
Dec 2 09:58:56 xs2 kernel: [ 14.838084] iscsi: registered transport (tcp)
Dec 2 09:58:56 xs2 kernel: [ 14.903442] iscsistart (446):
/proc/446/oom_adj is deprecated, please use /proc/446/oom_score_adj instead.
Dec 2 09:58:56 xs2 kernel: [ 16.154330] scsi4 : iSCSI Initiator over
TCP/IP
Dec 2 09:58:56 xs2 kernel: [ 16.420384] scsi 4:0:0:0: RAID
IET Controller 0001 PQ: 0 ANSI: 5
Dec 2 09:58:56 xs2 kernel: [ 16.420685] scsi 4:0:0:0: Attached scsi
generic sg0 type 12
Dec 2 09:58:56 xs2 kernel: [ 16.421884] scsi 4:0:0:1: Direct-Access
IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5
Dec 2 09:58:56 xs2 kernel: [ 16.422189] sd 4:0:0:1: Attached scsi generic
sg1 type 0
Dec 2 09:58:56 xs2 kernel: [ 16.423111] sd 4:0:0:1: [sda] 33204224 512-
byte logical blocks: (17.0 GB/15.8 GiB)
Dec 2 09:58:56 xs2 kernel: [ 16.425964] sd 4:0:0:1: [sda] Write Protect
is off
Dec 2 09:58:56 xs2 kernel: [ 16.426701] sd 4:0:0:1: [sda] Write cache:
enabled, read cache: enabled, doesn't support DPO or FUA
Dec 2 09:58:56 xs2 kernel: [ 16.450444] sda: unknown partition table
Dec 2 09:58:56 xs2 kernel: [ 16.452808] sd 4:0:0:1: [sda] Attached SCSI
disk
Dec 2 09:58:56 xs2 kernel: [ 16.991839] EXT4-fs (sda): mounted filesystem
with ordered data mode. Opts: (null)
iscsid isn't running. If I try "service iscsid restart" it doesn't start,
though running iscsd by hand works. I also tried the init script "force-
start" option which does work.
I think this is because the Fedora 16 init script for iscsid isn't properly
detecting that the root is on iscsi. It does
# FIXME this has a false positive for root on nfs
root_is_iscsi() {
rootopts=$(awk '{ if ($1 !~ /^[ \t]*#/ && $2 == "/") { print $4; }}'
/etc/mtab)
[[ "$rootopts" =~ "_netdev" ]]
}
/etc/mtab is now linked to /proc/mounts, so this doesn't have the _netdev
option, even if fstab has this. I think something like "findmnt -m /" is
meant to be used instead.
There's some discussion on the fedora-devel list for similar issues in this
thread:
http://lists.fedoraproject.org/pipermail/devel/2011-November/160025.html
Jeremy
--
You received this message because you are subscribed to the Google Groups
"open-iscsi" group.
To post to this group, send email to [email protected].
To unsubscribe from this group, send email to
[email protected].
For more options, visit this group at
http://groups.google.com/group/open-iscsi?hl=en.
