Hi Asnat, KK is referring to the output that you get on the console when you start nox_core in verbose mode (using "-v"). When you get the 'connection failed/dropped' messages on the switch side, you'll get some corresponding log messages on NOX's console; that's what we're looking for.
On Sun, Dec 5, 2010 at 8:38 PM, Hasnat Ahmed <10msithah...@seecs.edu.pk>wrote: > Hi kk, > > can you tell me how to view the nox logs...where its being placed ... > > thanks > > Regards > Hasnat > > > On Sat, Dec 4, 2010 at 11:22 PM, kk yap <yap...@stanford.edu> wrote: > >> Hi Hasnat, >> >> You are not telling me much other than you have some errors going on. >> It would definitely help if you can tell me what the errors are. Then >> maybe I can see if I can advise on how to get rid of them. So, can I >> have the logs? Thanks. >> >> Regards >> KK >> >> PS>> Unless this is meant to be a private email, please don't drop the >> mailing list. Thanks. >> >> On 4 December 2010 06:39, Hasnat Ahmed <10msithah...@seecs.edu.pk> wrote: >> > now i have redone all the steps mentioned in "CREATE AN OPENFLOW NETWORK >> > WITHIN A SINGLE PC" my switch portion is verified successfully and >> drawing >> > command is also working fine but this time at controller(NOX) portion >> when i >> > run the ./nox_core -i ptcp:6633 routing command >> > it is displaying me that line "openflow compiled" and cursor stays blink >> > like its in blocking stage etc i dont know >> > >> > than when i run a command vms-start.py 2hosts-2ofsw.vms.xml >> > its shows me error "hda.disk " file is missing. but i have placed this >> file >> > and its present. >> > >> > On Wed, Dec 1, 2010 at 6:18 PM, kk yap <yap...@stanford.edu> wrote: >> >> >> >> I see the errors on the switch side, but what about the NOX side? >> >> What is the controller saying about the switch? Is the switch >> >> disconnecting or is the controller disconnecting the switch? That's >> >> critical for understanding what is happening. >> >> >> >> Regards >> >> KK >> >> >> >> On 1 December 2010 03:22, Hasnat Ahmed <10msithah...@seecs.edu.pk> >> wrote: >> >> > sorry yapkke , i did not get ur point. >> >> > >> >> > On Wed, Dec 1, 2010 at 11:57 AM, kk yap <yap...@stanford.edu> wrote: >> >> >> >> >> >> What about the log from the NOX side of things? >> >> >> >> >> >> Regards >> >> >> KK >> >> >> >> >> >> On 30 November 2010 22:49, Hasnat Ahmed <10msithah...@seecs.edu.pk> >> >> >> wrote: >> >> >> > Hi , while creating a openflow network within a single pc I have >> >> >> > verified >> >> >> > successfully switch set up part but when tried to setup the >> >> >> > controller >> >> >> > portion. we are examing a issue. controller port (6663) is in >> >> >> > listening >> >> >> > mode >> >> >> > (fine)but when we start the controller it will 1st show its status >> >> >> > connected >> >> >> > and then lose the connection and cannot reestablish the >> connection. >> >> >> > so >> >> >> > without holding the conntroller connectivity the simulation cant >> run. >> >> >> > >> >> >> > kindly see the attached pic. >> >> >> > >> >> >> > we are not getting out that why controller loses its connectivity. >> >> >> > >> >> >> > >> >> >> > >> >> >> > >> >> >> > >> >> >> > >> >> >> > _______________________________________________ >> >> >> > nox-dev mailing list >> >> >> > nox-dev@noxrepo.org >> >> >> > http://noxrepo.org/mailman/listinfo/nox-dev_noxrepo.org >> >> >> > >> >> >> > >> >> > >> >> > >> > >> > >> > > > _______________________________________________ > nox-dev mailing list > nox-dev@noxrepo.org > http://noxrepo.org/mailman/listinfo/nox-dev_noxrepo.org > >
_______________________________________________ nox-dev mailing list nox-dev@noxrepo.org http://noxrepo.org/mailman/listinfo/nox-dev_noxrepo.org
