On Fri, 2021-04-09 at 21:18 +0200, Heiner Kallweit wrote:
> On 09.04.2021 20:41, Radu Pirea (NXP OSS) wrote:
> > Add driver for tja1103 driver and for future NXP C45 PHYs.
> >
> > Signed-off-by: Radu Pirea (NXP OSS)
> > <radu-nicolae.pi...@oss.nxp.com>
> > ---
> > MAINTAINERS | 6 +
> > drivers/net/phy/Kconfig | 6 +
> > drivers/net/phy/Makefile | 1 +
> > drivers/net/phy/nxp-c45.c | 622
> > ++++++++++++++++++++++++++++++++++++++
> > 4 files changed, 635 insertions(+)
> > create mode 100644 drivers/net/phy/nxp-c45.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index a008b70f3c16..082a5eca8913 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -12518,6 +12518,12 @@ F: drivers/nvmem/
> > F: include/linux/nvmem-consumer.h
> > F: include/linux/nvmem-provider.h
> >
> > +NXP C45 PHY DRIVER
> > +M: Radu Pirea <radu-nicolae.pi...@oss.nxp.com>
> > +L: netdev@vger.kernel.org
> > +S: Maintained
> > +F: drivers/net/phy/nxp-c45.c
> > +
> > NXP FSPI DRIVER
> > M: Ashish Kumar <ashish.ku...@nxp.com>
> > R: Yogesh Gaur <yogeshgaur...@gmail.com>
> > diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> > index 698bea312adc..fd2da80b5339 100644
> > --- a/drivers/net/phy/Kconfig
> > +++ b/drivers/net/phy/Kconfig
> > @@ -228,6 +228,12 @@ config NATIONAL_PHY
> > help
> > Currently supports the DP83865 PHY.
> >
> > +config NXP_C45_PHY
> > + tristate "NXP C45 PHYs"
> > + help
> > + Enable support for NXP C45 PHYs.
> > + Currently supports only the TJA1103 PHY.
> > +
> > config NXP_TJA11XX_PHY
> > tristate "NXP TJA11xx PHYs support"
> > depends on HWMON
> > diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> > index a13e402074cf..a18f095748b5 100644
> > --- a/drivers/net/phy/Makefile
> > +++ b/drivers/net/phy/Makefile
> > @@ -70,6 +70,7 @@ obj-$(CONFIG_MICROCHIP_PHY) += microchip.o
> > obj-$(CONFIG_MICROCHIP_T1_PHY) += microchip_t1.o
> > obj-$(CONFIG_MICROSEMI_PHY) += mscc/
> > obj-$(CONFIG_NATIONAL_PHY) += national.o
> > +obj-$(CONFIG_NXP_C45_PHY) += nxp-c45.o
> > obj-$(CONFIG_NXP_TJA11XX_PHY) += nxp-tja11xx.o
> > obj-$(CONFIG_QSEMI_PHY) += qsemi.o
> > obj-$(CONFIG_REALTEK_PHY) += realtek.o
> > diff --git a/drivers/net/phy/nxp-c45.c b/drivers/net/phy/nxp-c45.c
> > new file mode 100644
> > index 000000000000..2961799f7d05
> > --- /dev/null
> > +++ b/drivers/net/phy/nxp-c45.c
> > @@ -0,0 +1,622 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* NXP C45 PHY driver
> > + * Copyright (C) 2021 NXP
> > + * Copyright (C) 2021 Radu Pirea <radu-nicolae.pi...@oss.nxp.com>
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/ethtool.h>
> > +#include <linux/ethtool_netlink.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mii.h>
> > +#include <linux/module.h>
> > +#include <linux/phy.h>
> > +#include <linux/processor.h>
> > +#include <linux/property.h>
> > +
> > +#define PHY_ID_BASE_T1 0x001BB010
> > +
> > +#define B100T1_PMAPMD_CTL 0x0834
> > +#define B100T1_PMAPMD_CONFIG_EN BIT(15)
> > +#define B100T1_PMAPMD_MASTER BIT(14)
> > +#define MASTER_MODE (B100T1_PMAPMD_CONFIG_EN |
> > B100T1_PMAPMD_MASTER)
> > +#define SLAVE_MODE (B100T1_PMAPMD_CONFIG_EN)
> > +
> > +#define DEVICE_CONTROL 0x0040
> > +#define DEVICE_CONTROL_RESET BIT(15)
> > +#define DEVICE_CONTROL_CONFIG_GLOBAL_EN BIT(14)
> > +#define DEVICE_CONTROL_CONFIG_ALL_EN BIT(13)
> > +#define RESET_POLL_NS (250 * NSEC_PER_MSEC)
> > +
> > +#define PHY_CONTROL 0x8100
> > +#define PHY_CONFIG_EN BIT(14)
> > +#define PHY_START_OP BIT(0)
> > +
> > +#define PHY_CONFIG 0x8108
> > +#define PHY_CONFIG_AUTO BIT(0)
> > +
> > +#define SIGNAL_QUALITY 0x8320
> > +#define SQI_VALID BIT(14)
> > +#define SQI_MASK GENMASK(2, 0)
> > +#define MAX_SQI SQI_MASK
> > +
> > +#define CABLE_TEST 0x8330
> > +#define CABLE_TEST_ENABLE BIT(15)
> > +#define CABLE_TEST_START BIT(14)
> > +#define CABLE_TEST_VALID BIT(13)
> > +#define CABLE_TEST_OK 0x00
> > +#define CABLE_TEST_SHORTED 0x01
> > +#define CABLE_TEST_OPEN 0x02
> > +#define CABLE_TEST_UNKNOWN 0x07
> > +
> > +#define PORT_CONTROL 0x8040
> > +#define PORT_CONTROL_EN BIT(14)
> > +
> > +#define PORT_INFRA_CONTROL 0xAC00
> > +#define PORT_INFRA_CONTROL_EN BIT(14)
> > +
> > +#define VND1_RXID 0xAFCC
> > +#define VND1_TXID 0xAFCD
> > +#define ID_ENABLE BIT(15)
> > +
> > +#define ABILITIES 0xAFC4
> > +#define RGMII_ID_ABILITY BIT(15)
> > +#define RGMII_ABILITY BIT(14)
> > +#define RMII_ABILITY BIT(10)
> > +#define REVMII_ABILITY BIT(9)
> > +#define MII_ABILITY BIT(8)
> > +#define SGMII_ABILITY BIT(0)
> > +
> > +#define MII_BASIC_CONFIG 0xAFC6
> > +#define MII_BASIC_CONFIG_REV BIT(8)
> > +#define MII_BASIC_CONFIG_SGMII 0x9
> > +#define MII_BASIC_CONFIG_RGMII 0x7
> > +#define MII_BASIC_CONFIG_RMII 0x5
> > +#define MII_BASIC_CONFIG_MII 0x4
> > +
> > +#define SYMBOL_ERROR_COUNTER 0x8350
> > +#define LINK_DROP_COUNTER 0x8352
> > +#define LINK_LOSSES_AND_FAILURES 0x8353
> > +#define R_GOOD_FRAME_CNT 0xA950
> > +#define R_BAD_FRAME_CNT 0xA952
> > +#define R_RXER_FRAME_CNT 0xA954
> > +#define RX_PREAMBLE_COUNT 0xAFCE
> > +#define TX_PREAMBLE_COUNT 0xAFCF
> > +#define RX_IPG_LENGTH 0xAFD0
> > +#define TX_IPG_LENGTH 0xAFD1
> > +#define COUNTERS_EN BIT(15)
> > +
> > +#define CLK_25MHZ_PS_PERIOD 40000UL
> > +#define PS_PER_DEGREE (CLK_25MHZ_PS_PERIOD / 360)
> > +#define MIN_ID_PS 8222U
> > +#define MAX_ID_PS 11300U
> > +
> > +struct nxp_c45_phy {
> > + u32 tx_delay;
> > + u32 rx_delay;
> > +};
> > +
> > +struct nxp_c45_phy_stats {
> > + const char *name;
> > + u8 mmd;
> > + u16 reg;
> > + u8 off;
> > + u16 mask;
> > +};
> > +
> > +static const struct nxp_c45_phy_stats nxp_c45_hw_stats[] = {
> > + { "phy_symbol_error_cnt", MDIO_MMD_VEND1,
> > SYMBOL_ERROR_COUNTER, 0, GENMASK(15, 0) },
> > + { "phy_link_status_drop_cnt", MDIO_MMD_VEND1,
> > LINK_DROP_COUNTER, 8, GENMASK(13, 8) },
> > + { "phy_link_availability_drop_cnt", MDIO_MMD_VEND1,
> > LINK_DROP_COUNTER, 0, GENMASK(5, 0) },
> > + { "phy_link_loss_cnt", MDIO_MMD_VEND1,
> > LINK_LOSSES_AND_FAILURES, 10, GENMASK(15, 10) },
> > + { "phy_link_failure_cnt", MDIO_MMD_VEND1,
> > LINK_LOSSES_AND_FAILURES, 0, GENMASK(9, 0) },
> > + { "r_good_frame_cnt", MDIO_MMD_VEND1, R_GOOD_FRAME_CNT, 0,
> > GENMASK(15, 0) },
> > + { "r_bad_frame_cnt", MDIO_MMD_VEND1, R_BAD_FRAME_CNT, 0,
> > GENMASK(15, 0) },
> > + { "r_rxer_frame_cnt", MDIO_MMD_VEND1, R_RXER_FRAME_CNT, 0,
> > GENMASK(15, 0) },
> > + { "rx_preamble_count", MDIO_MMD_VEND1, RX_PREAMBLE_COUNT,
> > 0, GENMASK(5, 0) },
> > + { "tx_preamble_count", MDIO_MMD_VEND1, TX_PREAMBLE_COUNT,
> > 0, GENMASK(5, 0) },
> > + { "rx_ipg_length", MDIO_MMD_VEND1, RX_IPG_LENGTH, 0,
> > GENMASK(8, 0) },
> > + { "tx_ipg_length", MDIO_MMD_VEND1, TX_IPG_LENGTH, 0,
> > GENMASK(8, 0) },
> > +};
> > +
> > +static int nxp_c45_get_sset_count(struct phy_device *phydev)
> > +{
> > + return ARRAY_SIZE(nxp_c45_hw_stats);
> > +}
> > +
> > +static void nxp_c45_get_strings(struct phy_device *phydev, u8
> > *data)
> > +{
> > + size_t i;
> > +
> > + for (i = 0; i < ARRAY_SIZE(nxp_c45_hw_stats); i++) {
> > + strncpy(data + i * ETH_GSTRING_LEN,
> > + nxp_c45_hw_stats[i].name, ETH_GSTRING_LEN);
> > + }
> > +}
> > +
> > +static void nxp_c45_get_stats(struct phy_device *phydev,
> > + struct ethtool_stats *stats, u64
> > *data)
> > +{
> > + size_t i;
> > + int ret;
> > +
> > + for (i = 0; i < ARRAY_SIZE(nxp_c45_hw_stats); i++) {
> > + ret = phy_read_mmd(phydev, nxp_c45_hw_stats[i].mmd,
> > nxp_c45_hw_stats[i].reg);
> > + if (ret < 0) {
> > + data[i] = U64_MAX;
> > + } else {
> > + data[i] = ret & nxp_c45_hw_stats[i].mask;
> > + data[i] >>= nxp_c45_hw_stats[i].off;
> > + }
> > + }
> > +}
> > +
> > +static int nxp_c45_config_enable(struct phy_device *phydev)
> > +{
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, DEVICE_CONTROL,
> > DEVICE_CONTROL_CONFIG_GLOBAL_EN |
> > + DEVICE_CONTROL_CONFIG_ALL_EN);
> > + usleep_range(400, 450);
> > +
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, PORT_CONTROL,
> > PORT_CONTROL_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, PHY_CONTROL,
> > PHY_CONFIG_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, PORT_INFRA_CONTROL,
> > PORT_INFRA_CONTROL_EN);
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_start_op(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, PHY_CONTROL);
> > + reg |= PHY_START_OP;
> > +
> > + return phy_write_mmd(phydev, MDIO_MMD_VEND1, PHY_CONTROL,
> > reg);
>
> You may want to use phy_set_bits_mmd() here. Similar comment
> applies to other places in the driver where phy_clear_bits_mmd()
> and phy_modify_mmd() could be used.
Thank you for suggestion. I will consider this.
>
> > +}
> > +
> > +static bool nxp_c45_can_sleep(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_STAT1);
> > + if (reg < 0)
> > + return false;
> > +
> > + return !!(reg & MDIO_STAT1_LPOWERABLE);
> > +}
> > +
> > +static int nxp_c45_resume(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + if (!nxp_c45_can_sleep(phydev))
> > + return -EOPNOTSUPP;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1);
> > + reg &= ~MDIO_CTRL1_LPOWER;
> > + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1, reg);
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_suspend(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + if (!nxp_c45_can_sleep(phydev))
> > + return -EOPNOTSUPP;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1);
> > + reg |= MDIO_CTRL1_LPOWER;
> > + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1, reg);
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_reset_done(struct phy_device *phydev)
> > +{
> > + return !(phy_read_mmd(phydev, MDIO_MMD_VEND1,
> > DEVICE_CONTROL) & DEVICE_CONTROL_RESET);
> > +}
> > +
> > +static int nxp_c45_reset_done_or_timeout(struct phy_device
> > *phydev,
> > + ktime_t timeout)
> > +{
> > + ktime_t cur = ktime_get();
> > +
> > + return nxp_c45_reset_done(phydev) || ktime_after(cur,
> > timeout);
> > +}
> > +
> > +static int nxp_c45_soft_reset(struct phy_device *phydev)
> > +{
> > + ktime_t timeout;
> > + int ret;
> > +
> > + ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, DEVICE_CONTROL,
> > DEVICE_CONTROL_RESET);
> > + if (ret)
> > + return ret;
> > +
> > + timeout = ktime_add_ns(ktime_get(), RESET_POLL_NS);
> > + spin_until_cond(nxp_c45_reset_done_or_timeout(phydev,
> > timeout));
> > + if (!nxp_c45_reset_done(phydev)) {
> > + phydev_err(phydev, "reset fail\n");
> > + return -EIO;
> > + }
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_cable_test_start(struct phy_device *phydev)
> > +{
> > + return phy_write_mmd(phydev, MDIO_MMD_VEND1, CABLE_TEST,
> > + CABLE_TEST_ENABLE | CABLE_TEST_START);
> > +}
> > +
> > +static int nxp_c45_cable_test_get_status(struct phy_device
> > *phydev,
> > + bool *finished)
> > +{
> > + int ret;
> > + u8 cable_test_result;
> > +
> > + ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, CABLE_TEST);
> > + if (!(ret & CABLE_TEST_VALID)) {
> > + *finished = false;
> > + return 0;
> > + }
> > +
> > + *finished = true;
> > + cable_test_result = ret & GENMASK(2, 0);
> > +
> > + switch (cable_test_result) {
> > + case CABLE_TEST_OK:
> > + ethnl_cable_test_result(phydev,
> > ETHTOOL_A_CABLE_PAIR_A,
> > + ETHTOOL_A_CABLE_RESULT_CODE
> > _OK);
> > + break;
> > + case CABLE_TEST_SHORTED:
> > + ethnl_cable_test_result(phydev,
> > ETHTOOL_A_CABLE_PAIR_A,
> > + ETHTOOL_A_CABLE_RESULT_CODE
> > _SAME_SHORT);
> > + break;
> > + case CABLE_TEST_OPEN:
> > + ethnl_cable_test_result(phydev,
> > ETHTOOL_A_CABLE_PAIR_A,
> > + ETHTOOL_A_CABLE_RESULT_CODE
> > _OPEN);
> > + break;
> > + default:
> > + ethnl_cable_test_result(phydev,
> > ETHTOOL_A_CABLE_PAIR_A,
> > + ETHTOOL_A_CABLE_RESULT_CODE
> > _UNSPEC);
> > + }
> > +
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, CABLE_TEST, 0);
> > +
> > + return nxp_c45_start_op(phydev);
> > +}
> > +
> > +static int nxp_c45_setup_master_slave(struct phy_device *phydev)
> > +{
> > + switch (phydev->master_slave_set) {
> > + case MASTER_SLAVE_CFG_MASTER_FORCE:
> > + case MASTER_SLAVE_CFG_MASTER_PREFERRED:
> > + phy_write_mmd(phydev, MDIO_MMD_PMAPMD,
> > B100T1_PMAPMD_CTL, MASTER_MODE);
> > + break;
> > + case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
> > + case MASTER_SLAVE_CFG_SLAVE_FORCE:
> > + phy_write_mmd(phydev, MDIO_MMD_PMAPMD,
> > B100T1_PMAPMD_CTL, SLAVE_MODE);
> > + break;
> > + case MASTER_SLAVE_CFG_UNKNOWN:
> > + case MASTER_SLAVE_CFG_UNSUPPORTED:
> > + return 0;
> > + default:
> > + phydev_warn(phydev, "Unsupported Master/Slave
> > mode\n");
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_read_master_slave(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + phydev->master_slave_get = MASTER_SLAVE_CFG_UNKNOWN;
> > + phydev->master_slave_state = MASTER_SLAVE_STATE_UNKNOWN;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_PMAPMD,
> > B100T1_PMAPMD_CTL);
> > + if (reg < 0)
> > + return reg;
> > +
> > + if (reg & B100T1_PMAPMD_MASTER) {
> > + phydev->master_slave_get =
> > MASTER_SLAVE_CFG_MASTER_FORCE;
> > + phydev->master_slave_state =
> > MASTER_SLAVE_STATE_MASTER;
> > + } else {
> > + phydev->master_slave_get =
> > MASTER_SLAVE_CFG_SLAVE_FORCE;
> > + phydev->master_slave_state =
> > MASTER_SLAVE_STATE_SLAVE;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_config_aneg(struct phy_device *phydev)
> > +{
> > + return nxp_c45_setup_master_slave(phydev);
> > +}
> > +
> > +static int nxp_c45_read_status(struct phy_device *phydev)
> > +{
> > + int ret;
> > +
> > + ret = genphy_c45_read_status(phydev);
> > + if (ret)
> > + return ret;
> > +
> > + ret = nxp_c45_read_master_slave(phydev);
> > + if (ret)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_set_loopback(struct phy_device *phydev, bool
> > enable)
> > +{
> > + int reg;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1);
> > + if (reg < 0)
> > + return reg;
> > +
> > + if (enable)
> > + reg |= MDIO_PCS_CTRL1_LOOPBACK;
> > + else
> > + reg &= ~MDIO_PCS_CTRL1_LOOPBACK;
> > +
> > + phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1, reg);
> > +
> > + phydev->loopback_enabled = enable;
> > +
> > + phydev_dbg(phydev, "Loopback %s\n", enable ? "enabled" :
> > "disabled");
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_get_sqi(struct phy_device *phydev)
> > +{
> > + int reg;
> > +
> > + reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, SIGNAL_QUALITY);
> > + if (!(reg & SQI_VALID))
> > + return -EINVAL;
> > +
> > + reg &= SQI_MASK;
> > +
> > + return reg;
> > +}
> > +
> > +static int nxp_c45_get_sqi_max(struct phy_device *phydev)
> > +{
> > + return MAX_SQI;
> > +}
> > +
> > +static int nxp_c45_check_delay(struct phy_device *phydev, u32
> > delay)
> > +{
> > + if (delay < MIN_ID_PS) {
> > + phydev_err(phydev, "delay value smaller than %u\n",
> > MIN_ID_PS);
> > + return -EINVAL;
> > + }
> > +
> > + if (delay > MAX_ID_PS) {
> > + phydev_err(phydev, "delay value higher than %u\n",
> > MAX_ID_PS);
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static u64 nxp_c45_get_phase_shift(u64 phase_offset_raw)
> > +{
> > + /* The delay in degree phase is 73.8 + phase_offset_raw *
> > 0.9.
> > + * To avoid floating point operations we'll multiply by 10
> > + * and get 1 decimal point precision.
> > + */
> > + phase_offset_raw *= 10;
> > + return (phase_offset_raw - 738) / 9;
> > +}
> > +
> > +static void nxp_c45_set_delays(struct phy_device *phydev)
> > +{
> > + struct nxp_c45_phy *priv = phydev->priv;
> > + u64 tx_delay = priv->tx_delay;
> > + u64 rx_delay = priv->rx_delay;
> > + u64 degree;
> > +
> > + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> > + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
> > + degree = tx_delay / PS_PER_DEGREE;
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, VND1_TXID,
> > + ID_ENABLE |
> > nxp_c45_get_phase_shift(degree));
> > + }
> > +
> > + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> > + phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
> > + degree = rx_delay / PS_PER_DEGREE;
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, VND1_RXID,
> > + ID_ENABLE |
> > nxp_c45_get_phase_shift(degree));
> > + }
> > +}
> > +
> > +static int nxp_c45_get_delays(struct phy_device *phydev)
> > +{
> > + struct nxp_c45_phy *priv = phydev->priv;
> > + int ret;
> > +
> > + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> > + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
> > + ret = device_property_read_u32(&phydev->mdio.dev,
> > "tx-internal-delay-ps",
> > + &priv->tx_delay);
> > + if (ret) {
> > + phydev_err(phydev, "tx-internal-delay-ps
> > property missing\n");
> > + return ret;
> > + }
> > + ret = nxp_c45_check_delay(phydev, priv->tx_delay);
> > + if (ret) {
> > + phydev_err(phydev, "tx-internal-delay-ps
> > invalid value\n");
> > + return ret;
> > + }
> > + }
> > +
> > + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> > + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
> > + ret = device_property_read_u32(&phydev->mdio.dev,
> > "rx-internal-delay-ps",
> > + &priv->rx_delay);
> > + if (ret) {
> > + phydev_err(phydev, "rx-internal-delay-ps
> > property missing\n");
> > + return ret;
> > + }
> > + ret = nxp_c45_check_delay(phydev, priv->rx_delay);
> > + if (ret) {
> > + phydev_err(phydev, "rx-internal-delay-ps
> > invalid value\n");
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_set_phy_mode(struct phy_device *phydev)
> > +{
> > + int ret;
> > +
> > + ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, ABILITIES);
> > + phydev_dbg(phydev, "Clause 45 managed PHY abilities
> > 0x%x\n", ret);
> > +
> > + switch (phydev->interface) {
> > + case PHY_INTERFACE_MODE_RGMII:
> > + if (!(ret & RGMII_ABILITY)) {
> > + phydev_err(phydev, "rgmii mode not
> > supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_RGMII);
> > + break;
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > + if (!(ret & RGMII_ID_ABILITY)) {
> > + phydev_err(phydev, "rgmii-id, rgmii-txid,
> > rgmii-rxid modes are not supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_RGMII);
> > + ret = nxp_c45_get_delays(phydev);
> > + if (ret)
> > + return ret;
> > +
> > + nxp_c45_set_delays(phydev);
> > + break;
> > + case PHY_INTERFACE_MODE_MII:
> > + if (!(ret & MII_ABILITY)) {
> > + phydev_err(phydev, "mii mode not
> > supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_MII);
> > + break;
> > + case PHY_INTERFACE_MODE_REVMII:
> > + if (!(ret & REVMII_ABILITY)) {
> > + phydev_err(phydev, "rev-mii mode not
> > supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_MII |
> > + MII_BASIC_CONFIG_REV);
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + if (!(ret & RMII_ABILITY)) {
> > + phydev_err(phydev, "rmii mode not
> > supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_RMII);
> > + break;
> > + case PHY_INTERFACE_MODE_SGMII:
> > + if (!(ret & SGMII_ABILITY)) {
> > + phydev_err(phydev, "sgmii mode not
> > supported\n");
> > + return -EINVAL;
> > + }
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1,
> > MII_BASIC_CONFIG, MII_BASIC_CONFIG_SGMII);
> > + break;
> > + case PHY_INTERFACE_MODE_INTERNAL:
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int nxp_c45_config_init(struct phy_device *phydev)
> > +{
> > + int ret;
> > +
> > + ret = nxp_c45_config_enable(phydev);
> > + if (ret) {
> > + phydev_err(phydev, "Failed to enable config\n");
> > + return ret;
> > + }
> > +
> > + ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, PHY_CONFIG);
> > + ret &= ~PHY_CONFIG_AUTO;
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, PHY_CONFIG, ret);
> > +
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, LINK_DROP_COUNTER,
> > COUNTERS_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, RX_PREAMBLE_COUNT,
> > COUNTERS_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, TX_PREAMBLE_COUNT,
> > COUNTERS_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, RX_IPG_LENGTH,
> > COUNTERS_EN);
> > + phy_write_mmd(phydev, MDIO_MMD_VEND1, TX_IPG_LENGTH,
> > COUNTERS_EN);
> > +
> > + ret = nxp_c45_set_phy_mode(phydev);
> > + if (ret)
> > + return ret;
> > +
> > + phydev->autoneg = AUTONEG_DISABLE;
> > +
> > + return nxp_c45_start_op(phydev);
> > +}
> > +
> > +static int nxp_c45_probe(struct phy_device *phydev)
> > +{
> > + struct nxp_c45_phy *priv;
> > +
> > + priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv),
> > GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + phydev->priv = priv;
> > +
> > + return 0;
> > +}
> > +
> > +static struct phy_driver nxp_c45_driver[] = {
> > + {
> > + PHY_ID_MATCH_MODEL(PHY_ID_BASE_T1),
> > + .name = "NXP C45 BASE-T1",
> > + .features = PHY_BASIC_T1_FEATURES,
> > + .probe = nxp_c45_probe,
> > + .soft_reset = nxp_c45_soft_reset,
> > + .config_aneg = nxp_c45_config_aneg,
> > + .config_init = nxp_c45_config_init,
> > + .read_status = nxp_c45_read_status,
> > + .suspend = nxp_c45_suspend,
> > + .resume = nxp_c45_resume,
> > + .get_sset_count = nxp_c45_get_sset_count,
> > + .get_strings = nxp_c45_get_strings,
> > + .get_stats = nxp_c45_get_stats,
> > + .cable_test_start = nxp_c45_cable_test_start,
> > + .cable_test_get_status =
> > nxp_c45_cable_test_get_status,
> > + .set_loopback = nxp_c45_set_loopback,
> > + .get_sqi = nxp_c45_get_sqi,
> > + .get_sqi_max = nxp_c45_get_sqi_max,
>
> How about interrupt support?
Unfortunately my setup is a bit limited and I can't test the
interrupts. However, I am planning to add interrupt support in a
further patch.
>
> > + },
> > +};
> > +
> > +module_phy_driver(nxp_c45_driver);
> > +
> > +static struct mdio_device_id __maybe_unused nxp_c45_tbl[] = {
> > + { PHY_ID_MATCH_MODEL(PHY_ID_BASE_T1) }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(mdio, nxp_c45_tbl);
> > +
> > +MODULE_AUTHOR("Radu Pirea <radu-nicolae.pi...@oss.nxp.com>");
> > +MODULE_DESCRIPTION("NXP C45 PHY driver");
> > +MODULE_LICENSE("GPL v2");
> >
> Re: [PATCH] phy: nxp-c45: add driver for tja1103
Radu Nicolae Pirea (NXP OSS) Mon, 12 Apr 2021 02:13:03 -0700
- [PATCH] phy: nxp-c45: add driver for tja1103 Radu Pirea (NXP OSS)
- Re: [PATCH] phy: nxp-c45: add driver for... Heiner Kallweit
- Re: [PATCH] phy: nxp-c45: add driver... Radu Nicolae Pirea (NXP OSS)
- Re: [PATCH] phy: nxp-c45: add driver for... Jakub Kicinski
- Re: [PATCH] phy: nxp-c45: add driver for... Andrew Lunn
- Re: [PATCH] phy: nxp-c45: add driver... Radu Nicolae Pirea (NXP OSS)
- Re: [PATCH] phy: nxp-c45: add dr... Andrew Lunn
- Re: [PATCH] phy: nxp-c45: ad... Radu Nicolae Pirea (NXP OSS)
- Re: [PATCH] phy: nxp-c4... Andrew Lunn
- Re: [PATCH] phy: nx... Radu Nicolae Pirea (NXP OSS)
- Re: [PATCH] phy... Andrew Lunn
- Re: Re: [PATCH]... Christian Herber
- Re: Re: [PATCH]... Andrew Lunn
