On 2/12/21 12:00 PM, Shyam Sundar S K wrote:
Sometimes mailbox commands timeout when the RX data path becomes
unresponsive. This prevents the submission of new mailbox commands to DXIO.
This patch identifies the timeout and resets the RX data path so that the
next message can be submitted properly.
Signed-off-by: Sudheesh Mavila <sudheesh.mav...@amd.com>
Signed-off-by: Shyam Sundar S K <shyam-sundar....@amd.com>
I believe you need a Co-developed-by: before Sudheesh's Signed-off-by:
if he was a co-developer.
---
drivers/net/ethernet/amd/xgbe/xgbe-common.h | 13 +++++++++++
drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c | 25 ++++++++++++++++++++-
2 files changed, 37 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-common.h
b/drivers/net/ethernet/amd/xgbe/xgbe-common.h
index b40d4377cc71..318817450fbd 100644
--- a/drivers/net/ethernet/amd/xgbe/xgbe-common.h
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-common.h
@@ -1279,10 +1279,18 @@
#define MDIO_PMA_10GBR_FECCTRL 0x00ab
#endif
+#ifndef MDIO_PMA_RX_CTRL1
+#define MDIO_PMA_RX_CTRL1 0x8051
+#endif
+
#ifndef MDIO_PCS_DIG_CTRL
#define MDIO_PCS_DIG_CTRL 0x8000
#endif
+#ifndef MDIO_PCS_DIGITAL_STAT
+#define MDIO_PCS_DIGITAL_STAT 0x8010
+#endif
+
#ifndef MDIO_AN_XNP
#define MDIO_AN_XNP 0x0016
#endif
@@ -1358,6 +1366,7 @@
#define XGBE_KR_TRAINING_ENABLE BIT(1)
#define XGBE_PCS_CL37_BP BIT(12)
+#define XGBE_PCS_PSEQ_STATE_BIT 0x10
See comment below, this is a 3-bit field.
#define XGBE_AN_CL37_INT_CMPLT BIT(0)
#define XGBE_AN_CL37_INT_MASK 0x01
@@ -1375,6 +1384,10 @@
#define XGBE_PMA_CDR_TRACK_EN_OFF 0x00
#define XGBE_PMA_CDR_TRACK_EN_ON 0x01
+#define XGBE_PMA_RX_RST_0_MASK BIT(4)
+#define XGBE_PMA_RX_RST_0_RESET_ON 0x10
+#define XGBE_PMA_RX_RST_0_RESET_OFF 0x00
+
/* Bit setting and getting macros
* The get macro will extract the current bit field value from within
* the variable
diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
b/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
index 859ded0c06b0..489f1f86df99 100644
--- a/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
@@ -1953,6 +1953,24 @@ static void xgbe_phy_set_redrv_mode(struct xgbe_prv_data
*pdata)
xgbe_phy_put_comm_ownership(pdata);
}
+static void xgbe_phy_rx_reset(struct xgbe_prv_data *pdata)
+{
+ int reg;
+
+ reg = XMDIO_READ(pdata, MDIO_MMD_PCS, MDIO_PCS_DIGITAL_STAT);
+ if (reg & XGBE_PCS_PSEQ_STATE_BIT) {
The PSEQ_STATE field is a 3 bit field and I believe you're looking for a
POWER_GOOD state, so this should be:
reg = XMDIO_READ_BITS(pdata, MDIO_MMD_PCS, MDIO_PCS_DIGITAL_STAT
XGBE_PCS_PSEQ_STATE_MASK);
if (reg == XGBE_PCS_PSEQ_STATE_POWER_GOOD) {
where the constants define in xgbe-common.h should be:
#define XGBE_PCS_PSEQ_STATE_MASK 0x1c
#define XGBE_PCS_PSEQ_STATE_POWER_GOOD 0x10
+ /* mailbox command timed out, reset Rx block */
+ /* Assert reset bit for 8ns and wait for 40us */
Please combine this comment and be sure to capitalize appropriately.
+ XMDIO_WRITE_BITS(pdata, MDIO_MMD_PMAPMD, MDIO_PMA_RX_CTRL1,
+ XGBE_PMA_RX_RST_0_MASK,
XGBE_PMA_RX_RST_0_RESET_ON);
+ ndelay(20);
This time doesn't match the comment of 8ns... which one is correct?
+ XMDIO_WRITE_BITS(pdata, MDIO_MMD_PMAPMD, MDIO_PMA_RX_CTRL1,
+ XGBE_PMA_RX_RST_0_MASK,
XGBE_PMA_RX_RST_0_RESET_OFF);
+ usleep_range(40, 50);
+ netif_err(pdata, link, pdata->netdev, "firmware mailbox reset
performed\n");
+ }
+}
+
static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
unsigned int cmd, unsigned int sub_cmd)
{
@@ -1960,9 +1978,11 @@ static void xgbe_phy_perform_ratechange(struct
xgbe_prv_data *pdata,
unsigned int wait;
/* Log if a previous command did not complete */
- if (XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS))
+ if (XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS)) {
netif_dbg(pdata, link, pdata->netdev,
"firmware mailbox not ready for command\n");
+ xgbe_phy_rx_reset(pdata);
An extra tab here.
Thanks,
Tom
+ }
/* Construct the command */
XP_SET_BITS(s0, XP_DRIVER_SCRATCH_0, COMMAND, cmd);
@@ -1984,6 +2004,9 @@ static void xgbe_phy_perform_ratechange(struct
xgbe_prv_data *pdata,
netif_dbg(pdata, link, pdata->netdev,
"firmware mailbox command did not complete\n");
+
+ /* Reset on error */
+ xgbe_phy_rx_reset(pdata);
}
static void xgbe_phy_rrc(struct xgbe_prv_data *pdata)
