On 08.10.2020 18:23, Dan Murphy wrote:
> The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
> that supports 10M single pair cable.
>
> The device supports both 2.4-V p2p and 1-V p2p output voltage as defined
> by IEEE 802.3cg 10Base-T1L specfications. These modes can be forced via
> the device tree or the device is defaulted to auto negotiation to
> determine the proper p2p voltage.
>
> Signed-off-by: Dan Murphy <dmur...@ti.com>
> ---
> drivers/net/phy/Kconfig | 6 +
> drivers/net/phy/Makefile | 1 +
> drivers/net/phy/dp83td510.c | 583 ++++++++++++++++++++++++++++++++++++
> 3 files changed, 590 insertions(+)
> create mode 100644 drivers/net/phy/dp83td510.c
>
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index 698bea312adc..017252e1504c 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -302,6 +302,12 @@ config DP83869_PHY
> Currently supports the DP83869 PHY. This PHY supports copper and
> fiber connections.
>
> +config DP83TD510_PHY
> + tristate "Texas Instruments DP83TD510 10M Single Pair Ethernet PHY"
> + help
> + Support for the DP83TD510 Ethernet PHY. This PHY supports a 10M single
> + pair Ethernet connection.
> +
> config VITESSE_PHY
> tristate "Vitesse PHYs"
> help
> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> index a13e402074cf..bf62ce211eb4 100644
> --- a/drivers/net/phy/Makefile
> +++ b/drivers/net/phy/Makefile
> @@ -56,6 +56,7 @@ obj-$(CONFIG_DP83848_PHY) += dp83848.o
> obj-$(CONFIG_DP83867_PHY) += dp83867.o
> obj-$(CONFIG_DP83869_PHY) += dp83869.o
> obj-$(CONFIG_DP83TC811_PHY) += dp83tc811.o
> +obj-$(CONFIG_DP83TD510_PHY) += dp83td510.o
> obj-$(CONFIG_FIXED_PHY) += fixed_phy.o
> obj-$(CONFIG_ICPLUS_PHY) += icplus.o
> obj-$(CONFIG_INTEL_XWAY_PHY) += intel-xway.o
> diff --git a/drivers/net/phy/dp83td510.c b/drivers/net/phy/dp83td510.c
> new file mode 100644
> index 000000000000..0cce9063fd1c
> --- /dev/null
> +++ b/drivers/net/phy/dp83td510.c
> @@ -0,0 +1,583 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Driver for the Texas Instruments DP83TD510 PHY
> + * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +#include <linux/ethtool.h>
> +#include <linux/etherdevice.h>
> +#include <linux/kernel.h>
> +#include <linux/mii.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy.h>
> +#include <linux/netdevice.h>
> +
> +#define DP83TD510E_PHY_ID 0x20000180
> +#define DP83TD510_DEVADDR_AN 0x7
> +#define DP83TD510_DEVADDR 0x1f
> +
> +#define DP83TD510_MII_REG 0x0
> +#define DP83TD510_PHY_STAT 0x10
> +#define DP83TD510_GEN_CFG 0x11
> +#define DP83TD510_INT_REG1 0x12
> +#define DP83TD510_INT_REG2 0x13
> +#define DP83TD510_MAC_CFG_1 0x17
> +
> +#define DP83TD510_SOR_1 0x467
> +
> +#define DP83TD510_HW_RESET BIT(15)
> +#define DP83TD510_SW_RESET BIT(14)
> +
> +/* GEN CFG bits */
> +#define DP83TD510_INT_OE BIT(0)
> +#define DP83TD510_INT_EN BIT(1)
> +
> +/* INT REG 1 bits */
> +#define DP83TD510_INT1_ESD_EN BIT(3)
> +#define DP83TD510_INT1_LINK_EN BIT(5)
> +#define DP83TD510_INT1_RHF_EN BIT(7)
> +#define DP83TD510_INT1_ESD BIT(11)
> +#define DP83TD510_INT1_LINK BIT(13)
> +#define DP83TD510_INT1_RHF BIT(15)
> +
> +/* INT REG 2 bits */
> +#define DP83TD510_INT2_POR_EN BIT(0)
> +#define DP83TD510_INT2_POL_EN BIT(1)
> +#define DP83TD510_INT2_PAGE_EN BIT(5)
> +#define DP83TD510_INT2_POR BIT(8)
> +#define DP83TD510_INT2_POL BIT(9)
> +#define DP83TD510_INT2_PAGE BIT(13)
> +
> +/* MAC CFG bits */
> +#define DP83TD510_RX_CLK_SHIFT BIT(12)
> +#define DP83TD510_TX_CLK_SHIFT BIT(11)
> +
> +#define DP83TD510_MASTER_MODE BIT(2)
> +#define DP83TD510_2_4V BIT(7)
> +#define DP83TD510_RGMII BIT(8)
> +
> +#define DP83TD510_FIFO_DEPTH_MASK GENMASK(6, 5)
> +#define DP83TD510_FIFO_DEPTH_4_B_NIB 0
> +#define DP83TD510_FIFO_DEPTH_5_B_NIB BIT(5)
> +#define DP83TD510_FIFO_DEPTH_6_B_NIB BIT(6)
> +#define DP83TD510_FIFO_DEPTH_8_B_NIB (BIT(5) | BIT(6))
> +
> +enum dp83td510_mode_config {
> + DP83TD510_AUTO_NEG = 0,
> + DP83TD510_MASTER_1 = 1,
> + DP83TD510_MASTER_24 = 2,
> + DP83TD510_SLAVE_1 = 3,
> + DP83TD510_SLAVE_24 = 4,
> +};
> +
> +struct dp83td510_private {
> + u32 forced_mode;
> + u32 tx_fifo_depth;
> + u32 rgmii_delay;
> + bool is_rgmii;
> +};
> +
> +struct dp83td510_init_reg {
> + int reg;
> + int val;
> +};
> +
> +static struct dp83td510_init_reg dp83td510_master_1_0[] = {
> + { 0x000d, 0x0007 }, /* disable auto-neg */
> + { 0x000e, 0x0200 },
> + { 0x000d, 0x4007 },
> + { 0x000e, 0x0000 },
> + { 0x000d, 0x0001 }, /* force master mode */
> + { 0x000e, 0x0834 },
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x4000 },
> + { 0x000d, 0x0001 }, /* force 1.0v swing */
> + { 0x000e, 0x08f6 },
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x0000 },
> + { 0x0608, 0x003b }, /* disable_0_transition */
> + { 0x0862, 0x39f8 }, /* AGC Gain during Autoneg */
> + { 0x081a, 0x67c0 }, /* deq offset for 1V swing */
> + { 0x081c, 0xfb62 }, /* deq offset for 2.4V swing */
> + { 0x0830, 0x05a3 }, /* Enable energy lost fallback */
> + { 0x0855, 0x1b55 }, /* MSE Threshold change */
> + { 0x0831, 0x0403 }, /* energy detect threshold */
> + { 0x0856, 0x1800 }, /* good1 MSE threshold change */
> + { 0x0857, 0x8fa0 }, /* Enable fallback to phase 1 on watchdog trigger */
> + { 0x0871, 0x000c }, /* TED input changed to slicer_in without FFE */
> + { 0x0883, 0x022e }, /* Enable Rx Filter, Change PGA threshold for Short
> Cable detection */
> + { 0x0402, 0x1800 }, /* Adjusr LD swing */
> + { 0x0878, 0x2248 }, /* Change PI up/down polarity */
> + { 0x010c, 0x0008 }, /* tx filter coefficient */
> + { 0x0112, 0x1212 }, /* tx filter scaling factor */
> + { 0x0809, 0x5c80 }, /* AGC retrain */
> + { 0x0803, 0x1529 }, /* Master Ph1 Back-off */
> + { 0x0804, 0x1a33 }, /* Master Ph1 Back-off */
> + { 0x0805, 0x1f3d }, /* Master Ph1 Back-off */
> + { 0x0850, 0x045b }, /* hybrid gain & delay */
> + { 0x0874, 0x6967 }, /* kp step 0 for master */
> + { 0x0852, 0x7800 }, /* FAGC init gain */
> + { 0x0806, 0x1e1e }, /* Master/Slave Ph2 Back-off */
> + { 0x0807, 0x2525 }, /* Master/Slave Ph2 Back-off */
> + { 0x0808, 0x2c2c }, /* Master/Slave Ph2 Back-off */
> + { 0x0850, 0x0590 }, /* Hybrid Gain/Delay Code */
> + { 0x0827, 0x4000 }, /* Echo Fixed Delay */
> + { 0x0849, 0x0fe4 }, /* Hybrid Cal enable */
> + { 0x084b, 0x04b5 }, /* Echo Score Sel */
> + { 0x0018, 0x0043 }, /* Set CRS/RX_DV pin as RX_DV for RMII repeater
> mode */
> +};
> +
> +static struct dp83td510_init_reg dp83td510_slave_1_0[] = {
> + { 0x000d, 0x0007 }, /* disable auto-neg */
> + { 0x000e, 0x0200 },
> + { 0x000d, 0x4007 },
> + { 0x000e, 0x0000 },
> + { 0x000d, 0x0001 }, /* force slave mode */
> + { 0x000e, 0x0834 },
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x0000 },
> + { 0x000d, 0x0001 }, /* force 1.0v swing */
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x0000 },
> + { 0x0608, 0x003b }, /* disable_0_transition */
> + { 0x0862, 0x39f8 }, /* AGC Gain during Autoneg */
> + { 0x081a, 0x67c0 }, /* deq offset for 1V swing */
> + { 0x081c, 0xfb62 }, /* deq offset for 2.4V swing */
> + { 0x0830, 0x05a3 }, /* Enable energy lost fallback */
> + { 0x0855, 0x1b55 }, /* MSE Threshold change */
> + { 0x0831, 0x0403 }, /* energy detect threshold */
> + { 0x0856, 0x1800 }, /* good1 MSE threshold change */
> + { 0x0857, 0x8fa0 }, /* Enable fallback to phase 1 on watchdog trigger */
> + { 0x0871, 0x000c }, /* TED input changed to slicer_in without FFE */
> + { 0x0883, 0x022e }, /* Enable Rx Filter, PGA threshold for Short Cable
> detection */
> + { 0x0402, 0x1800 }, /* Adjusr LD swing */
> + { 0x0878, 0x2248 }, /* Change PI up/down polarity */
> + { 0x010c, 0x0008 }, /* tx filter coefficient */
> + { 0x0112, 0x1212 }, /* tx filter scaling factor */
> + { 0x0809, 0x5c80 }, /* AGC retrain */
> + { 0x0803, 0x1529 }, /* Master Ph1 Back-off */
> + { 0x0804, 0x1a33 }, /* Master Ph1 Back-off */
> + { 0x0805, 0x1f3d }, /* Master Ph1 Back-off */
> + { 0x0850, 0x045b }, /* hybrid gain & delay */
> + { 0x0874, 0x6967 }, /* kp step 0 for master */
> + { 0x0852, 0x7800 }, /* FAGC init gain */
> + { 0x0806, 0x1e1e }, /* Master/Slave Ph2 Back-off */
> + { 0x0807, 0x2525 }, /* Master/Slave Ph2 Back-off */
> + { 0x0808, 0x2c2c }, /* Master/Slave Ph2 Back-off */
> + { 0x0850, 0x0590 }, /* Hybrid Gain/Delay Code */
> + { 0x0827, 0x4000 }, /* Echo Fixed Delay */
> + { 0x0849, 0x0fe4 }, /* Hybrid Cal enable */
> + { 0x084b, 0x04b5 }, /* Echo Score Sel */
> + { 0x0018, 0x0043 }, /* Set CRS/RX_DV pin as RX_DV for RMII repeater
> mode */
> +};
> +
> +static struct dp83td510_init_reg dp83td510_master_2_4[] = {
> + { 0x000d, 0x0007 }, /* disable auto-neg */
> + { 0x000e, 0x0200 },
> + { 0x000d, 0x4007 },
> + { 0x000e, 0x0000 },
> + { 0x000d, 0x0001 }, /* force Master mode */
> + { 0x000e, 0x0834 },
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x4000 },
> + { 0x000d, 0x0001 }, /* force 2.4v swing */
> + { 0x000e, 0x08f6 },
> + { 0x000d, 0x4001 },
> + { 0x000e, 0x1000 },
> + { 0x0608, 0x003b }, /* disable_0_transition */
> + { 0x0862, 0x39f8 }, /* AGC Gain during Autoneg */
> + { 0x081a, 0x67c0 }, /* deq offset for 1V swing */
> + { 0x081c, 0xfb62 }, /* deq offset for 2.4V swing */
> + { 0x0830, 0x05a3 }, /* Enable energy lost fallback */
> + { 0x0855, 0x1b55 }, /* MSE Threshold change */
> + { 0x0831, 0x0403 }, /* energy detect threshold */
> + { 0x0856, 0x1800 }, /* good1 MSE threshold change */
> + { 0x0857, 0x8fa0 }, /* Enable fallback to phase 1 on watchdog trigger */
> + { 0x0871, 0x000c }, /* TED input changed to slicer_in without FFE */
> + { 0x0883, 0x022e }, /* Enable Rx Filter, Change PGA threshold for Short
> Cable detection */
> + { 0x0402, 0x1800 }, /* Adjusr LD swing */
> + { 0x0878, 0x2248 }, /* Change PI up/down polarity */
> + { 0x010c, 0x0008 }, /* tx filter coefficient */
> + { 0x0112, 0x1212 }, /* tx filter scaling factor */
> + { 0x0809, 0x5c80 }, /* AGC retrain */
> + { 0x0803, 0x1529 }, /* Master Ph1 Back-off */
> + { 0x0804, 0x1a33 }, /* Master Ph1 Back-off */
> + { 0x0805, 0x1f3d }, /* Master Ph1 Back-off */
> + { 0x0850, 0x045b }, /* hybrid gain & delay */
> + { 0x0874, 0x6967 }, /* kp step 0 for master */
> + { 0x0852, 0x7800 }, /* FAGC init gain */
> + { 0x0806, 0x1e1e }, /* Master/Slave Ph2 Back-off */
> + { 0x0807, 0x2525 }, /* Master/Slave Ph2 Back-off */
> + { 0x0808, 0x2c2c }, /* Master/Slave Ph2 Back-off */
> + { 0x0850, 0x0590 }, /* Hybrid Gain/Delay Code */
> + { 0x0827, 0x4000 }, /* Echo Fixed Delay */
> + { 0x0849, 0x0fe4 }, /* Hybrid Cal enable */
> + { 0x084b, 0x04b5 }, /* Echo Score Sel */
> + { 0x0018, 0x0043 }, /* Set CRS/RX_DV pin as RX_DV for RMII repeater
> mode */
> +};
> +
> +static struct dp83td510_init_reg dp83td510_slave_2_4[] = {
> + { 0x000d, 0x0007}, /* disable auto-neg */
> + { 0x000e, 0x0200},
> + { 0x000d, 0x4007},
> + { 0x000e, 0x0000},
> + { 0x000d, 0x0001}, /* force slave mode */
> + { 0x000e, 0x0834},
> + { 0x000d, 0x4001},
> + { 0x000e, 0x0000},
> + { 0x000d, 0x0001}, /* force 2.4v swing */
> + { 0x000e, 0x08f6},
> + { 0x000d, 0x4001},
> + { 0x000e, 0x1000},
> + { 0x0608, 0x003b}, /* disable_0_transition */
> + { 0x0862, 0x39f8}, /* AGC Gain during Autoneg */
> + { 0x081a, 0x67c0}, /* deq offset for 1V swing */
> + { 0x081c, 0xfb62}, /* deq offset for 2.4V swing */
> + { 0x0830, 0x05a3}, /* Enable energy lost fallback */
> + { 0x0855, 0x1b55}, /* MSE Threshold change */
> + { 0x0831, 0x0403}, /* energy detect threshold */
> + { 0x0856, 0x1800}, /* good1 MSE threshold change */
> + { 0x0857, 0x8fa0}, /* Enable fallback to phase 1 on watchdog trigger */
> + { 0x0871, 0x000c}, /* TED input changed to slicer_in without FFE */
> + { 0x0883, 0x022e}, /* Enable Rx Filter, Change PGA threshold for Short
> Cable detection */
> + { 0x0402, 0x1800}, /* Adjusr LD swing */
> + { 0x0878, 0x2248}, /* Change PI up/down polarity */
> + { 0x010c, 0x0008}, /* tx filter coefficient */
> + { 0x0112, 0x1212}, /* tx filter scaling factor */
> + { 0x0809, 0x5c80}, /* AGC retrain */
> + { 0x0803, 0x1529}, /* Master Ph1 Back-off */
> + { 0x0804, 0x1a33}, /* Master Ph1 Back-off */
> + { 0x0805, 0x1f3d}, /* Master Ph1 Back-off */
> + { 0x0850, 0x045b}, /* hybrid gain & delay */
> + { 0x0874, 0x6967}, /* kp step 0 for master */
> + { 0x0852, 0x7800}, /* FAGC init gain */
> + { 0x0806, 0x1e1e}, /* Master/Slave Ph2 Back-off */
> + { 0x0807, 0x2525}, /* Master/Slave Ph2 Back-off */
> + { 0x0808, 0x2c2c}, /* Master/Slave Ph2 Back-off */
> + { 0x0850, 0x0590}, /* Hybrid Gain/Delay Code */
> + { 0x0827, 0x4000}, /* Echo Fixed Delay */
> + { 0x0849, 0x0fe4}, /* Hybrid Cal enable */
> + { 0x084b, 0x04b5}, /* Echo Score Sel */
> + { 0x0018, 0x0043}, /* Set CRS/RX_DV pin as RX_DV for RMII repeater mode
> */
> +};
> +
> +static struct dp83td510_init_reg dp83td510_auto_neg[] = {
> + { 0x608, 0x003b }, /* disable_0_transition */
> + { 0x862, 0x39f8 }, /* AGC Gain during Autoneg */
> + { 0x81a, 0x67c0 }, /* deq offset for 1V swing */
> + { 0x81c, 0xfb62 }, /* deq offset for 2.4V swing */
> + { 0x830, 0x05a3 }, /* Enable energy lost fallback */
> + { 0x855, 0x1b55 }, /* MSE Threshold change */
> + { 0x831, 0x0403 }, /* energy detect threshold */
> + { 0x856, 0x1800 }, /* good1 MSE threshold change */
> + { 0x857, 0x8fa0 }, /* Enable fallback to phase 1 on watchdog trigger */
> + { 0x871, 0x000c }, /* TED input changed to slicer_in without FFE */
> + { 0x883, 0x022e }, /* Enable Rx Filter Change PGA threshold for Short
> Cable detection */
> + { 0x402, 0x1800 }, /* Adjusr LD swing */
> + { 0x878, 0x2248 }, /* Change PI up/down polarity */
> + { 0x10c, 0x0008 }, /* tx filter coefficient */
> + { 0x112, 0x1212 }, /* tx filter scaling factor */
> + { 0x809, 0x5c80 }, /* AGC retrain */
> + { 0x803, 0x1529 }, /* Master Ph1 Back-off */
> + { 0x804, 0x1a33 }, /* Master Ph1 Back-off */
> + { 0x805, 0x1f3d }, /* Master Ph1 Back-off */
> + { 0x850, 0x045b }, /* hybrid gain & delay */
> + { 0x874, 0x6967 }, /* kp step 0 for master */
> + { 0x852, 0x7800 }, /* FAGC init gain */
> + { 0x806, 0x1e1e }, /* Master/Slave Ph2 Back-off */
> + { 0x807, 0x2525 }, /* Master/Slave Ph2 Back-off */
> + { 0x808, 0x2c2c }, /* Master/Slave Ph2 Back-off */
> + { 0x850, 0x0590 }, /* Hybrid Gain/Delay Code */
> + { 0x827, 0x4000 }, /* Echo Fixed Delay */
> + { 0x849, 0x0fe4 }, /* Hybrid Cal enable */
> + { 0x84b, 0x04b5 }, /* Echo Score Sel */
> + { 0x018, 0x0043 }, /* Set CRS/RX_DV pin as RX_DV for RMII repeater mode
> */
> +};
> +
> +static int dp83td510_ack_interrupt(struct phy_device *phydev)
> +{
> + int ret;
> +
> + ret = phy_read(phydev, DP83TD510_INT_REG1);
> + if (ret < 0)
> + return ret;
> +
> + ret = phy_read(phydev, DP83TD510_INT_REG2);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int dp83td510_config_intr(struct phy_device *phydev)
> +{
> + int int_status;
> + int gen_cfg_val;
> + int ret;
> +
> + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
> + int_status = phy_read(phydev, DP83TD510_INT_REG1);
> + if (int_status < 0)
> + return int_status;
> +
> + int_status = (DP83TD510_INT1_ESD_EN | DP83TD510_INT1_LINK_EN |
> + DP83TD510_INT1_RHF_EN);
> +
> + ret = phy_write(phydev, DP83TD510_INT_REG1, int_status);
> + if (ret)
> + return ret;
> +
> + int_status = phy_read(phydev, DP83TD510_INT_REG2);
> + if (int_status < 0)
> + return int_status;
> +
> + int_status = (DP83TD510_INT2_POR | DP83TD510_INT2_POL |
> + DP83TD510_INT2_PAGE);
> +
> + ret = phy_write(phydev, DP83TD510_INT_REG2, int_status);
> + if (ret)
> + return ret;
> +
> + gen_cfg_val = phy_read(phydev, DP83TD510_GEN_CFG);
> + if (gen_cfg_val < 0)
> + return gen_cfg_val;
> +
> + gen_cfg_val |= DP83TD510_INT_OE | DP83TD510_INT_EN;
> +
> + } else {
> + ret = phy_write(phydev, DP83TD510_INT_REG1, 0);
> + if (ret)
> + return ret;
> +
> + ret = phy_write(phydev, DP83TD510_INT_REG2, 0);
> + if (ret)
> + return ret;
> +
> + gen_cfg_val = phy_read(phydev, DP83TD510_GEN_CFG);
> + if (gen_cfg_val < 0)
> + return gen_cfg_val;
> +
> + gen_cfg_val &= ~DP83TD510_INT_EN;
> + }
> +
> + return phy_write(phydev, DP83TD510_GEN_CFG, gen_cfg_val);
> +}
> +
> +static int dp83td510_configure_mode(struct phy_device *phydev)
> +{
> + struct dp83td510_private *dp83td510 = phydev->priv;
> + struct dp83td510_init_reg *init_data;
> + int size;
> + int ret;
> + int i;
> +
> + ret = phy_set_bits(phydev, DP83TD510_MII_REG, DP83TD510_HW_RESET);
> + if (ret < 0)
> + return ret;
> +
> + switch (dp83td510->forced_mode) {
> + case DP83TD510_MASTER_1:
> + size = ARRAY_SIZE(dp83td510_master_1_0);
> + init_data = dp83td510_master_1_0;
> + break;
> + case DP83TD510_MASTER_24:
> + size = ARRAY_SIZE(dp83td510_master_2_4);
> + init_data = dp83td510_master_2_4;
> + break;
> + case DP83TD510_SLAVE_1:
> + size = ARRAY_SIZE(dp83td510_slave_1_0);
> + init_data = dp83td510_slave_1_0;
> + break;
> + case DP83TD510_SLAVE_24:
> + size = ARRAY_SIZE(dp83td510_slave_2_4);
> + init_data = dp83td510_slave_2_4;
> + break;
> + case DP83TD510_AUTO_NEG:
> + default:
> + size = ARRAY_SIZE(dp83td510_auto_neg);
> + init_data = dp83td510_auto_neg;
> + break;
> + };
> +
> + for (i = 0; i < size; i++) {
> + ret = phy_write_mmd(phydev, DP83TD510_DEVADDR, init_data[i].reg,
> + init_data[i].val);
> + if (ret)
> + return ret;
> + }
> +
> + return phy_set_bits(phydev, DP83TD510_MII_REG, DP83TD510_SW_RESET);
> +}
> +
> +static int dp83td510_config_init(struct phy_device *phydev)
> +{
> + struct dp83td510_private *dp83td510 = phydev->priv;
> + int ret = 0;
> +
> + if (phy_interface_is_rgmii(phydev)) {
> + if (dp83td510->rgmii_delay) {
> + ret = phy_set_bits_mmd(phydev, DP83TD510_DEVADDR,
> + DP83TD510_MAC_CFG_1,
> dp83td510->rgmii_delay);
> + if (ret)
> + return ret;
> + }
> + }
> +
> + if (phydev->interface == PHY_INTERFACE_MODE_RMII)
> + ret = phy_modify(phydev, DP83TD510_GEN_CFG,
> + DP83TD510_FIFO_DEPTH_MASK,
> + dp83td510->tx_fifo_depth);
> +
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT,
> phydev->advertising);
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT,
> phydev->supported);
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
> phydev->advertising);
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
> phydev->supported);
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_MII_BIT, phydev->advertising);
> + linkmode_clear_bit(ETHTOOL_LINK_MODE_MII_BIT, phydev->supported);
> +
> + return dp83td510_configure_mode(phydev);
> +}
> +
> +static int dp83td510_phy_reset(struct phy_device *phydev)
> +{
> + int ret;
> +
> + ret = phy_set_bits(phydev, DP83TD510_MII_REG, DP83TD510_SW_RESET);
> + if (ret < 0)
> + return ret;
> +
> + usleep_range(10, 20);
> +
> + return dp83td510_config_init(phydev);
> +}
> +
> +static int dp83td510_read_straps(struct phy_device *phydev)
> +{
> + struct dp83td510_private *dp83td510 = phydev->priv;
> + int strap;
> +
> + strap = phy_read_mmd(phydev, DP83TD510_DEVADDR, DP83TD510_SOR_1);
> + if (strap < 0)
> + return strap;
> +
> + if (strap & DP83TD510_RGMII)
> + dp83td510->is_rgmii = true;
> +
> + return 0;
> +};
> +
> +#if IS_ENABLED(CONFIG_OF_MDIO)
> +static int dp83td510_of_init(struct phy_device *phydev)
> +{
> + struct dp83td510_private *dp83td510 = phydev->priv;
> + struct device *dev = &phydev->mdio.dev;
> + struct device_node *of_node = dev->of_node;
> + s32 rx_int_delay;
> + s32 tx_int_delay;
> + int ret;
> +
> + if (!of_node)
> + return -ENODEV;
> +
> + ret = dp83td510_read_straps(phydev);
> + if (ret)
> + return ret;
> +
> + ret = device_property_read_u32(&phydev->mdio.dev,
> "ti,master-slave-mode",
> + &dp83td510->forced_mode);
> + if (ret)
> + dp83td510->forced_mode = DP83TD510_AUTO_NEG;
> +
> + if (dp83td510->forced_mode < DP83TD510_AUTO_NEG ||
> + dp83td510->forced_mode > DP83TD510_SLAVE_24)
> + return -EINVAL;
> +
> + if (device_property_read_u32(&phydev->mdio.dev, "tx-fifo-depth",
> + &dp83td510->tx_fifo_depth))
> + dp83td510->tx_fifo_depth = DP83TD510_FIFO_DEPTH_5_B_NIB;
> +
> + switch (dp83td510->tx_fifo_depth) {
> + case 4:
> + dp83td510->tx_fifo_depth = DP83TD510_FIFO_DEPTH_4_B_NIB;
> + break;
> + case 5:
> + dp83td510->tx_fifo_depth = DP83TD510_FIFO_DEPTH_5_B_NIB;
> + break;
> + case 6:
> + dp83td510->tx_fifo_depth = DP83TD510_FIFO_DEPTH_6_B_NIB;
> + break;
> + case 8:
> + dp83td510->tx_fifo_depth = DP83TD510_FIFO_DEPTH_8_B_NIB;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + rx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0, true);
> + if (rx_int_delay <= 0)
> + dp83td510->rgmii_delay = DP83TD510_RX_CLK_SHIFT;
> + else
> + dp83td510->rgmii_delay = 0;
> +
> + tx_int_delay = phy_get_internal_delay(phydev, dev, NULL, 0, false);
> + if (tx_int_delay <= 0)
> + dp83td510->rgmii_delay |= DP83TD510_TX_CLK_SHIFT;
> + else
> + dp83td510->rgmii_delay &= ~DP83TD510_TX_CLK_SHIFT;
> +
> + return ret;
> +}
> +#else
> +static int dp83869_of_init(struct phy_device *phydev)
> +{
> + return dp83td510_read_straps(phydev);
> +}
> +#endif /* CONFIG_OF_MDIO */
> +
> +static int dp83td510_probe(struct phy_device *phydev)
> +{
> + struct dp83td510_private *dp83td510;
> + int ret;
> +
> + dp83td510 = devm_kzalloc(&phydev->mdio.dev, sizeof(*dp83td510),
> GFP_KERNEL);
> + if (!dp83td510)
> + return -ENOMEM;
> +
> + phydev->priv = dp83td510;
> +
> + ret = dp83td510_of_init(phydev);
> + if (ret)
> + return ret;
> +
> + return dp83td510_config_init(phydev);
> +}
> +
> +static struct phy_driver dp83td510_driver[] = {
> + {
> + PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID),
> + .name = "TI DP83TD510E",
> + .probe = dp83td510_probe,
> + .config_init = dp83td510_config_init,
> + .soft_reset = dp83td510_phy_reset,
> + .features = PHY_BASIC_FEATURES,
Per default phylib uses genphy_read_abilities() to auto-detect
the features. Doesn't your PHY support the needed clause 22
standard registers? Or are they incorrectly populated?
Maybe better than setting PHY_BASIC_FEATURES and then removing
unsuported features in dp83td510_config_init() would be to
implement phy_driver callback get_features. Then you can set
the supported fatures directly.
> +
> + /* IRQ related */
> + .ack_interrupt = dp83td510_ack_interrupt,
> + .config_intr = dp83td510_config_intr,
> +
> + .suspend = genphy_suspend,
> + .resume = genphy_resume,
> + },
> +};
> +module_phy_driver(dp83td510_driver);
> +
> +static struct mdio_device_id __maybe_unused dp83td510_tbl[] = {
> + { PHY_ID_MATCH_MODEL(DP83TD510E_PHY_ID) },
> + { }
> +};
> +MODULE_DEVICE_TABLE(mdio, dp83td510_tbl);
> +
> +MODULE_DESCRIPTION("Texas Instruments DP83TD510E PHY driver");
> +MODULE_AUTHOR("Dan Murphy <dmur...@ti.com");
> +MODULE_LICENSE("GPL v2");
> +
>
