Add CPSW Port's Interface Mode Selection PHY (phy-gmii-sel) DT Bindings
Cc: Kishon Vijay Abraham I <kis...@ti.com>
Cc: Tony Lindgren <t...@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.stras...@ti.com>
---
.../devicetree/bindings/phy/ti-phy-gmii-sel.txt | 68 ++++++++++++++++++++++
1 file changed, 68 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt
diff --git a/Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt
b/Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt
new file mode 100644
index 0000000..50ce9ae
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt
@@ -0,0 +1,68 @@
+CPSW Port's Interface Mode Selection PHY Tree Bindings
+-----------------------------------------------
+
+TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports
+two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII
interfaces.
+The interface mode is selected by configuring the MII mode selection
register(s)
+(GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and
+bit fields placement in SCM are different between SoCs while fields meaning
+is the same.
+ +--------------+
+ +-------------------------------+ |SCM |
+ | CPSW | | +---------+ |
+ | +--------------------------------+gmii_sel | |
+ | | | | +---------+ |
+ | +----v---+ +--------+ | +--------------+
+ | |Port 1..<--+-->GMII/MII<------->
+ | | | | | | |
+ | +--------+ | +--------+ |
+ | | |
+ | | +--------+ |
+ | | | RMII <------->
+ | +--> | |
+ | | +--------+ |
+ | | |
+ | | +--------+ |
+ | | | RGMII <------->
+ | +--> | |
+ | +--------+ |
+ +-------------------------------+
+
+CPSW Port's Interface Mode Selection PHY describes MII interface mode between
+CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration.
+
+CPSW Port's Interface Mode Selection PHY device should defined as child device
+of SCM node (scm_conf) and can be attached to each CPSW port node using
standard
+PHY bindings (See phy/phy-bindings.txt).
+
+Required properties:
+- compatible : Should be "ti,am3352-phy-gmii-sel" for am335x platform
+ "ti,dra7xx-phy-gmii-sel" for dra7xx/am57xx platform
+ "ti,am43xx-phy-gmii-sel" for am43xx platform
+ "ti,dm814-phy-gmii-sel" for dm814x platform
+- reg : Address and length of the register set for the device
+- #phy-cells : must be 2.
+ cell 1 - CPSW port number (starting from 1)
+ cell 2 - RMII refclk mode
+
+Examples:
+ phy_gmii_sel: phy-gmii-sel {
+ compatible = "ti,am3352-phy-gmii-sel";
+ reg = <0x650 0x4>;
+ #phy-cells = <2>;
+ };
+
+ mac: ethernet@4a100000 {
+ compatible = "ti,am335x-cpsw","ti,cpsw";
+ ...
+
+ cpsw_emac0: slave@4a100200 {
+ ...
+ phys = <&phy_gmii_sel 1 1>;
+ };
+
+ cpsw_emac1: slave@4a100300 {
+ ...
+ phys = <&phy_gmii_sel 2 1>;
+ };
+ };
--
2.10.5
