On 3/27/2018 10:47 PM, Florian Fainelli wrote:
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e875421e ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: Florian Fainelli <f.faine...@gmail.com>
---
drivers/net/ethernet/broadcom/bcmsysport.c | 57 ++++++++++++++++++++----------
drivers/net/ethernet/broadcom/bcmsysport.h | 4 +--
2 files changed, 41 insertions(+), 20 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bcmsysport.c
b/drivers/net/ethernet/broadcom/bcmsysport.c
index 1e52bb7d822e..43ad6300c351 100644
--- a/drivers/net/ethernet/broadcom/bcmsysport.c
+++ b/drivers/net/ethernet/broadcom/bcmsysport.c
@@ -574,16 +574,16 @@ static int bcm_sysport_set_wol(struct net_device *dev,
return 0;
}
-static void bcm_sysport_set_rx_coalesce(struct bcm_sysport_priv *priv)
+static void bcm_sysport_set_rx_coalesce(struct bcm_sysport_priv *priv,
+ u32 usecs, u32 pkts)
{
u32 reg;
reg = rdma_readl(priv, RDMA_MBDONE_INTR);
reg &= ~(RDMA_INTR_THRESH_MASK |
RDMA_TIMEOUT_MASK << RDMA_TIMEOUT_SHIFT);
- reg |= priv->dim.coal_pkts;
- reg |= DIV_ROUND_UP(priv->dim.coal_usecs * 1000, 8192) <<
- RDMA_TIMEOUT_SHIFT;
+ reg |= pkts;
+ reg |= DIV_ROUND_UP(usecs * 1000, 8192) << RDMA_TIMEOUT_SHIFT;
rdma_writel(priv, reg, RDMA_MBDONE_INTR);
}
@@ -626,6 +626,8 @@ static int bcm_sysport_set_coalesce(struct net_device *dev,
struct ethtool_coalesce *ec)
{
struct bcm_sysport_priv *priv = netdev_priv(dev);
+ struct net_dim_cq_moder moder;
+ u32 usecs, pkts;
unsigned int i;
/* Base system clock is 125Mhz, DMA timeout is this reference clock
@@ -646,15 +648,22 @@ static int bcm_sysport_set_coalesce(struct net_device
*dev,
for (i = 0; i < dev->num_tx_queues; i++)
bcm_sysport_set_tx_coalesce(&priv->tx_rings[i], ec);
- priv->dim.coal_usecs = ec->rx_coalesce_usecs;
- priv->dim.coal_pkts = ec->rx_max_coalesced_frames;
+ priv->rx_coalesce_usecs = ec->rx_coalesce_usecs;
+ priv->rx_max_coalesced_frames = ec->rx_max_coalesced_frames;
+ usecs = priv->rx_coalesce_usecs;
+ pkts = priv->rx_max_coalesced_frames;
- if (!ec->use_adaptive_rx_coalesce && priv->dim.use_dim) {
- priv->dim.coal_pkts = 1;
- priv->dim.coal_usecs = 0;
+ /* If DIM is enabled, immediately obtain default parameters */
+ if (ec->use_adaptive_rx_coalesce) {
+ moder = net_dim_get_def_profile(priv->dim.dim.mode);
+ usecs = moder.usec;
+ pkts = moder.pkts;
}
What if DIM is already in use? We don't want to set default values if
DIM is already working.
+
priv->dim.use_dim = ec->use_adaptive_rx_coalesce;
- bcm_sysport_set_rx_coalesce(priv);
+
+ /* Apply desired coalescing parameters */
+ bcm_sysport_set_rx_coalesce(priv, usecs, pkts);
return 0;
}
@@ -1058,10 +1067,7 @@ static void bcm_sysport_dim_work(struct work_struct
*work)
struct net_dim_cq_moder cur_profile =
net_dim_get_profile(dim->mode, dim->profile_ix);
- priv->dim.coal_usecs = cur_profile.usec;
- priv->dim.coal_pkts = cur_profile.pkts;
-
- bcm_sysport_set_rx_coalesce(priv);
+ bcm_sysport_set_rx_coalesce(priv, cur_profile.usec, cur_profile.pkts);
dim->state = NET_DIM_START_MEASURE;
}
@@ -1408,14 +1414,30 @@ static void bcm_sysport_adj_link(struct net_device *dev)
phy_print_status(phydev);
}
-static void bcm_sysport_init_dim(struct bcm_sysport_net_dim *dim,
+static void bcm_sysport_init_dim(struct bcm_sysport_priv *priv,
void (*cb)(struct work_struct *work))
{
+ struct bcm_sysport_net_dim *dim = &priv->dim;
+ struct net_dim_cq_moder moder;
+ u32 usecs, pkts;
+
INIT_WORK(&dim->dim.work, cb);
dim->dim.mode = NET_DIM_CQ_PERIOD_MODE_START_FROM_EQE;
dim->event_ctr = 0;
dim->packets = 0;
dim->bytes = 0;
I would expect only dim related code in a function called init_dim(). I
think the code below should be elsewhere. Or maybe change the function
name to init_rx_coalesce().
+
+ usecs = priv->rx_coalesce_usecs;
+ pkts = priv->rx_max_coalesced_frames;
+
+ /* If DIM was enabled, re-apply default parameters */
+ if (dim->use_dim) {
+ moder = net_dim_get_def_profile(dim->dim.mode);
+ usecs = moder.usec;
+ pkts = moder.pkts;
+ }
+
+ bcm_sysport_set_rx_coalesce(priv, usecs, pkts);
}
static int bcm_sysport_init_tx_ring(struct bcm_sysport_priv *priv,
@@ -1658,8 +1680,6 @@ static int bcm_sysport_init_rx_ring(struct
bcm_sysport_priv *priv)
rdma_writel(priv, 0, RDMA_END_ADDR_HI);
rdma_writel(priv, priv->num_rx_desc_words - 1, RDMA_END_ADDR_LO);
- rdma_writel(priv, 1, RDMA_MBDONE_INTR);
-
netif_dbg(priv, hw, priv->netdev,
"RDMA cfg, num_rx_bds=%d, rx_bds=%p\n",
priv->num_rx_bds, priv->rx_bds);
@@ -1827,7 +1847,7 @@ static void bcm_sysport_netif_start(struct net_device
*dev)
struct bcm_sysport_priv *priv = netdev_priv(dev);
/* Enable NAPI */
- bcm_sysport_init_dim(&priv->dim, bcm_sysport_dim_work);
+ bcm_sysport_init_dim(priv, bcm_sysport_dim_work);
napi_enable(&priv->napi);
/* Enable RX interrupt and TX ring full interrupt */
@@ -2333,6 +2353,7 @@ static int bcm_sysport_probe(struct platform_device *pdev)
/* libphy will adjust the link state accordingly */
netif_carrier_off(dev);
+ priv->rx_max_coalesced_frames = 1;
u64_stats_init(&priv->syncp);
priv->dsa_notifier.notifier_call = bcm_sysport_dsa_notifier;
diff --git a/drivers/net/ethernet/broadcom/bcmsysport.h
b/drivers/net/ethernet/broadcom/bcmsysport.h
index 57e18ef8f206..d6e5d0cbf3a3 100644
--- a/drivers/net/ethernet/broadcom/bcmsysport.h
+++ b/drivers/net/ethernet/broadcom/bcmsysport.h
@@ -701,8 +701,6 @@ struct bcm_sysport_net_dim {
u16 event_ctr;
unsigned long packets;
unsigned long bytes;
- u32 coal_usecs;
- u32 coal_pkts;
struct net_dim dim;
};
@@ -755,6 +753,8 @@ struct bcm_sysport_priv {
unsigned int rx_c_index;
struct bcm_sysport_net_dim dim;
+ u32 rx_max_coalesced_frames;
+ u32 rx_coalesce_usecs;
/* PHY device */
struct device_node *phy_dn;
