Sorry for the delay in response there, however, I've got a little more info.
-I upgraded the router (computer B) to 2.6.13, and there's no noticeable
change in performance.
-If 2.6.12 is fine, I've replicated the bug (using FTP).
-System hard locks ONLY when RECIEVING, NOT sending.
-I tested (and confirmed this) against a 100mbps xbox. I can copy
from it at a full 100mbps (borderline 10MB/sec), but sending to it
causes a lock.
-As torrenting with heavy downstream (~500kB/sec) causes a lock in
roughly 20 minutes of use (tops), and 20 seconds of FTP with 10MB/sec
causes a lock in a matter of seconds, I'd imagine that using a gigabit
end connection would lock it rather quickly.
One thing of note... I have an NV FX5200 in here, likewise using the
nvidia "kernel tainting" drivers. Do I 100% NEED TO replicate this with
that module unloaded, or is it fine (if nothing else, for now)?
The other thing... as I said, I bought three. Two of them run linux, my
desktop and my router. My router does not seem to lock, my desktop does.
The main difference? The desktop has a 64-bit PCI card slot, and
likewise is in use. Other than that, I can't name a (real) difference...
Attached is the requested info. If the mailing list strips them all,
I'll repaste inline.
If this "passes" you guys, I'll file it on the bug tracker.
Thanks,
Kyle
Francois Romieu wrote:
>Kyle Brantley <[EMAIL PROTECTED]> :
>[...]
>
>
>>I recently bought three rtl8169 gigabit cards, along with a gigabit
>>switch. Trouble is, the computers keep freezing up once the NIC comes
>>under and "decent" amount of load. Let me lay this out for you a bit:
>>
>>Computer A:
>>-Dual AMD 2600+ MP
>>-rtl8169 under *64-bit PCI slot*
>>-2.6.12 (vanilla)
>>
>>
>
>It should be fine.
>
>
>
>>Computer B:
>>-Intel P4 2.4GHz
>>-rtl8169 under 32-bit PCI slot
>>-2.6.10 (vanilla)
>>
>>
>
>Please upgrade this one.
>
>[...]
>
>
>>I've googled around (quite a bit), and found many many different patches
>>for the 8169 driver.
>>
>>
>
>The patches are regularly pushed in mainline. Don't panic.
>
>[...]
>
>
>>Any help would be appreciated.
>>
>>
>
>Upgrading the kernel in the 2.6.10 box should fix a known issue.
>
>Be sure to enable the magic sysrq in your new compilation.
>
>If it is not enough, you may have found something new:
>- please open a PR at http://bugzilla.kernel.org
>- send:
> o 'lspci -vx'
> o complete dmesg after log (check that the very first lines do not
> disappear),
> o lsmod
> o cat /proc/interrupts before f*ckup
> o ifconfig output
>- do the keyboard led still answer after the lockup ?
>- is NFS implied in your configuration ?
> If not can you reproduce the issue with torrent or ftp alone ?
>
>--
>Ueimor
>
>
>
00000000bff80000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000f7170
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0xbfefcf28
ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0xbfefef2e
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0xbfefefa2
ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
Processor #1 6:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000)
Built 1 zonelists
Kernel command line: root=/dev/sda3
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2133.814 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 902432k/917504k available (4243k kernel code, 14548k reserved, 1598k
data, 268k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4194.30 BogoMIPS (lpj=2097152)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: AMD Athlon(tm) MP 2600+ stepping 01
Booting processor 1/0 eip 3000
Initializing CPU#1
Calibrating delay loop... 4243.45 BogoMIPS (lpj=2121728)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) Processor stepping 01
Total of 2 processors activated (8437.76 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 3
groups: 1 2
CPU1 attaching sched-domain:
domain 0: span 3
groups: 2 1
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1126114353.325:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Coda Kernel/Venus communications, v6.0.0, [EMAIL PROTECTED]
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
NTFS driver 2.1.22 [Flags: R/O].
Initializing Cryptographic API
BIOS failed to enable PCI standards compliance, fixing this error.
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AMD 760MP chipset
agpgart: AGP aperture is 64M @ 0xec000000
[drm] Initialized drm 1.0.0 20040925
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 2 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:08.0: 3Com PCI 3c905C Tornado at 0x2480. Vers LK1.1.19
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16
eth1: RealTek RTL8139 at 0x2000, 00:50:22:40:03:00, IRQ 16
eth1: Identified 8139 chip type 'RTL-8139C'
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 20 (level, low) -> IRQ 20
eth2: Identified chip type is 'RTL8169s/8110s'.
eth2: RTL8169 at 0xf884c000, 00:0e:2e:60:70:e5, IRQ 20
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD7441: IDE controller at PCI slot 0000:00:07.1
AMD7441: chipset revision 4
AMD7441: not 100% native mode: will probe irqs later
AMD7441: 0000:00:07.1 (rev 04) UDMA100 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y120L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Maxtor 6Y120L0, ATA DISK drive
hdd: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdc: max request size: 128KiB
hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.11 loaded.
sata_promise version 1.01
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 17 (level, low) -> IRQ 17
ata1: SATA max UDMA/133 cmd 0xF884E200 ctl 0xF884E238 bmdma 0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xF884E280 ctl 0xF884E2B8 bmdma 0x0 irq 17
ata3: SATA max UDMA/133 cmd 0xF884E300 ctl 0xF884E338 bmdma 0x0 irq 17
ata4: SATA max UDMA/133 cmd 0xF884E380 ctl 0xF884E3B8 bmdma 0x0 irq 17
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 72303840 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_promise
ata2: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 72303840 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_promise
ata3: no device found (phy stat 00000000)
scsi2 : sata_promise
ata4: no device found (phy stat 00000000)
scsi3 : sata_promise
Vendor: ATA Model: WDC WD360GD-00FN Rev: 35.0
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD360GD-00FN Rev: 35.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
NFTL driver: nftlcore.c $Revision: 1.97 $, nftlmount.c $Revision: 1.40 $
INFTL: inftlcore.c $Revision: 1.18 $, inftlmount.c $Revision: 1.16 $
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:02:00.0[D] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:02:00.0: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:02:00.0: irq 19, io mem 0xea120000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.2
usb 1-3: new full speed USB device using ohci_hcd and address 2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x07cc, Product: 0x0301, Revision: 0x0005
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 1
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: *** thread sleeping.
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usbcore: registered new driver usbnet
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
mice: PS/2 mouse device common for all mice
I2O subsystem v$Rev$
i2o: max drivers = 8
I2O Block Device OSM v$Rev$
I2O SCSI Peripheral OSM v$Rev$
I2O ProcFS OSM v$Rev$
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 5856.000 MB/sec
raid5: using function: pIII_sse (5856.000 MB/sec)
raid6: int32x1 882 MB/s
raid6: int32x2 1089 MB/s
raid6: int32x4 699 MB/s
raid6: int32x8 687 MB/s
raid6: mmxx1 1824 MB/s
raid6: mmxx2 3273 MB/s
raid6: sse1x1 468 MB/s
raid6: sse1x2 933 MB/s
raid6: using algorithm sse1x2 (933 MB/s)
md: raid6 personality registered as nr 8
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.2
wbsd: Copyright(c) Pierre Ossman
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 220 bytes per conntrack
input: AT Translated Set 2 keyboard on isa0060/serio0
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <[EMAIL PROTECTED]>.
http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
ACPI wakeup devices:
PCI0 OP2P USB0
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering hdc2 ...
md: adding hdc2 ...
md: hdc1 has different UUID to hdc2
md: adding hda2 ...
md: hda1 has different UUID to hdc2
md: created md1
md: bind<hda2>
md: bind<hdc2>
md: running: <hdc2><hda2>
md1: setting max_sectors to 128, segment boundary to 32767
raid0: looking at hdc2
raid0: comparing hdc2(120011968) with hdc2(120011968)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at hda2
raid0: comparing hda2(120011392) with hdc2(120011968)
raid0: NOT EQUAL
raid0: comparing hda2(120011392) with hda2(120011392)
raid0: END
raid0: ==> UNIQUE
raid0: 2 zones
raid0: FINAL 2 zones
raid0: zone 1
raid0: checking hdc2 ... contained as device 0
(120011968) is smallest!.
raid0: checking hda2 ... nope.
raid0: zone->nb_dev: 1, size: 576
raid0: current zone offset: 120011968
raid0: done.
raid0 : md_size is 240023360 blocks.
raid0 : conf->hash_spacing is 240022784 blocks.
raid0 : nb_zone is 2.
raid0 : Allocating 8 bytes for hash.
md: considering hdc1 ...
md: adding hdc1 ...
md: adding hda1 ...
md: created md0
md: bind<hda1>
md: bind<hdc1>
md: running: <hdc1><hda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: replayed 1 transactions in 0 seconds
ReiserFS: sda3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 268k freed
ReiserFS: sda3: Removing [5455 11536 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11510 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11495 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11463 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11447 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11430 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11413 0x0 SD]..done
ReiserFS: sda3: Removing [5455 11409 0x0 SD]..done
ReiserFS: sda3: There were 8 uncompleted unlinks/truncates. Completed
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: USB2.0 Model: CardReader CF RW Rev: 0814
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000002 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000002 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000003 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000003 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000004 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000004 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
Attached scsi removable disk sdc at scsi4, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi4, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 20 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 36 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: USB2.0 Model: CardReader Combo Rev: 0814
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000006 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000006 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000007 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000007 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 20 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x8 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x80000008 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x80000008 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
Attached scsi removable disk sdd at scsi4, channel 0, id 0, lun 1
Attached scsi generic sg3 at scsi4, channel 0, id 0, lun 1, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:2)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 18 (level, low) -> IRQ 18
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7667 Fri Jun 17
07:01:04 PDT 2005
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 18
Warning, mounting filesystem with fatal errors, forcing read-only mount
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 19
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 2x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 2x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 2x mode
agpgart: Putting AGP V2 device at 0000:01:05.0 into 2x mode
CPU0 CPU1
0: 10449 3310533 IO-APIC-edge timer
1: 3457 4 IO-APIC-edge i8042
9: 0 0 IO-APIC-level acpi
12: 53486 25 IO-APIC-edge i8042
14: 20 1 IO-APIC-edge ide0
15: 102785 15 IO-APIC-edge ide1
17: 14579 4 IO-APIC-level libata
18: 343190 0 IO-APIC-level CS46XX, nvidia
19: 34384 13 IO-APIC-level ohci_hcd:usb1, eth0
NMI: 0 0
LOC: 3320994 3320993
ERR: 0
MIS: 0
Module Size Used by
snd_seq_midi 7072 0
snd_pcm_oss 48544 0
snd_mixer_oss 17664 1 snd_pcm_oss
snd_seq_oss 35072 0
snd_seq_midi_event 6144 2 snd_seq_midi,snd_seq_oss
snd_seq 52368 5 snd_seq_midi,snd_seq_oss,snd_seq_midi_event
snd_cs46xx 84552 3
snd_rawmidi 21152 2 snd_seq_midi,snd_cs46xx
snd_seq_device 7564 4 snd_seq_midi,snd_seq_oss,snd_seq,snd_rawmidi
snd_ac97_codec 83452 1 snd_cs46xx
snd_pcm 83332 4 snd_pcm_oss,snd_cs46xx,snd_ac97_codec
snd_timer 22020 2 snd_seq,snd_pcm
snd 48612 15
snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_cs46xx,snd_rawmidi,snd_seq_device,snd_ac97_codec,snd_pcm,snd_timer
snd_page_alloc 8068 2 snd_cs46xx,snd_pcm
nvidia 3707524 12
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P]
System Controller (rev 11)
Flags: bus master, 66Mhz, medium devsel, latency 32
Memory at ec000000 (32-bit, prefetchable)
Memory at ea200000 (32-bit, prefetchable) [size=4K]
I/O ports at 1410 [disabled] [size=4]
Capabilities: <available only to root>
00: 22 10 0c 70 06 00 30 22 11 00 00 06 00 20 00 00
10: 08 00 00 ec 08 00 20 ea 11 14 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP
Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: e9000000-e9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
00: 22 10 0d 70 07 00 20 02 00 00 04 06 00 63 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 f1 01 20 22
20: 00 e9 f0 e9 00 f0 f0 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 0c 00
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev
05)
Flags: bus master, 66Mhz, medium devsel, latency 0
00: 22 10 40 74 0f 00 20 02 05 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
(rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
Flags: bus master, medium devsel, latency 0
I/O ports at f000 [size=16]
00: 22 10 41 74 05 00 00 02 04 8a 01 01 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 22 10 41 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI
Flags: medium devsel
00: 22 10 43 74 00 00 80 02 03 00 80 06 00 16 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 43 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 20
I/O ports at 1000
Memory at e8000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
00: ec 10 69 81 17 00 b0 02 10 00 00 02 10 40 00 00
10: 01 10 00 00 00 00 00 e8 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 69 81
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 20 40
0000:00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev
05) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=168
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ea000000-ea1fffff
Expansion ROM at 00002000 [disabled] [size=4K]
00: 22 10 48 74 17 00 20 22 05 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 a8 20 20 00 22
20: 00 ea 10 ea f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 04 00
0000:01:05.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80cf
Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 18
Memory at e9000000 (32-bit, non-prefetchable)
Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <available only to root>
00: de 10 22 03 07 00 b0 02 a1 00 00 03 00 f8 00 00
10: 00 00 00 e9 08 00 00 f0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 cf 80
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 05 01
0000:02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
(rev 07) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at ea120000 (32-bit, non-prefetchable)
00: 22 10 49 74 17 00 80 82 07 10 03 0c 00 40 00 00
10: 00 00 12 ea 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 49 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 04 00 50
0000:02:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 16
I/O ports at 2000
Memory at ea123000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
00: ec 10 39 81 07 00 90 02 10 00 00 02 00 40 00 00
10: 01 20 00 00 00 30 12 ea 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 20 40
0000:02:05.0 RAID bus controller: Promise Technology, Inc. PDC20319 (FastTrak
S150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20319 (FastTrak S150 TX4)
Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 17
I/O ports at 2800
I/O ports at 2840 [size=16]
I/O ports at 2400 [size=128]
Memory at ea121000 (32-bit, non-prefetchable) [size=4K]
Memory at ea100000 (32-bit, non-prefetchable) [size=128K]
Capabilities: <available only to root>
00: 5a 10 19 33 17 00 30 02 02 00 04 01 90 60 00 00
10: 01 28 00 00 41 28 00 00 01 24 00 00 00 10 12 ea
20: 00 00 10 ea 00 00 00 00 00 00 00 00 5a 10 19 33
30: 00 00 00 00 60 00 00 00 00 00 00 00 09 01 04 12
0000:02:06.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24
[CrystalClear SoundFusion Audio Accelerator] (rev 01)
Subsystem: Voyetra Technologies: Unknown device 3357
Flags: bus master, slow devsel, latency 64, IRQ 18
Memory at ea122000 (32-bit, non-prefetchable)
Memory at ea000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
00: 13 10 03 60 06 00 10 04 01 00 01 04 00 40 00 00
10: 00 20 12 ea 00 00 00 ea 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 53 50 57 33
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 04 18
0000:02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 78)
Subsystem: Tyan Computer Tiger MPX S2466 (3C920 Integrated Fast
Ethernet Controller)
Flags: bus master, medium devsel, latency 80, IRQ 19
I/O ports at 2480
Memory at ea123400 (32-bit, non-prefetchable) [size=128]
Capabilities: <available only to root>
00: b7 10 00 92 17 00 10 02 78 00 00 02 10 50 00 00
10: 81 24 00 00 00 34 12 ea 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 66 24
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 0a 0a
