Yes my card does have the SCSI connector for the external drive which I don't use and the 15 pin for the breakout box.
When you say switch is it physical? Do I need to set it to a certain config? Thanks, On Sun., Mar. 21, 2021, 11:33 a.m. Bernhard Praschinger, < shadowl...@utanet.at> wrote: > Hallo, > > sorry I was offline for quite a while. > > You write in the subject that you have a Iomega Buz card, but the lspci > output say's ZR36057. Which was used in the DC10/DC30. Does your card > have a SCSI interface connector and a 15 pin connector on the backplane ? > The buz was the most problematic card, because it had a PCI Switch on > the card for the ZR36067 and the SCSI controller. > > William Lum wrote: > > Hello, > > > > Following your instructions here is what I found. > > > > I should also note that I am testing on a live USB stick vs installed on > > ssd. This was mainly because I had installed 3-5 different versions and > > flavours of linux trying to get this to work and wanted to avoid > > installing more until I find a solution. Please let me know if this is > > an issue. > > > > On Ubuntu 15.04 (Linux ubuntu 3.19.0-15-generic) > > The hardware is the IOmega Buz (0.6:09.0 Multimedia video controller > > [0400]: Zoran Corporation *ZR36057*PQC Video cutting chipset [11de:6057] > > (rev 01) > > > > I looked for drivers in /lib/modules/ that took me to > > /lib/modules/3.19.0-15-generic/kernel/driver/media/pci/zoran where I > found: > > - videocodec.ko > > - zr36016.ko > > - zr36050.ko > > - zr36060.ko > > - zr36067.ko > > none seem to be a direct match for the zr36057 > That should be no problem just use the zr36067 instead. > > > Tried to load the driver "modprobe -n -v --show-depends zoran" this > > resulted "FATAL: Module zoran not found." > > > > Then tried "modprobe -n -v --show-depends zr36067" this seemed to > > install modules > > insmod /lib/modeules/3.19.0-15-generic/kernel/driver/...ko (ic2/alogo, > > media, V4l2, videocodec, zr36067) > It should also load the driver for the TV decoder and encoder. > > When you do a lsmod | grep zr you should see the loaded modules. Are > some v4l (video4linux) modules loaded too ? > > > but when I "lspci -nnk" it still does not show any subsystem or driver > > in use so not sure if it worked... also wanted to try testing it with > > VLC but couldn't install as the Ubuntu software center is too old and > > the links no longer seem to work. This worries me, if I do get this > > working will I be able to install any software (i.e. Kdenlive etc). > > Don;t know how to do this if the ubuntu software center isn't working. > > apt get also had errors as the folders for this version of ubuntu seem > > to no longer exist. > I don't know if it is a problem if the lspci does not show you the card. > Does the lspci command (or some boot log) show you a hint that the scsi > controller ist recognized. > > When you start in a 2nd terminal a command like that: > tail -f /var/log/messages > > You should see the messages when the kernel loads the driver. That > output would be very helpful. > > > Thoughts on how I should proceed? > The output from the kernel when you load the drivers should be very > helpful. To see if that kernel recognizes the card. > > > auf hoffentlich bald, > > Berni the Chaos of Woodquarter > > Email: shadowl...@utanet.at > www: http://www.lysator.liu.se/~gz/bernhard >
_______________________________________________ Mjpeg-users mailing list Mjpeg-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/mjpeg-users
