Hi list,
I'm a bit (only a bit) desperate in getting a VLAN setup running on a PC
Engines Alix Board (dmesg below).
Simply put, I need vlan 123 on both vr0 and vr2 (the Alix I use has three NICs,
vr0 to vr2).
Unfortunately, I only seem to get vlan 123 set up on either vr0 or vr2. I tried
different approaches, however I failed.
I'm pretty sure that it's a trivial thing, but I don't see it.
#cat /etc/hostname.vlan123
inet 222.111.222.111 255.255.255.0 NONE vlan 123 vlandev vr2
inet 10.11.0.3 255.255.255.0 NONE vlan 123 vlandev vr0
When booting, I get:
ifconfig: SIOCSETVLAN: Device busy
ifconfig: SIOCAIFADDR: Can't assign requested address
Setting
inet alias 10.11.0.3 255.255.255.0 NONE vlan 123 vlandev vr0
also doesn't help.
How can I get vlan 123 on both vr0 and vr2?
Thanks for your help,
Donald
---
dmesg:
OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 499
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 268009472 (255MB)
avail mem = 250859520 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/10/07, BIOS32 rev. 0 @ 0xfceb2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10, address
00:0d:b9:15:98:14
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:0d:b9:15:98:15
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:0d:b9:15:98:16
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 0, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <TRANSCEND>
wd0: 1-sector PIO, LBA, 955MB, 1957536 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15, version 1.0,
legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e3ef netmask ffef ttymask ffff
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
clock: unknown CMOS layout
--
GRATIS f|r alle GMX-Mitglieder: Die maxdome Movie-FLAT!
Jetzt freischalten unter http://portal.gmx.net/de/go/maxdome01
