Hello,
I believe that these disks are SATA II
(http://www.seagate.com/ww/v/index.jsp?vgnextoid=6278576e14ee9110VgnVCM100000
f5ee0a0aRCRD)
and thus would always fall under wd driver as per the man page.
I believe that sd is for scsi only. Is this assumption correct?
Andres
On Tue, Feb 23, 2010 at 3:36 PM, Marco Peereboom <sl...@peereboom.us> wrote:
> Your disks are still wd so io sucks. Use -current.
>
> On Tue, Feb 23, 2010 at 03:22:28PM -0600, Andres Salazar wrote:
>> Hello,
>>
>> I had a R201 running in 4.6 i386 stable..I was told this configuration
>> was very new.. so I got a new box this time its a PowerEdge is R200
>> without any special PCI SATA controller. With 2 SATA II Hard Disks.
>> BIOS Sata setting is set to be in ATA Mode (its either this or OFF).
>>
>> Either after all this change, and a clean install the IO is 55%
>> greater then all my other machines. For example a userland recompile
>> takes 55min , vrs the same proc and ram on another box is 35 min.
>>
>> Below is my dmesg.. which I dont see any flag?? Possibly there must be
>> some incompatibility with the hard disk?
>>
>> OpenBSD 4.6-stable (GENERIC-13-12-09.MP) #0: Tue Feb 23 16:08:43 CST 2010
>> r...@bazz.my.domain:/usr/src/sys/arch/i386/compile/GENERIC-13-12-09.MP
>> cpu0: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67
GHz
>> cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,C
X16,xTPR
>> real mem = 3487866880 (3326MB)
>> avail mem = 3383250944 (3226MB)
>> mainbus0 at root
>> bios0 at mainbus0: AT/286+ BIOS, date 05/15/09, BIOS32 rev. 0 @
>> 0xfac90, SMBIOS rev. 2.5 @ 0xcff9c000 (46 entries)
>> bios0: vendor Dell Inc. version "1.4.3" date 05/15/2009
>> bios0: Dell Inc. PowerEdge R200
>> acpi0 at bios0: rev 2
>> acpi0: tables DSDT FACP APIC SPCR HPET MCFG WD__ SLIC ERST HEST BERT
>> EINJ SSDT SSDT SSDT SSDT SSDT
>> acpi0: wakeup devices PCI0(S5)
>> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>> cpu0 at mainbus0: apid 0 (boot processor)
>> cpu0: apic clock running at 333MHz
>> cpu1 at mainbus0: apid 1 (application processor)
>> cpu1: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67
GHz
>> cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,C
X16,xTPR
>> cpu2 at mainbus0: apid 2 (application processor)
>> cpu2: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67
GHz
>> cpu2:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,C
X16,xTPR
>> cpu3 at mainbus0: apid 3 (application processor)
>> cpu3: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67
GHz
>> cpu3:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,C
X16,xTPR
>> ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
>> ioapic0: misconfigured as apic 0, remapped to apid 4
>> acpihpet0 at acpi0: 14318179 Hz
>> acpiprt0 at acpi0: bus 0 (PCI0)
>> acpiprt1 at acpi0: bus 1 (PEX1)
>> acpiprt2 at acpi0: bus 2 (SBE0)
>> acpiprt3 at acpi0: bus 3 (SBE4)
>> acpiprt4 at acpi0: bus 4 (SBE5)
>> acpiprt5 at acpi0: bus 5 (COMP)
>> acpicpu0 at acpi0: PSS
>> acpicpu1 at acpi0: PSS
>> acpicpu2 at acpi0: PSS
>> acpicpu3 at acpi0: PSS
>> bios0: ROM list: 0xc0000/0x9000 0xc9000/0x1000 0xca000/0x1800
0xec000/0x4000!
>> ipmi at mainbus0 not configured
>> cpu0: Enhanced SpeedStep 2667 MHz: speeds: 2667, 2333, 2000 MHz
>> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
>> pchb0 at pci0 dev 0 function 0 "Intel 3200/3210 Host" rev 0x01
>> ppb0 at pci0 dev 1 function 0 "Intel 3200/3210 PCIE" rev 0x01: apic 4
>> int 16 (irq 15)
>> pci1 at ppb0 bus 1
>> ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4
>> int 16 (irq 15)
>> pci2 at ppb1 bus 2
>> ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02
>> pci3 at ppb2 bus 3
>> bge0 at pci3 dev 0 function 0 "Broadcom BCM5721" rev 0x21, BCM5750 C1
>> (0x4201): apic 4 int 16 (irq 15), address 00:25:64:3c:7f:8c
>> brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
>> ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02
>> pci4 at ppb3 bus 4
>> bge1 at pci4 dev 0 function 0 "Broadcom BCM5721" rev 0x21, BCM5750 C1
>> (0x4201): apic 4 int 17 (irq 14), address 00:25:64:3c:7f:8d
>> brgphy1 at bge1 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
>> uhci0 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4
>> int 21 (irq 11)
>> uhci1 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4
>> int 20 (irq 10)
>> uhci2 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4
>> int 21 (irq 11)
>> ehci0 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4
>> int 21 (irq 11)
>> usb0 at ehci0: USB revision 2.0
>> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>> ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
>> pci5 at ppb4 bus 5
>> vga1 at pci5 dev 5 function 0 "ATI ES1000" rev 0x02
>> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
>> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
>> radeondrm0 at vga1: apic 4 int 19 (irq 5)
>> drm0 at radeondrm0
>> ichpcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02: PM
disabled
>> pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA,
>> channel 0 configured to native-PCI, channel 1 configured to native-PCI
>> pciide0: using apic 4 int 23 (irq 6) for native-PCI interrupt
>> wd0 at pciide0 channel 0 drive 0: <ST3250310NS>
>> wd0: 16-sector PIO, LBA48, 238418MB, 488281250 sectors
>> atapiscsi0 at pciide0 channel 0 drive 1
>> scsibus0 at atapiscsi0: 2 targets
>> cd0 at scsibus0 targ 0 lun 0: <TEAC, DVD-ROM DV28SV, D.0K> ATAPI
>> 5/cdrom removable
>> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
>> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
>> wd1 at pciide0 channel 1 drive 0: <ST3250310NS>
>> wd1: 16-sector PIO, LBA48, 238418MB, 488281250 sectors
>> wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
>> usb1 at uhci0: USB revision 1.0
>> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb2 at uhci1: USB revision 1.0
>> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb3 at uhci2: USB revision 1.0
>> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> isa0 at ichpcib0
>> isadma0 at isa0
>> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>> pckbc0 at isa0 port 0x60/5
>> pckbd0 at pckbc0 (kbd slot)
>> pckbc0: using irq 1 for kbd slot
>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>> pmsi0 at pckbc0 (aux slot)
>> pckbc0: using irq 12 for aux slot
>> wsmouse0 at pmsi0 mux 0
>> pcppi0 at isa0 port 0x61
>> midi0 at pcppi0: <PC speaker>
>> spkr0 at pcppi0
>> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
>> mtrr: Pentium Pro MTRR support
>> uhub4 at uhub0 port 5 "Cypress Semiconductor USB2 Hub" rev 2.00/0.0b addr
2
>> softraid0 at root
>> root on wd1a swap on wd1b dump on wd1b
>>
>>
>> Andres
