Your disks are still wd so io sucks. Use -current.
On Tue, Feb 23, 2010 at 03:22:28PM -0600, Andres Salazar wrote:
> Hello,
>
> I had a R201 running in 4.6 i386 stable..I was told this configuration
> was very new.. so I got a new box this time its a PowerEdge is R200
> without any special PCI SATA controller. With 2 SATA II Hard Disks.
> BIOS Sata setting is set to be in ATA Mode (its either this or OFF).
>
> Either after all this change, and a clean install the IO is 55%
> greater then all my other machines. For example a userland recompile
> takes 55min , vrs the same proc and ram on another box is 35 min.
>
> Below is my dmesg.. which I dont see any flag?? Possibly there must be
> some incompatibility with the hard disk?
>
> OpenBSD 4.6-stable (GENERIC-13-12-09.MP) #0: Tue Feb 23 16:08:43 CST 2010
> r...@bazz.my.domain:/usr/src/sys/arch/i386/compile/GENERIC-13-12-09.MP
> cpu0: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67 GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,CX16,xTPR
> real mem = 3487866880 (3326MB)
> avail mem = 3383250944 (3226MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 05/15/09, BIOS32 rev. 0 @
> 0xfac90, SMBIOS rev. 2.5 @ 0xcff9c000 (46 entries)
> bios0: vendor Dell Inc. version "1.4.3" date 05/15/2009
> bios0: Dell Inc. PowerEdge R200
> acpi0 at bios0: rev 2
> acpi0: tables DSDT FACP APIC SPCR HPET MCFG WD__ SLIC ERST HEST BERT
> EINJ SSDT SSDT SSDT SSDT SSDT
> acpi0: wakeup devices PCI0(S5)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: apic clock running at 333MHz
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67 GHz
> cpu1:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,CX16,xTPR
> cpu2 at mainbus0: apid 2 (application processor)
> cpu2: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67 GHz
> cpu2:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,CX16,xTPR
> cpu3 at mainbus0: apid 3 (application processor)
> cpu3: Intel(R) Xeon(R) CPU X3330 @ 2.66GHz ("GenuineIntel" 686-class) 2.67 GHz
> cpu3:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,CX16,xTPR
> ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
> ioapic0: misconfigured as apic 0, remapped to apid 4
> acpihpet0 at acpi0: 14318179 Hz
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (PEX1)
> acpiprt2 at acpi0: bus 2 (SBE0)
> acpiprt3 at acpi0: bus 3 (SBE4)
> acpiprt4 at acpi0: bus 4 (SBE5)
> acpiprt5 at acpi0: bus 5 (COMP)
> acpicpu0 at acpi0: PSS
> acpicpu1 at acpi0: PSS
> acpicpu2 at acpi0: PSS
> acpicpu3 at acpi0: PSS
> bios0: ROM list: 0xc0000/0x9000 0xc9000/0x1000 0xca000/0x1800 0xec000/0x4000!
> ipmi at mainbus0 not configured
> cpu0: Enhanced SpeedStep 2667 MHz: speeds: 2667, 2333, 2000 MHz
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Intel 3200/3210 Host" rev 0x01
> ppb0 at pci0 dev 1 function 0 "Intel 3200/3210 PCIE" rev 0x01: apic 4
> int 16 (irq 15)
> pci1 at ppb0 bus 1
> ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4
> int 16 (irq 15)
> pci2 at ppb1 bus 2
> ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02
> pci3 at ppb2 bus 3
> bge0 at pci3 dev 0 function 0 "Broadcom BCM5721" rev 0x21, BCM5750 C1
> (0x4201): apic 4 int 16 (irq 15), address 00:25:64:3c:7f:8c
> brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
> ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02
> pci4 at ppb3 bus 4
> bge1 at pci4 dev 0 function 0 "Broadcom BCM5721" rev 0x21, BCM5750 C1
> (0x4201): apic 4 int 17 (irq 14), address 00:25:64:3c:7f:8d
> brgphy1 at bge1 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
> uhci0 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4
> int 21 (irq 11)
> uhci1 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4
> int 20 (irq 10)
> uhci2 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4
> int 21 (irq 11)
> ehci0 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4
> int 21 (irq 11)
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
> pci5 at ppb4 bus 5
> vga1 at pci5 dev 5 function 0 "ATI ES1000" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> radeondrm0 at vga1: apic 4 int 19 (irq 5)
> drm0 at radeondrm0
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02: PM disabled
> pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA,
> channel 0 configured to native-PCI, channel 1 configured to native-PCI
> pciide0: using apic 4 int 23 (irq 6) for native-PCI interrupt
> wd0 at pciide0 channel 0 drive 0: <ST3250310NS>
> wd0: 16-sector PIO, LBA48, 238418MB, 488281250 sectors
> atapiscsi0 at pciide0 channel 0 drive 1
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <TEAC, DVD-ROM DV28SV, D.0K> ATAPI
> 5/cdrom removable
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
> wd1 at pciide0 channel 1 drive 0: <ST3250310NS>
> wd1: 16-sector PIO, LBA48, 238418MB, 488281250 sectors
> wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> mtrr: Pentium Pro MTRR support
> uhub4 at uhub0 port 5 "Cypress Semiconductor USB2 Hub" rev 2.00/0.0b addr 2
> softraid0 at root
> root on wd1a swap on wd1b dump on wd1b
>
>
> Andres
