On Sun, Nov 8, 2009 at 10:06 AM, Donald Allen <donaldcal...@gmail.com> wrote:
> On Thu, Nov 5, 2009 at 10:05 AM, Marco Peereboom <sl...@peereboom.us>
wrote:
>> If I read yor report correctly this was fixed past 4.6. Try booting a
>> -current kernel and see if it works.
Clues:
1. Logged in as me and moving /etc/rc.shutdown ->
/etc/rc.shutdown.save and then did sudo reboot. No help.
2. Immediately after reboot, logged in as root, mv'ed
/etc/rc.shutdown.save -> /etc/rc.shutdown and did a 'reboot'. No help.
3. Built a copy of /usr/src/sbin/reboot.c in a separate directory,
compiled with -g, and ran under gdb with a breakpoint at
/* Log the reboot. */'
--> if (!lflag) {
At this point, howto was 0, as you'd expect. dohalt was also 0. Things
get a little hairy after that, so I didn't proceed, but based on the
state of things at the breakpoint, a quick look at the subsequent code
suggests (unless I missed something) that the howto arg in the call to
reboot was still 0.
That's as far as I've gotten and can't work on this further today.
/Don
>
> I just installed the latest snapshot on the machine and did a test
> reboot and the problem remains -- brief powerdown before rebooting.
> After I had completed the update and rebooted while running the kernel
> on the install46 cd, the powerdown did not occur. This is exactly the
> behavior I've seen since 4.5 release.
>
> I'm guessing that there's something about my configuration that's
> causing this, since I believe the installed kernel and the kernel on
> the CD are essentially the same (though I do understand that booting
> from the CD runs bsd.rd whereas booting from the system's disk runs
> bsd.mp, but since I'm already guessing, I'll go further out on the
> limb and guess that is not the issue, as I would think that the code
> that talks to the hardware to initiate the reboot would be the same).
> I'm going to try to find the shutdown/reboot code in the kernel and
> have a look (I've done a lot of OS development in my long career, so
> this is not quite as crazy as it might otherwise sound) to try to get
> a clue as to what in my configuration might be causing this.
>
> In the meanwhile, I'd appreciate any other suggestions.
>
> Thanks --
> /Don Allen
>
>>
>> On Thu, Nov 05, 2009 at 08:58:10AM -0500, Donald Allen wrote:
>>> I'm running 4.6 stable on a Lenovo S10 Workstation (dmesg output
>>> below). If I 'sudo reboot' on this machine, the system powers down
>>> briefly (a few seconds) before rebooting. However, if I boot the
>>> machine with a CD made from the amd64 version of install46.iso, go to
>>> the shell and 'reboot' from there, the machine reboots normally. My
>>> rc.shutdown:
>>>
>>> # $OpenBSD: rc.shutdown,v 1.3 2009/10/21 16:56:46 dca Exp $
>>> #
>>> # If it exists, this script is run at system-shutdown by reboot(8),
>>> # halt(8). If the architecture supports keyboard requested halting,
>>> # it is also run by init(8) when such an event happens.
>>> #
>>>
>>> powerdown=NO # set to YES for powerdown
>>>
>>> #
>>> # Your shell code goes here
>>> #
>>>
>>> ##Postgresql
>>> if [ -f /var/postgresql/data/postmaster.pid ]; then
>>> su -l _postgresql -c "/usr/local/bin/pg_ctl stop -m fast \
>>> -D /var/postgresql/data"
>>> rm -f /var/postgresql/data/postmaster.pid
>>> fi
>>>
>>> This was also an issue when I had 4.5 release running on this machine.
>>> This problem does not happen on my Thinkpad X61 (Core 2 Duo
>>> processor), set up similarly (4.6 stable).
>>>
>>> Suggestions?
>>>
>>> /Don Allen
>>>
>>> dmesg output:
>>>
>>> OpenBSD 4.6-stable (GENERIC) #0: Fri Oct 30 12:09:11 EDT 2009
>>> r...@salome.comcast.net:/usr/src/sys/arch/amd64/compile/GENERIC
>>> real mem = 2681602048 (2557MB)
>>> avail mem = 2585251840 (2465MB)
>>> mainbus0 at root
>>> bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xefcc0 (45 entries)
>>> bios0: vendor LENOVO version "2WKT27A" date 01/31/2008
>>> bios0: LENOVO 6423CTO
>>> acpi0 at bios0: rev 2
>>> acpi0: tables DSDT FACP TCPA _MAR MCFG HPET APIC BOOT SSDT SSDT SSDT
>>> SSDT SSDT SSDT SSDT SSDT SSDT
>>> acpi0: wakeup devices USB4(S3) USB5(S3) USB7(S3) ESB2(S3) HDEF(S5)
>>> EXP1(S4) EXP2(S4) EXP3(S4) EXP4(S4) EXP5(S4) EXP6(S4) USB1(S3)
>>> USB2(S3) USB3(S3) USB6(S3) ESB1(S3) PCIB(S5) KBC0(S4) MSE0(S4)
>>> COM1(S4) COM2(S4) PWRB(S3)
>>> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>>> acpihpet0 at acpi0: 14318179 Hz
>>> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>>> cpu0 at mainbus0: apid 0 (boot processor)
>>> cpu0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz, 42374.36 MHz
>>> cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX16,
xTPR,NXE,LONG
>>> cpu0: 4MB 64b/line 16-way L2 cache
>>> cpu0: apic clock running at 265MHz
>>> cpu at mainbus0: not configured
>>> cpu at mainbus0: not configured
>>> cpu at mainbus0: not configured
>>> ioapic0 at mainbus0 apid 4 pa 0xfec00000, version 20, 24 pins
>>> acpiprt0 at acpi0: bus 0 (PCI0)
>>> acpiprt1 at acpi0: bus 1 (PEG1)
>>> acpiprt2 at acpi0: bus -1 (PEG2)
>>> acpiprt3 at acpi0: bus 5 (EXP1)
>>> acpiprt4 at acpi0: bus -1 (EXP2)
>>> acpiprt5 at acpi0: bus -1 (EXP3)
>>> acpiprt6 at acpi0: bus -1 (EXP4)
>>> acpiprt7 at acpi0: bus 13 (EXP5)
>>> acpiprt8 at acpi0: bus 15 (EXP6)
>>> acpiprt9 at acpi0: bus 17 (PCIB)
>>> acpicpu0 at acpi0: C3, PSS
>>> acpibtn0 at acpi0: PWRB
>>> cpu0: Enhanced SpeedStep 42374 MHz: speeds: 2400, 1600 MHz
>>> pci0 at mainbus0 bus 0
>>> pchb0 at pci0 dev 0 function 0 "Intel 82X38 Host" rev 0x01
>>> ppb0 at pci0 dev 1 function 0 "Intel 82X38 PCIE" rev 0x01: apic 4 int 16
(irq 5)
>>> pci1 at ppb0 bus 1
>>> vga1 at pci1 dev 0 function 0 vendor "NVIDIA", unknown product 0x040a rev
0xa1
>>> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
>>> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
>>> uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: apic 4
>>> int 16 (irq 5)
>>> uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: apic 4
>>> int 17 (irq 3)
>>> ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: apic 4
>>> int 18 (irq 10)
>>> usb0 at ehci0: USB revision 2.0
>>> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>>> azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x02:
>>> apic 4 int 16 (irq 5)
>>> azalia0: codecs: Analog Devices AD1988A
>>> audio0 at azalia0
>>> ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4
>>> int 16 (irq 5)
>>> pci2 at ppb1 bus 5
>>> mpi0 at pci2 dev 0 function 0 "Symbios Logic SAS1064E" rev 0x08: apic
>>> 4 int 16 (irq 5)
>>> scsibus0 at mpi0: 112 targets
>>> sd0 at scsibus0 targ 0 lun 0: <LSILOGIC, Logical Volume, 3000> SCSI2
>>> 0/direct fixed
>>> sd0: 278472MB, 512 bytes/sec, 570310656 sec total
>>> ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: apic 4
>>> int 16 (irq 5)
>>> pci3 at ppb2 bus 13
>>> bge0 at pci3 dev 0 function 0 "Broadcom BCM5755" rev 0x02, BCM5755 A2
>>> (0xa002): apic 4 int 16 (irq 5), address 00:1e:37:f4:31:c8
>>> brgphy0 at bge0 phy 1: BCM5755 10/100/1000baseT PHY, rev. 0
>>> ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02: apic 4
>>> int 17 (irq 3)
>>> pci4 at ppb3 bus 15
>>> bge1 at pci4 dev 0 function 0 "Broadcom BCM5754" rev 0x02,
>>> BCM5754/5787 A2 (0xb002): apic 4 int 17 (irq 3), address
>>> 00:1e:37:f4:31:c9
>>> brgphy1 at bge1 phy 1: BCM5787 10/100/1000baseT PHY, rev. 0
>>> uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4
>>> int 16 (irq 5)
>>> uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4
>>> int 17 (irq 3)
>>> uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4
>>> int 18 (irq 10)
>>> uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x02: apic 4
>>> int 19 (irq 11)
>>> ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4
>>> int 16 (irq 5)
>>> usb1 at ehci1: USB revision 2.0
>>> uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>>> ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
>>> pci5 at ppb4 bus 17
>>> "TI TSB43AB23 FireWire" rev 0x00 at pci5 dev 10 function 0 not configured
>>> "TI TSB43AB22 FireWire" rev 0x00 at pci5 dev 13 function 0 not configured
>>> pcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02
>>> pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA,
>>> channel 0 configured to native-PCI, channel 1 configured to native-PCI
>>> pciide0: using apic 4 int 17 (irq 255) for native-PCI interrupt
>>> atapiscsi0 at pciide0 channel 0 drive 0
>>> scsibus1 at atapiscsi0: 2 targets
>>> cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM GSA-H60N, CX04> ATAPI
>>> 5/cdrom removable
>>> cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
>>> ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x02: apic
>>> 4 int 18 (irq 10)
>>> iic0 at ichiic0
>>> sdtemp0 at iic0 addr 0x18: stts424e02
>>> sdtemp1 at iic0 addr 0x19: stts424e02
>>> sdtemp2 at iic0 addr 0x1a: stts424e02
>>> sdtemp3 at iic0 addr 0x1b: stts424e02
>>> adt0 at iic0 addr 0x2e: sch5027 rev 0x69
>>> spdmem0 at iic0 addr 0x50: 1GB DDR3 SDRAM ECC PC3-8500
>>> spdmem1 at iic0 addr 0x51: 1GB DDR3 SDRAM ECC PC3-8500
>>> spdmem2 at iic0 addr 0x52: 1GB DDR3 SDRAM ECC PC3-8500
>>> spdmem3 at iic0 addr 0x53: 1GB DDR3 SDRAM ECC PC3-8500
>>> pciide1 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA,
>>> channel 0 wired to native-PCI, channel 1 wired to native-PCI
>>> pciide1: using apic 4 int 17 (irq 3) for native-PCI interrupt
>>> "Intel 82801I Thermal" rev 0x02 at pci0 dev 31 function 6 not configured
>>> usb2 at uhci0: USB revision 1.0
>>> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> usb3 at uhci1: USB revision 1.0
>>> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> usb4 at uhci2: USB revision 1.0
>>> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> usb5 at uhci3: USB revision 1.0
>>> uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> usb6 at uhci4: USB revision 1.0
>>> uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> usb7 at uhci5: USB revision 1.0
>>> uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>>> isa0 at pcib0
>>> isadma0 at isa0
>>> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>>> pckbc0 at isa0 port 0x60/5
>>> pckbd0 at pckbc0 (kbd slot)
>>> pckbc0: using irq 1 for kbd slot
>>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>>> pcppi0 at isa0 port 0x61
>>> midi0 at pcppi0: <PC speaker>
>>> spkr0 at pcppi0
>>> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
>>> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
>>> mtrr: Pentium Pro MTRR support
>>> uhub8 at uhub1 port 2 "NEC product 0x005a" rev 2.00/1.00 addr 2
>>> uhub9 at uhub8 port 3 "ATEN International product 0x7000" rev 1.10/1.00
addr 3
>>> uhidev0 at uhub9 port 1 configuration 1 interface 0 "Microsoft
>>> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4
>>> uhidev0: iclass 3/1
>>> ukbd0 at uhidev0: 8 modifier keys, 6 key codes
>>> wskbd1 at ukbd0 mux 1
>>> wskbd1: connecting to wsdisplay0
>>> uhidev1 at uhub9 port 1 configuration 1 interface 1 "Microsoft
>>> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4
>>> uhidev1: iclass 3/0, 1 report id
>>> uhid0 at uhidev1 reportid 1: input=7, output=0, feature=0
>>> uhidev2 at uhub9 port 1 configuration 1 interface 2 "Microsoft
>>> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4
>>> uhidev2: iclass 3/1
>>> ums0 at uhidev2: 5 buttons, Z dir
>>> wsmouse0 at ums0 mux 0
>>> softraid0 at root
>>> root on sd0a swap on sd0b dump on sd0b
>>> uhub10 at uhub8 port 2 "D-Link product 0xf103" rev 2.00/1.00 addr 5
