On Thu, Nov 5, 2009 at 10:05 AM, Marco Peereboom <sl...@peereboom.us> wrote: > If I read yor report correctly this was fixed past 4.6. Try booting a > -current kernel and see if it works.
I just installed the latest snapshot on the machine and did a test reboot and the problem remains -- brief powerdown before rebooting. After I had completed the update and rebooted while running the kernel on the install46 cd, the powerdown did not occur. This is exactly the behavior I've seen since 4.5 release. I'm guessing that there's something about my configuration that's causing this, since I believe the installed kernel and the kernel on the CD are essentially the same (though I do understand that booting from the CD runs bsd.rd whereas booting from the system's disk runs bsd.mp, but since I'm already guessing, I'll go further out on the limb and guess that is not the issue, as I would think that the code that talks to the hardware to initiate the reboot would be the same). I'm going to try to find the shutdown/reboot code in the kernel and have a look (I've done a lot of OS development in my long career, so this is not quite as crazy as it might otherwise sound) to try to get a clue as to what in my configuration might be causing this. In the meanwhile, I'd appreciate any other suggestions. Thanks -- /Don Allen > > On Thu, Nov 05, 2009 at 08:58:10AM -0500, Donald Allen wrote: >> I'm running 4.6 stable on a Lenovo S10 Workstation (dmesg output >> below). If I 'sudo reboot' on this machine, the system powers down >> briefly (a few seconds) before rebooting. However, if I boot the >> machine with a CD made from the amd64 version of install46.iso, go to >> the shell and 'reboot' from there, the machine reboots normally. My >> rc.shutdown: >> >> # $OpenBSD: rc.shutdown,v 1.3 2009/10/21 16:56:46 dca Exp $ >> # >> # If it exists, this script is run at system-shutdown by reboot(8), >> # halt(8). If the architecture supports keyboard requested halting, >> # it is also run by init(8) when such an event happens. >> # >> >> powerdown=NO # set to YES for powerdown >> >> # >> # Your shell code goes here >> # >> >> ##Postgresql >> if [ -f /var/postgresql/data/postmaster.pid ]; then >> su -l _postgresql -c "/usr/local/bin/pg_ctl stop -m fast \ >> -D /var/postgresql/data" >> rm -f /var/postgresql/data/postmaster.pid >> fi >> >> This was also an issue when I had 4.5 release running on this machine. >> This problem does not happen on my Thinkpad X61 (Core 2 Duo >> processor), set up similarly (4.6 stable). >> >> Suggestions? >> >> /Don Allen >> >> dmesg output: >> >> OpenBSD 4.6-stable (GENERIC) #0: Fri Oct 30 12:09:11 EDT 2009 >> r...@salome.comcast.net:/usr/src/sys/arch/amd64/compile/GENERIC >> real mem = 2681602048 (2557MB) >> avail mem = 2585251840 (2465MB) >> mainbus0 at root >> bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xefcc0 (45 entries) >> bios0: vendor LENOVO version "2WKT27A" date 01/31/2008 >> bios0: LENOVO 6423CTO >> acpi0 at bios0: rev 2 >> acpi0: tables DSDT FACP TCPA _MAR MCFG HPET APIC BOOT SSDT SSDT SSDT >> SSDT SSDT SSDT SSDT SSDT SSDT >> acpi0: wakeup devices USB4(S3) USB5(S3) USB7(S3) ESB2(S3) HDEF(S5) >> EXP1(S4) EXP2(S4) EXP3(S4) EXP4(S4) EXP5(S4) EXP6(S4) USB1(S3) >> USB2(S3) USB3(S3) USB6(S3) ESB1(S3) PCIB(S5) KBC0(S4) MSE0(S4) >> COM1(S4) COM2(S4) PWRB(S3) >> acpitimer0 at acpi0: 3579545 Hz, 24 bits >> acpihpet0 at acpi0: 14318179 Hz >> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat >> cpu0 at mainbus0: apid 0 (boot processor) >> cpu0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz, 42374.36 MHz >> cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX16, xTPR,NXE,LONG >> cpu0: 4MB 64b/line 16-way L2 cache >> cpu0: apic clock running at 265MHz >> cpu at mainbus0: not configured >> cpu at mainbus0: not configured >> cpu at mainbus0: not configured >> ioapic0 at mainbus0 apid 4 pa 0xfec00000, version 20, 24 pins >> acpiprt0 at acpi0: bus 0 (PCI0) >> acpiprt1 at acpi0: bus 1 (PEG1) >> acpiprt2 at acpi0: bus -1 (PEG2) >> acpiprt3 at acpi0: bus 5 (EXP1) >> acpiprt4 at acpi0: bus -1 (EXP2) >> acpiprt5 at acpi0: bus -1 (EXP3) >> acpiprt6 at acpi0: bus -1 (EXP4) >> acpiprt7 at acpi0: bus 13 (EXP5) >> acpiprt8 at acpi0: bus 15 (EXP6) >> acpiprt9 at acpi0: bus 17 (PCIB) >> acpicpu0 at acpi0: C3, PSS >> acpibtn0 at acpi0: PWRB >> cpu0: Enhanced SpeedStep 42374 MHz: speeds: 2400, 1600 MHz >> pci0 at mainbus0 bus 0 >> pchb0 at pci0 dev 0 function 0 "Intel 82X38 Host" rev 0x01 >> ppb0 at pci0 dev 1 function 0 "Intel 82X38 PCIE" rev 0x01: apic 4 int 16 (irq 5) >> pci1 at ppb0 bus 1 >> vga1 at pci1 dev 0 function 0 vendor "NVIDIA", unknown product 0x040a rev 0xa1 >> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) >> wsdisplay0: screen 1-5 added (80x25, vt100 emulation) >> uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: apic 4 >> int 16 (irq 5) >> uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: apic 4 >> int 17 (irq 3) >> ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: apic 4 >> int 18 (irq 10) >> usb0 at ehci0: USB revision 2.0 >> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 >> azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x02: >> apic 4 int 16 (irq 5) >> azalia0: codecs: Analog Devices AD1988A >> audio0 at azalia0 >> ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4 >> int 16 (irq 5) >> pci2 at ppb1 bus 5 >> mpi0 at pci2 dev 0 function 0 "Symbios Logic SAS1064E" rev 0x08: apic >> 4 int 16 (irq 5) >> scsibus0 at mpi0: 112 targets >> sd0 at scsibus0 targ 0 lun 0: <LSILOGIC, Logical Volume, 3000> SCSI2 >> 0/direct fixed >> sd0: 278472MB, 512 bytes/sec, 570310656 sec total >> ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: apic 4 >> int 16 (irq 5) >> pci3 at ppb2 bus 13 >> bge0 at pci3 dev 0 function 0 "Broadcom BCM5755" rev 0x02, BCM5755 A2 >> (0xa002): apic 4 int 16 (irq 5), address 00:1e:37:f4:31:c8 >> brgphy0 at bge0 phy 1: BCM5755 10/100/1000baseT PHY, rev. 0 >> ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02: apic 4 >> int 17 (irq 3) >> pci4 at ppb3 bus 15 >> bge1 at pci4 dev 0 function 0 "Broadcom BCM5754" rev 0x02, >> BCM5754/5787 A2 (0xb002): apic 4 int 17 (irq 3), address >> 00:1e:37:f4:31:c9 >> brgphy1 at bge1 phy 1: BCM5787 10/100/1000baseT PHY, rev. 0 >> uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4 >> int 16 (irq 5) >> uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4 >> int 17 (irq 3) >> uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4 >> int 18 (irq 10) >> uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x02: apic 4 >> int 19 (irq 11) >> ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4 >> int 16 (irq 5) >> usb1 at ehci1: USB revision 2.0 >> uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 >> ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92 >> pci5 at ppb4 bus 17 >> "TI TSB43AB23 FireWire" rev 0x00 at pci5 dev 10 function 0 not configured >> "TI TSB43AB22 FireWire" rev 0x00 at pci5 dev 13 function 0 not configured >> pcib0 at pci0 dev 31 function 0 "Intel 82801IR LPC" rev 0x02 >> pciide0 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA, >> channel 0 configured to native-PCI, channel 1 configured to native-PCI >> pciide0: using apic 4 int 17 (irq 255) for native-PCI interrupt >> atapiscsi0 at pciide0 channel 0 drive 0 >> scsibus1 at atapiscsi0: 2 targets >> cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM GSA-H60N, CX04> ATAPI >> 5/cdrom removable >> cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 >> ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x02: apic >> 4 int 18 (irq 10) >> iic0 at ichiic0 >> sdtemp0 at iic0 addr 0x18: stts424e02 >> sdtemp1 at iic0 addr 0x19: stts424e02 >> sdtemp2 at iic0 addr 0x1a: stts424e02 >> sdtemp3 at iic0 addr 0x1b: stts424e02 >> adt0 at iic0 addr 0x2e: sch5027 rev 0x69 >> spdmem0 at iic0 addr 0x50: 1GB DDR3 SDRAM ECC PC3-8500 >> spdmem1 at iic0 addr 0x51: 1GB DDR3 SDRAM ECC PC3-8500 >> spdmem2 at iic0 addr 0x52: 1GB DDR3 SDRAM ECC PC3-8500 >> spdmem3 at iic0 addr 0x53: 1GB DDR3 SDRAM ECC PC3-8500 >> pciide1 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA, >> channel 0 wired to native-PCI, channel 1 wired to native-PCI >> pciide1: using apic 4 int 17 (irq 3) for native-PCI interrupt >> "Intel 82801I Thermal" rev 0x02 at pci0 dev 31 function 6 not configured >> usb2 at uhci0: USB revision 1.0 >> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> usb3 at uhci1: USB revision 1.0 >> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> usb4 at uhci2: USB revision 1.0 >> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> usb5 at uhci3: USB revision 1.0 >> uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> usb6 at uhci4: USB revision 1.0 >> uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> usb7 at uhci5: USB revision 1.0 >> uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >> isa0 at pcib0 >> isadma0 at isa0 >> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo >> pckbc0 at isa0 port 0x60/5 >> pckbd0 at pckbc0 (kbd slot) >> pckbc0: using irq 1 for kbd slot >> wskbd0 at pckbd0: console keyboard, using wsdisplay0 >> pcppi0 at isa0 port 0x61 >> midi0 at pcppi0: <PC speaker> >> spkr0 at pcppi0 >> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 >> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec >> mtrr: Pentium Pro MTRR support >> uhub8 at uhub1 port 2 "NEC product 0x005a" rev 2.00/1.00 addr 2 >> uhub9 at uhub8 port 3 "ATEN International product 0x7000" rev 1.10/1.00 addr 3 >> uhidev0 at uhub9 port 1 configuration 1 interface 0 "Microsoft >> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4 >> uhidev0: iclass 3/1 >> ukbd0 at uhidev0: 8 modifier keys, 6 key codes >> wskbd1 at ukbd0 mux 1 >> wskbd1: connecting to wsdisplay0 >> uhidev1 at uhub9 port 1 configuration 1 interface 1 "Microsoft >> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4 >> uhidev1: iclass 3/0, 1 report id >> uhid0 at uhidev1 reportid 1: input=7, output=0, feature=0 >> uhidev2 at uhub9 port 1 configuration 1 interface 2 "Microsoft >> Natural\M-. Ergonomic Keyboard 4000" rev 2.00/1.73 addr 4 >> uhidev2: iclass 3/1 >> ums0 at uhidev2: 5 buttons, Z dir >> wsmouse0 at ums0 mux 0 >> softraid0 at root >> root on sd0a swap on sd0b dump on sd0b >> uhub10 at uhub8 port 2 "D-Link product 0xf103" rev 2.00/1.00 addr 5
