J Sisson wrote:
Sorry, I meant your_last_post.[your configuration].
In other words, it'd help people make recommendations if we knew the
hardware you were running and what changes you'd made to the base system.
Here you are the output of dmesg
--------------------------------------------------------------------------------------------
# dmesg
OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD-K6(tm) 3D processor ("AuthenticAMD" 586-class) 361 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX
real mem = 267939840 (255MB)
avail mem = 250789888 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 07/21/99, BIOS32 rev. 0 @ 0xfb3c0,
SMBIOS rev. 2.2 @ 0xf0800 (32 entries)
bios0: vendor Award Software International, Inc. version "4.51 PG" date
07/21/99
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb848
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfddc0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 10 11 12
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371SB ISA" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x800 0xc9000/0x800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01
piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Conner Technology CT204>
wd0: 16-sector PIO, LBA, 4100MB, 8397686 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1 at pciide0 channel 1 drive 0: <ST320410A>
wd1: 16-sector PIO, LBA, 19092MB, 39102336 sectors
wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 10
piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x01: SMBus
disabled
xl0 at pci0 dev 9 function 0 "3Com 3c905C 100Base-TX" rev 0x74: irq 11,
address 00:04:79:67:c3:ec
bmtphy0 at xl0 phy 24: 3C905C internal PHY, rev. 6
xl1 at pci0 dev 11 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 10,
address 00:01:02:0a:60:2f
bmtphy1 at xl1 phy 24: 3C905C internal PHY, rev. 7
vga1 at pci0 dev 12 function 0 "S3 ViRGE" rev 0x06
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
isa0 at piixpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask f765 netmask ff65 ttymask ffff
mtrr: K6-family MTRR support (2 registers)
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
--------------------------------------------------------------------------------------------
...and what the "custom_options"?
Where can I find them?
--
Code cheap ($3 for an application)
