On Fri, Apr 17, 2009 at 12:02 AM, Denny White <denny...@cableone.net> wrote:
> On Thu, Apr 16, 2009 at 08:41:27PM -0500, Denny White spoke thusly:
>> Laptop is a Toshiba L305-S5921. I'm running -current on it with a snapshot
from 04/14/09. No, I couldn't wait for my new cd's
>> presently in route. ;) Mostly done just for learning purposes &
>> to see what I could get going on the new laptop which was given
>> to me as a present. I would've probably chosen a Lenovo if I'd
>> have had my choice, but I'm not going to turn down a free laptop.
>> Built GENERIC.MP which ran fine for me. When I do
>>
>> sysctl hw.sensors
>>
>> I get
>>
>> hw.sensors.acpiac0.indicator0=On (power supply)
>> hw.sensors.acpibat0.volt0=12.34 VDC (voltage)
>> hw.sensors.acpibat0.volt1=12.34 VDC (current voltage)
>> hw.sensors.acpibat0.amphour0=4.50 Ah (last full capacity)
>> hw.sensors.acpibat0.amphour1=0.00 Ah (warning capacity)
>> hw.sensors.acpibat0.amphour2=0.00 Ah (low capacity)
>> hw.sensors.acpibat0.amphour3=4.50 Ah (remaining capacity), OK
>> hw.sensors.acpibat0.raw0=0 (battery full), OK
>> hw.sensors.acpibat0.raw1=0 (rate)
>> hw.sensors.cpu0.temp0=45.00 degC
>>
>> which doesn't show cpu1. Next is the top portion of top's output
>> which does show both cpu's:
>>
>> load averages: 1.09, 1.02, 0.99 01:03:49
>> 22 processes: 21 idle, 1 on processor
>> CPU0 states: 3.7% user, 0.0% nice, 1.8% system, 0.3% interrupt, 94.2%
idle
>> CPU1 states: 4.0% user, 0.0% nice, 1.8% system, 0.0% interrupt, 94.2%
idle
>> Memory: Real: 7520K/349M act/tot Free: 2538M Swap: 0K/1028M used/tot
>>
>>
>> Here's dmesg which also shows both cpu's but fails on
>> acpitz0 at acpi0acpitz0: THRM: failed to read _TMP
>> which I thought might have something to do with the issue:
>>
>>
>> OpenBSD 4.5-current (GENERIC.MP) #1: Wed Apr 15 14:22:16 UTC 2009
>> r...@lapdaddy.cableone.net:/usr/src/sys/arch/i386/compile/GENERIC.MP
>> cpu0: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz ("GenuineIntel"
686-class) 2.17 GHz
>> cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
>> real mem = 3081773056 (2939MB)
>> avail mem = 2983903232 (2845MB)
>> mainbus0 at root
>> bios0 at mainbus0: AT/286+ BIOS, date 12/23/08, SMBIOS rev. 2.4 @ 0xe8120
(35 entries)
>> bios0: vendor INSYDE version "1.60" date 12/23/2008
>> bios0: TOSHIBA Satellite L305
>> acpi0 at bios0: rev 2
>> acpi0: tables DSDT FACP HPET APIC MCFG ASF! SLIC BOOT SSDT
>> acpi0: wakeup devices LID0(S4) P32_(S0) UHC1(S3) UHC2(S3) ECHI(S3) EXP1(S0)
EXP2(S0) EXP3(S4) EXP4(S4) EXP5(S4) EXP6(S4) AZAL(S4)
>> acpitimer0 at acpi0: 3579545 Hz, 24 bits
>> acpihpet0 at acpi0: 14318179 Hz
>> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>> cpu0 at mainbus0: apid 0 (boot processor)
>> cpu0: apic clock running at 166MHz
>> cpu1 at mainbus0: apid 1 (application processor)
>> cpu1: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz ("GenuineIntel"
686-class) 2.17 GHz
>> cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS
H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,TM2,CX16,xTPR
>> ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
>> ioapic0: misconfigured as apic 0, remapped to apid 4
>> acpiprt0 at acpi0: bus 0 (PCI0)
>> acpiprt1 at acpi0: bus 4 (P32_)
>> acpiprt2 at acpi0: bus 2 (EXP1)
>> acpiprt3 at acpi0: bus 3 (EXP2)
>> acpiprt4 at acpi0: bus -1 (EXP3)
>> acpiprt5 at acpi0: bus -1 (EXP4)
>> acpiprt6 at acpi0: bus 6 (EXP5)
>> acpiprt7 at acpi0: bus -1 (EXP6)
>> acpiprt8 at acpi0: bus -1 (PEGP)
>> acpiec0 at acpi0
>> acpicpu0 at acpi0
>> acpicpu1 at acpi0
>> acpitz0 at acpi0acpitz0: THRM: failed to read _TMP
>> : failed to read _TMP
>> acpibtn0 at acpi0: PWRB
>> acpibtn1 at acpi0: LID0
>> acpiac0 at acpi0: AC unit online
>> acpibat0 at acpi0: BAT0 model "PA3534U-1BRS" serial 7C3B type Li-ion
>> acpivideo at acpi0 not configured
>> acpivideo at acpi0 not configured
>> bios0: ROM list: 0xc0000/0xfa00! 0xd0000/0x1000 0xd1000/0x2c00!
>> cpu0: unknown Enhanced SpeedStep CPU, msr 0x060f0d2a06000d2a
>> cpu0: using only highest and lowest power states
>> cpu0: Enhanced SpeedStep 2167 MHz (1372 mV): speeds: 2167, 1000 MHz
>> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
>> pchb0 at pci0 dev 0 function 0 "Intel GM45 Host" rev 0x07
>> vga1 at pci0 dev 2 function 0 "Intel GM45 Video" rev 0x07
>> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
>> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
>> intagp0 at vga1
>> agp0 at intagp0: aperture at 0xc0000000, size 0x10000000
>> inteldrm0 at vga1: apic 4 int 16 (irq 11)
>> drm0 at inteldrm0
>> "Intel GM45 Video" rev 0x07 at pci0 dev 2 function 1 not configured
>> uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x03: apic 4 int 16
(irq 11)
>> uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x03: apic 4 int 21
(irq 10)
>> ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x03: apic 4 int 19
(irq 11)
>> ehci0: timed out waiting for BIOS
>> usb0 at ehci0: USB revision 2.0
>> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>> azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x03: apic 4
int 22 (irq 11)
>> azalia0: codecs: Realtek ALC268, AT&T/Lucent/0x1040, using Realtek ALC268
>> audio0 at azalia0
>> ppb0 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x03: apic 4 int 17
(irq 5)
>> pci1 at ppb0 bus 2
>> re0 at pci1 dev 0 function 0 "Realtek 8101E" rev 0x02: RTL8102E (0x3480),
apic 4 int 16 (irq 5), address 00:1e:33:9a:76:ee
>> rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1
>> ppb1 at pci0 dev 28 function 1 "Intel 82801I PCIE" rev 0x03: apic 4 int 16
(irq 11)
>> pci2 at ppb1 bus 3
>> ath0 at pci2 dev 0 function 0 "Atheros AR5424" rev 0x01: apic 4 int 17 (irq
11)
>> ath0: AR5424 14.2 phy 7.0 rf 0.0, WOR5_ETSIC, address 00:24:d2:01:89:ff
>> ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x03: apic 4 int 17
(irq 11)
>> pci3 at ppb2 bus 6
>> uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x03: apic 4 int 23
(irq 11)
>> uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x03: apic 4 int 19
(irq 11)
>> uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x03: apic 4 int 16
(irq 11)
>> uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x03: apic 4 int 18
(irq 11)
>> ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x03: apic 4 int 23
(irq 11)
>> ehci1: timed out waiting for BIOS
>> usb1 at ehci1: USB revision 2.0
>> uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
>> ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x93
>> pci4 at ppb3 bus 4
>> pcib0 at pci0 dev 31 function 0 vendor "Intel", unknown product 0x2919 rev
0x03
>> ahci0 at pci0 dev 31 function 2 "Intel 82801I AHCI" rev 0x03: apic 4 int 19
(irq 11), AHCI 1.2
>> ahci0: PHY offline on port 1
>> ahci0: PHY offline on port 4
>> scsibus0 at ahci0: 32 targets
>> sd0 at scsibus0 targ 0 lun 0: <ATA, ST9250827AS, 3.AA> SCSI3 0/direct
fixed
>> sd0: 238475MB, 512 bytes/sec, 488397168 sec total
>> cd0 at scsibus0 targ 5 lun 0: <MATSHITA, DVD-RAM UJ880AS, 1.50> ATAPI
5/cdrom removable
>> ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x03: apic 4 int
18 (irq 11)
>> iic0 at ichiic0
>> spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
>> spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5 SO-DIMM
>> usb2 at uhci0: USB revision 1.0
>> uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb3 at uhci1: USB revision 1.0
>> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb4 at uhci2: USB revision 1.0
>> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb5 at uhci3: USB revision 1.0
>> uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb6 at uhci4: USB revision 1.0
>> uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> usb7 at uhci5: USB revision 1.0
>> uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
>> isa0 at pcib0
>> isadma0 at isa0
>> pckbc0 at isa0 port 0x60/5
>> pckbd0 at pckbc0 (kbd slot)
>> pckbc0: using irq 1 for kbd slot
>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
>> pms0 at pckbc0 (aux slot)
>> pckbc0: using irq 12 for aux slot
>> wsmouse0 at pms0 mux 0
>> pcppi0 at isa0 port 0x61
>> midi0 at pcppi0: <PC speaker>
>> spkr0 at pcppi0
>> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
>> mtrr: Pentium Pro MTRR support
>> umass0 at uhub0 port 4 configuration 1 interface 0 "Generic USB2.0-CRW" rev
2.00/58.87 addr 2
>> umass0: using SCSI over Bulk-Only
>> scsibus1 at umass0: 2 targets, initiator 0
>> sd1 at scsibus1 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
removable
>> sd1: drive offline
>> uhidev0 at uhub4 port 1 configuration 1 interface 0 "vendor 0x15d9 USB
Mouse" rev 1.10/1.00 addr 2
>> uhidev0: iclass 3/1
>> ums0 at uhidev0: 3 buttons, Z dir
>> wsmouse1 at ums0 mux 0
>> softraid0 at root
>> root on sd0a swap on sd0b dump on sd0b
>> pckbc: command timeout
>> pms_disable: command error
>>
>>
>> Not being able to read cpu1 temp probably isn't a big deal, at
>> least I'm guessing it's not & that's it probably pretty close
>> to the same temp as cpu0 since they both seem to share the load
>> fairly equally when I'm doing intensive stuff like building a
>> kernel & so forth. I just wanted to try to learn how to enable
>> all functions on cpu1 if possible. Also, I thought it might help
>> if I included the advanced cmos settings:
>>
>>
>> Core Multi-Processing: [Enabled]
>> Dynamic CPU Frequency Mode: [Dynamic]
>> (other choice on above setting is 'Always Low')
>> Pointing Devices: [Disabled]
>> (above disables touchpad which I hate. using usb mouse instead)
>> Built-in LAN: [Enabled]
>> Wake-up on LAN: [Disabled]
>> Wake On Wireless LAN: [Disabled]
>> Critical Battery Wake-up: [Enabled]
>> Execute-Disable Bit Capability: [Enabled]
>> Intel Virtualization Technology: [Disabled]
>> Intel (R) Turbo Memory: [Enabled]
>> Legacy USB Support: [Enabled]
>> Wake on Keyboard: [Disabled]
>> Intel Dynamic Acceleration: [Disabled]
>> (not able to change above setting)
>> SATA Controller Mode: [AHCI]
>>
>> Any help, tips, reading links, etc., greatly appreciated.
>>
>>
>> Denny White
>>
>
> Okay, dumb-ass me. Sitting here looking at the screen it finally
> dawned on me I'm not looking at 2 physical cpu's, per se, but
> instead 2 built onto one chip. Gee, I wish I would've come up
> with that beforehand instead of opening my mouth and removing
> any doubt in regards to my hardware ignorance. Only thing in
> my defense is I've never owned anything like that before. Before
> getting this laptop given to me, my fastest box was an aging dell
> dimension Pentium IV 2.66. No dual-cores, no dual-cpu's. Time to
> slink off now. ;)
I'm sure there are other dumb-asses out there ( I just saw one in the
mirror a minute ago) . . . your post will come in handy for those
dumb-asses who actually check the archives.
>
>
> Denny White
>
> --
>
> ===============================================================
> () ASCII ribbon campaign - against html e-mail
> /\ www.asciiribbon.org - against proprietary attachments
> ===============================================================
> GnuPG key : 0x1644E79A | http://wwwkeys.nl.pgp.net
> Fingerprint: D0A9 AD44 1F10 E09E 0E67 EC25 CB44 F2E5 1644 E79A
> ===============================================================
>
>
--
www.nealhogan.net www.lambdaserver.com
