K.R. (Randy) Lewis,
We were able to confirm (today) that it is the /MP kernel that has the issue
defined below. The single CPU build ran the huge file copy just fine.
R
> Re-post in misc@ (sorry for posting wrongly before)
> -----------------
>
> Encountered the following: 4.3 i386 MP kernel w/Raidframe
> - throws a: splassert: uvm_map_p: want 1 have 1
>
> Here's what was going on.......
>
>
> We took a USB 250GB drive and wiped it (unallocated partition) using
> partition magic on one of those, what do you call it..
> ..oh yeah...WindowsXP thingys...(expedient, ok?)
>
> Then plugged it into a 4.3 OpenBSD MacMini, did a disklabel and
> established a partition sd0i of type MSDOS.
>
> Then did a newfs t msdos sd0i.
> All of this works great, each time we do it.
>
> Then mounted it on the MacMini 4.3 OpenBSD with no problems, so
> we were fairly sure it was OK.
>
> We unmounted it from the 4.3 OpenBSD MacMini and cruised on over to
> a Dell PowerEdge 1550 Dual-P3, 512MB with 2 QLogic Fibre channel boards
> with two arrays, all set up nicely with Raidframe - each array as RAID5 and
> both arrays mirrored as a RAID1. This configuration has been in use for
> quite some time and works quite well (although a recent disk
> replacement requires some attention..)
>
> We mounted the USB drive (configured as above) without issue.
>
> Kicked off a "cp /big_file_of_4GB to /usb_drive_mount_point" job
> and it ran for about an hour before issuing a kernal error...
>
> splassert: uvm_map_p: want 1 have 1
>
> ... to the console.
>
> The 'cp' was wedged, but the system seemed to be running.
>
> We were able to ssh into the system and look around, but issuing
> a 'reboot' from the ssh session caused the system to hang
> completely after the shutdown messages to the console - and
> somewhere in the 'syncing' before halt portion.
>
> So, before we go poking around in this MP system and perhaps
> retrace well worn steps ... has anyone seen this on an MP
> configuration (with or without Raidframe) ?
>
>
> Randy
>
> ------
>
> Here is the current DMESG, but please realize it's just now recovering
> from our 'force crash / reset' so there is some noise from the Raid stuff
> at the end.
>
> Also, note that the sd7 & sd8 disks are NOT part of any array.
> They are the boot / swap and /usr/src /usr/ports drives on this puppy.
>
> And, finally, this raidframe setup, with these disks have been
> working for over a year on a 4.1 version system. Just so you know.
>
> ----
> wally:randy {103} ssh [EMAIL PROTECTED]
> [EMAIL PROTECTED]'s password:
>
> Last login: Wed Jul 16 16:09:56 2008 from 10.1.0.170
> OpenBSD 4.3 (GENERIC.MP) #2: Tue Jul 1 13:45:45 EDT 2008
>
> Welcome to OpenBSD: The proactively secure Unix-like operating system.
>
> Please use the sendbug(1) utility to report bugs in the system.
> Before reporting a bug, please try to reproduce it with the latest
> version of the code. With bug reports, please try to ensure that
> enough information to reproduce the problem is enclosed, and if a
> known fix for it exists, include that as well.
>
> Terminal type? [vt220]
> # dmesg
> OpenBSD 4.3 (GENERIC.MP) #2: Tue Jul 1 13:45:45 EDT 2008
> [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
> cpu0: Intel Pentium III ("GenuineIntel" 686-class) 994 MHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
> real mem = 536379392 (511MB)
> avail mem = 510132224 (486MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/10/04, BIOS32 rev. 0 @ 0xffe90,
> SMBIOS rev. 2.3 @ 0xfb060 (55 entries)
> bios0: vendor Dell Computer Corporation version "A09" date 12/10/2004
> bios0: Dell Computer Corporation PowerEdge 1550/1000
> acpi0 at bios0: rev 0
> acpi0: tables DSDT FACP APIC
> acpi0: wakeup devices PCI0(S5) PCI2(S5)
> acpitimer0 at acpi0: 3579545 Hz, 32 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 1 (boot processor)
> cpu0: apic clock running at 132MHz
> cpu1 at mainbus0: apid 0 (application processor)
> cpu1: Intel Pentium III ("GenuineIntel" 686-class) 994 MHz
> cpu1:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 11, 16 pins
> ioapic0: misconfigured as apic 0, remapped to apid 2
> ioapic1 at mainbus0: apid 3 pa 0xfec01000, version 11, 16 pins
> ioapic1: misconfigured as apic 0, remapped to apid 3
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 1 (PCI1)
> acpiprt2 at acpi0: bus 2 (PCI2)
> acpicpu0 at acpi0
> acpicpu1 at acpi0
> bios0: ROM list: 0xc0000/0x8000 0xc8000/0x6000 0xce000/0x2800 0xd0800/0x800
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20HE Host" rev 0x23
> pci1 at pchb0 bus 1
> isp0 at pci1 dev 4 function 0 "QLogic ISP2100" rev 0x03: apic 3 int 9
> (irq 5)
> scsibus0 at isp0: 256 targets
> sd0 at scsibus0 targ 0 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd0: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd1 at scsibus0 targ 1 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd1: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd2 at scsibus0 targ 2 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd2: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd3 at scsibus0 targ 3 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd3: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd4 at scsibus0 targ 4 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd4: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd5 at scsibus0 targ 5 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd5: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd6 at scsibus0 targ 6 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd6: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20HE Host" rev 0x01
> pchb2 at pci0 dev 0 function 2 "ServerWorks CNB20HE Host" rev 0x01
> pchb3 at pci0 dev 0 function 3 "ServerWorks CNB20HE Host" rev 0x01
> pci2 at pchb3 bus 2
> ahc0 at pci2 dev 5 function 0 "Adaptec AIC-7899 U160" rev 0x01: apic 3
> int 11 (irq 3)
> scsibus1 at ahc0: 16 targets
> sd7 at scsibus1 targ 0 lun 0: <COMPAQ, BD0366349C, 3B02> SCSI2 0/direct
> fixed
> sd7: 34732MB, 14002 cyl, 20 head, 254 sec, 512 bytes/sec, 71132000 sec total
> sd8 at scsibus1 targ 1 lun 0: <SEAGATE, ST318451LC, 0003> SCSI3 0/direct
> fixed
> sd8: 17366MB, 10377 cyl, 10 head, 342 sec, 512 bytes/sec, 35566478 sec total
> safte0 at scsibus1 targ 6 lun 0: <DELL, 1x3 U2W SCSI BP, 1.21> SCSI2
> 3/processor fixed
> ahc1 at pci2 dev 5 function 1 "Adaptec AIC-7899 U160" rev 0x01: apic 3
> int 12 (irq 11)
> scsibus2 at ahc1: 16 targets
> isp1 at pci2 dev 6 function 0 "QLogic ISP2100" rev 0x03: apic 3 int 13
> (irq 10)
> scsibus3 at isp1: 256 targets
> sd9 at scsibus3 targ 0 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd9: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd10 at scsibus3 targ 1 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd10: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd11 at scsibus3 targ 2 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd11: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd12 at scsibus3 targ 3 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd12: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd13 at scsibus3 targ 4 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd13: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd14 at scsibus3 targ 5 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd14: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> sd15 at scsibus3 targ 6 lun 0: <CSC 36GB, 15K REFURBISHED, 0026> SCSI3
> 0/direct fixed
> sd15: 35003MB, 50824 cyl, 2 head, 705 sec, 512 bytes/sec, 71687372 sec total
> fxp0 at pci0 dev 1 function 0 "Intel 8255x" rev 0x08, i82559: apic 3 int
> 0 (irq 11), address 00:b0:d0:f3:6f:de
> inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
> fxp1 at pci0 dev 2 function 0 "Intel 8255x" rev 0x08, i82559: apic 3 int
> 1 (irq 10), address 00:b0:d0:f3:6f:df
> inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
> vga1 at pci0 dev 3 function 0 "ATI Rage XL" rev 0x27
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> piixpm0 at pci0 dev 15 function 0 "ServerWorks OSB4" rev 0x50: SMI
> iic0 at piixpm0
> admtemp0 at iic0 addr 0x18: max1617
> lmenv0 at iic0 addr 0x2c: lm81 rev 3
> lmenv1 at iic0 addr 0x2d: lm81 rev 3
> lmenv2 at iic0 addr 0x2e: lm81 rev 3
> maxtmp0 at iic0 addr 0x4c: max6657
> lmtemp0 at iic0 addr 0x4d: lm75
> iic0: addr 0x4e 00=d0 01=d0 02=d0 03=d0 04=d0 05=d0 06=d0 07=d0 08=d0
> words 00=0000 01=0000 02=0000 03=0000 04=0000 05=0000 06=0000 07=0000
> 08=0000 09=0000 0a=0000 0b=0000 0c=0000 0d=0000 0e=0000 0f=0000
> spdmem0 at iic0 addr 0x50: unknown memory type 208
> spdmem1 at iic0 addr 0x51: unknown memory type 208
> spdmem2 at iic0 addr 0x52: unknown memory type 208
> spdmem3 at iic0 addr 0x53: unknown memory type 208
> spdmem4 at iic0 addr 0x54: unknown memory type 208
> spdmem5 at iic0 addr 0x55: unknown memory type 208
> spdmem6 at iic0 addr 0x56: unknown memory type 208
> spdmem7 at iic0 addr 0x57: unknown memory type 208
> pciide0 at pci0 dev 15 function 1 "ServerWorks OSB4 IDE" rev 0x00: DMA
> atapiscsi0 at pciide0 channel 0 drive 0
> scsibus4 at atapiscsi0: 2 targets
> cd0 at scsibus4 targ 0 lun 0: <SAMSUNG, CD-ROM SN-124, S003> SCSI0
> 5/cdrom removable
> cd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
> ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x04:
> apic 2 int 7 (irq 7), version 1.0, legacy support
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0 "ServerWorks OHCI root hub" rev 1.00/1.00 addr 1
> isa0 at mainbus0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> mtrr: Pentium Pro MTRR support
> Kernelized RAIDframe activated
> softraid0 at root
> ahc0: target 0 using 16bit transfers
> ahc0: target 0 synchronous at 80.0MHz DT, offset = 0x3f
> ahc0: target 1 using 16bit transfers
> ahc0: target 1 synchronous at 80.0MHz DT, offset = 0x3f
> root on sd7a swap on sd7b dump on sd7b
> WARNING: / was not properly unmounted
> raid0: Component /dev/sd0a being configured at row: 0 col: 0
> Row: 0 Column: 0 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd0a is not clean !
> raid0: Component /dev/sd1a being configured at row: 0 col: 1
> Row: 0 Column: 1 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd1a is not clean !
> raid0: Component /dev/sd2a being configured at row: 0 col: 2
> Row: 0 Column: 2 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd2a is not clean !
> raid0: Component /dev/sd3a being configured at row: 0 col: 3
> Row: 0 Column: 3 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd3a is not clean !
> raid0: Component /dev/sd4a being configured at row: 0 col: 4
> Row: 0 Column: 4 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd4a is not clean !
> raid0: Component /dev/sd5a being configured at row: 0 col: 5
> Row: 0 Column: 5 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd5a is not clean !
> raid0: Component /dev/sd6a being configured at row: 0 col: 6
> Row: 0 Column: 6 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 238
> Clean: No Status: 0
> /dev/sd6a is not clean !
> raid0 at rootraid1: Component /dev/sd9a being configured at row: 0 col: 0
> Row: 0 Column: 0 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd9a is not clean !
> raid1: Component /dev/sd10a being configured at row: 0 col: 1
> Row: 0 Column: 1 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd10a is not clean !
> raid1: Component /dev/sd11a being configured at row: 0 col: 2
> Row: 0 Column: 2 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd11a is not clean !
> raid1: Component /dev/sd12a being configured at row: 0 col: 3
> Row: 0 Column: 3 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd12a is not clean !
> raid1: Component /dev/sd13a being configured at row: 0 col: 4
> Row: 0 Column: 4 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd13a is not clean !
> raid1: Component /dev/sd14a being configured at row: 0 col: 5
> Row: 0 Column: 5 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd14a is not clean !
> raid1: Component /dev/sd15a being configured at row: 0 col: 6
> Row: 0 Column: 6 Num Rows: 1 Num Columns: 7
> Version: 2 Serial Number: 1234 Mod Counter: 188
> Clean: No Status: 0
> /dev/sd15a is not clean !
> raid1 at rootHosed component: /dev/raid1a.
> Hosed component: /dev/raid1a.
> raid2: Component /dev/raid0a being configured at row: 0 col: 0
> Row: 0 Column: 0 Num Rows: 1 Num Columns: 2
> Version: 2 Serial Number: 1234 Mod Counter: 321
> Clean: No Status: 0
> /dev/raid0a is not clean !
> raid2: Ignoring /dev/raid1a.
> raid2 at rootraid2: Error re-writing parity!
>
> [demime 1.01d removed an attachment of type APPLICATION/DEFANGED which had a
> name of randy.7484DEFANGED-vcf]
>
>
>
--
[demime 1.01d removed an attachment of type APPLICATION/DEFANGED which had a
name of randy.9118DEFANGED-vcf]
