On Jan 12, 2008 10:44 PM, Limaunion <[EMAIL PROTECTED]> wrote:
> OpenBSD 4.2 (GENERIC) #375: Tue Aug 28 10:38:44 MDT 2007
Also note that you are using a kernel that is over four months old and
it obviously does not yet contain the extensions that were added to
glxpcib(4) to support the hardware timer for watchdogd, and the GPIO
pins (see gpioctl(8) to control the LEDs, for example) , or security
block acceleration glxsb(4).
So maybe you want to upgrade the system on your CF card to the
-current snapshot to be able to use these features.
For reference, here is the dmesg of my ALIX that runs the latest snapshot:
OpenBSD 4.2-current (GENERIC) #647: Fri Jan 11 02:06:06 MST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD"
586-class) 499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 268009472 (255MB)
avail mem = 251240448 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/10/07, BIOS32 rev. 0 @ 0xfceb2
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00:0d:b9:12:6c:10
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:0d:b9:12:6c:11
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12,
address 00:0d:b9:12:6c:12
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
ral0 at pci0 dev 12 function 0 "Ralink RT2561" rev 0x00: irq 9,
address 00:08:a1:9c:32:c4
ral0: MAC/BBP RT2661B, RF RT2527
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 0,
32-bit 3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-1024>
wd0: 4-sector PIO, LBA, 977MB, 2001888 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15,
version 1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e1ef netmask ffef ttymask ffef
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
