The serial console works correctly when the speed is set to 9600 bps.
On Thu, 2008-01-03 at 12:42 -0700, Bobby Johnson wrote: > I'm missing the bootloader interaction with OpenBSD 4.2 installed on a > compact flash card in this alix2c3. With the most recent bios from PC > Engines 0.99. If I strike any keys ( like boot -s) during the time when > the boot> prompt should appear the system will not boot. If I wait it > boots fine. The output from a console session is below. When this same > compact flash is installed in a PC Engines wrap board I get the boot> > prompt. > > > PC Engines ALIX.2 v0.99 > 640 KB Base Memory > 261120 KB Extended Memory > > 01F0 Master 044A TRANSCEND > Phys C/H/S 993/16/63 Log C/H/S 993/16/63 > Using drive 0, partition 3; > Loading;... > probing: pc0 com0 pci mem[640K 255M a20=on] > disk: hd0 > >> OpenBSD/i386 BOOT 3.01 > - > com0: 38400 baud > switching console to com0 > > *** some extended ascii characters I appearently can't paste here *** > > [ using 563904 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. > Copyright (c) 1995-2007 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 4.2 (GENERIC) #375: Tue Aug 28 10:38:44 MDT 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > RTC BIOS diagnostic error 80<clock_battery> > cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" > 586-class) 499 MHz > cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX > real mem = 268009472 (255MB) > avail mem = 251506688 (239MB) > RTC BIOS diagnostic error 80<clock_battery> > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 12/10/07, BIOS32 rev. 0 @ 0xfceb2 > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #0 is the last bus > bios0: ROM list: 0xe0000/0xa800 > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31 > glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES > vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10, > address 00:0d:b9:12:6e:e4 > ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, > address 00:0d:b9:12:6e:e5 > ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, > address 00:0d:b9:12:6e:e6 > ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > pcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03 > pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <TRANSCEND> > wd0: 1-sector PIO, LBA, 488MB, 1000944 sectors > wd0(pciide0:0:0): using PIO mode 4 > pciide0: channel 1 ignored (disabled) > ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15, > version 1.0, legacy support > ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0: AMD EHCI root hub, rev 2.00/1.00, addr 1 > isa0 at pcib0 > isadma0 at isa0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pccom0: console > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1: AMD OHCI root hub, rev 1.00/1.00, addr 1 > biomask e3ef netmask ffef ttymask ffef > pctr: user-level cycle counter enabled > mtrr: K6-family MTRR support (2 registers) > nvram: invalid checksum > dkcsum: wd0 matches BIOS drive 0x80 > root on wd0a swap on wd0b dump on wd0b > clock: unknown CMOS layout > WARNING: clock time much less than file system time > WARNING: using file system time > WARNING: CHECK AND RESET THE DATE! > Automatic boot in progress: starting file system checks. > /dev/rwd0a: file system is clean; not checking > /dev/rwd0e: file system is clean; not checking > /dev/rwd0d: file system is clean; not checking > pax: /var/./cron/tabs/.sock skipped. Sockets cannot be copied or > extracted > pax: /var/./empty/dev/log skipped. Sockets cannot be copied or extracted > mount_mfs: reduced number of fragments per cylinder group from 368 to > 352 to enlarge last cylinder group > setting tty flags > pf enabled > starting network > starting system logger > starting initial daemons: ntpd. > savecore: no core dump > checking quotas: done. > building ps databases: kvm dev. > clearing /tmp > starting pre-securelevel daemons:. > setting kernel security level: kern.securelevel: 0 -> 1 > creating runtime link editor directory cache. > preserving editor files > starting network daemons: sendmail ftp-proxy inetd sshd. > starting local daemons:. > standard daemons: cron. > Wed Jan 2 15:54:41 MST 2008 > > OpenBSD/i386 (firewall.icdnt.local) (tty00) > > login:
