Umaxx wrote: > hi, > > after upgrading my router to -current the dsl pppoe connection does not work > anymore. > userland ppp connects fine but freezes after K 30 seconds. freeze means the > connection is still there no errors shown in logs and ifconfig state is normal > but there is no more incoming traffic. the provider and modem hardware is ok > since i'm connected now through a netscreen to write this mail. i changed > nothing > in ppp configuration since years and disabled pf for testing... same problem. > as i can see in source changes: not much has changed in userland ppp and nfe > code > since 4.1.
I would suggest you try with a different ethernet card if possible just to rule out that possibility. Have you checked your cables? You can also try to experiment with media settings (speed/duplex) of your card. > i read in some forums that it would be better to user kernel pppoe... > so i tried to use kernel pppoe as workaround, but its does not connect. i used > following configuration in /etc/hostname.pppoe0: > > inet 0.0.0.0 255.255.255.255 0.0.0.1 pppoedev nfe1 \ > authproto pap authname **** authkey **** up > !/sbin/route add default 0.0.0.1 Please read pppoe(4) for -current, you need to add "-ifp pppoe0" in -current to your route command. First test using a kernel from the latest snapshot. With and without MP. This will make sure we are testing/debugging the same thing. If your problem persists, please send me the debug outputs from /var/log/messages after "ifconfig pppoe0 debug" and the binary tcpdump of a session: tcpdump -w pppoe.dump -i nfe1 not ip Thanks Can > and of course: "up" in /etc/hostname.nfe1 > > if i enable debug i see a lot of outgoing packages... and then a timeout after > a > while. reconnect and again the same... > it stays in the sppp phase of "establish connection using pap authname ****" > > I'm located in germany using arcor as provider. > anyone else using dsl pppoe (kernel/userland) in current or latest snapshots - > maybe in germany with arcor? > > any hints are really welcome. > dmesg follows.... > > regards, > > joerg > > OpenBSD 4.2 (GENERIC.MP) #0: Wed Aug 8 17:31:49 CEST 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/GENERIC.MP > real mem = 2145972224 (2046MB) > avail mem = 2072682496 (1976MB) > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xf0000 (78 entries) > bios0: vendor Phoenix Technologies, LTD version "ASUS M2N32-SLI DELUXE ACPI > BIOS > Revision 0603" date 06/27/2006 > bios0: ASUSTeK Computer INC. M2N32-SLI DELUXE > acpi0 at mainbus0: rev 0 > acpi0: tables DSDT FACP SSDT MCFG APIC > acpitimer at acpi0 not configured > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+, 2411.34 MHz > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line > 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu0: apic clock running at 200MHz > cpu1 at mainbus0: apid 1 (application processor) > cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+, 2410.98 MHz > cpu1: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS > H,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line > 16-way L2 cache > cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative > cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative > ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 11, 24 pins > ioapic0: misconfigured as apic 0, remapped to apid 2 > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 5 (HUB0) > acpicpu at acpi0 not configured > acpicpu at acpi0 not configured > acpitz at acpi0 not configured > acpibtn at acpi0 not configured > cpu0: PowerNow! K8 2410 MHz: speeds: 2400 2200 2000 1800 1000 MHz > pci0 at mainbus0 bus 0: configuration mode 1 > "NVIDIA C51 Host" rev 0xa2 at pci0 dev 0 function 0 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 1 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 2 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 3 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 4 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 5 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 6 not configured > "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 7 not configured > ppb0 at pci0 dev 3 function 0 "NVIDIA C51 PCIE" rev 0xa1 > pci1 at ppb0 bus 1 > ppb1 at pci0 dev 4 function 0 "NVIDIA C51 PCIE" rev 0xa1 > pci2 at ppb1 bus 2 > ppb2 at pci2 dev 0 function 0 "Intel IOP332 PCIE-PCIX" rev 0x07 > pci3 at ppb2 bus 3 > arc0 at pci3 dev 14 function 0 "Areca ARC-1210" rev 0x00: apic 2 int 11 (irq > 11) > arc0: 4 SATA Ports, 256MB SDRAM, FW Version: V1.42 2006-10-13 > scsibus0 at arc0: 16 targets > sd0 at scsibus0 targ 0 lun 0: <Areca, ARC-1210-VOL#00, R001> SCSI3 0/direct > fixed > sd0: 476837MB, 56514 cyl, 36 head, 480 sec, 512 bytes/sec, 976562176 sec total > ppb3 at pci2 dev 0 function 2 "Intel IOP332 PCIE-PCIX" rev 0x07 > pci4 at ppb3 bus 4 > "NVIDIA MCP55 Memory" rev 0xa1 at pci0 dev 8 function 0 not configured > pcib0 at pci0 dev 9 function 0 "NVIDIA MCP55 ISA" rev 0xa2 > nviic0 at pci0 dev 9 function 1 "NVIDIA MCP55 SMBus" rev 0xa2 > iic0 at nviic0 > adt0 at iic0 addr 0x2e: adt7475 rev 0x69 > iic1 at nviic0 > iic1: addr 0x18 00=f0 01=00 02=00 03=f0 04=00 05=00 06=00 07=00 08=00 09=10 > 10=08 > 11=00 12=00 13=0a 14=00 15=00 16=00 17=34 20=95 21=92 22=00 32=00 > "NVIDIA MCP55 Memory" rev 0xa2 at pci0 dev 9 function 2 not configured > ohci0 at pci0 dev 10 function 0 "NVIDIA MCP55 USB" rev 0xa1: apic 2 int 7 (irq > 7), version 1.0, legacy support > ehci0 at pci0 dev 10 function 1 "NVIDIA MCP55 USB" rev 0xa2: apic 2 int 10 > (irq 10) > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0: NVIDIA EHCI root hub, rev 2.00/1.00, addr 1 > pciide0 at pci0 dev 12 function 0 "NVIDIA MCP55 IDE" rev 0xa1: DMA, channel 0 > configured to compatibility, channel 1 configured to compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus1 at atapiscsi0: 2 targets > cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-H12N, UL01> SCSI0 5/cdrom > removable > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 > pciide0: channel 1 ignored (disabled) > pciide1 at pci0 dev 13 function 0 "NVIDIA MCP55 SATA" rev 0xa2: DMA > pciide1: using apic 2 int 5 (irq 5) for native-PCI interrupt > pciide2 at pci0 dev 13 function 1 "NVIDIA MCP55 SATA" rev 0xa2: DMA > pciide2: using apic 2 int 5 (irq 5) for native-PCI interrupt > pciide3 at pci0 dev 13 function 2 "NVIDIA MCP55 SATA" rev 0xa2: DMA > pciide3: using apic 2 int 5 (irq 5) for native-PCI interrupt > ppb4 at pci0 dev 14 function 0 "NVIDIA MCP55 PCI-PCI" rev 0xa2 > pci5 at ppb4 bus 5 > wi0 at pci5 dev 7 function 0 "Intersil PRISM2.5" rev 0x01: apic 2 int 10 (irq > 10) > wi0: PRISM2.5 ISL3874A(Mini-PCI) (0x8013), Firmware 1.0.7 (primary), 1.3.6 > (station), address 00:09:5b:2f:6b:8d > "TI TSB43AB22 FireWire" rev 0x00 at pci5 dev 11 function 0 not configured > azalia0 at pci0 dev 14 function 1 "NVIDIA MCP55 HD Audio" rev 0xa2: apic 2 int > 11 > (irq 11) > azalia0: host: High Definition Audio rev. 1.0 > azalia0: codec: Analog Devices/0x198b (rev. 2.0), HDA version 1.0 > audio0 at azalia0 > nfe0 at pci0 dev 16 function 0 "NVIDIA MCP55 LAN" rev 0xa2: apic 2 int 5 (irq > 5), > address 00:18:f3:49:aa:86 > eephy0 at nfe0 phy 1: Marvell 88E1116 Gigabit PHY, rev. 1 > nfe1 at pci0 dev 17 function 0 "NVIDIA MCP55 LAN" rev 0xa2: apic 2 int 10 (irq > 10), address 00:18:f3:49:ad:96 > eephy1 at nfe1 phy 1: Marvell 88E1116 Gigabit PHY, rev. 1 > ppb5 at pci0 dev 18 function 0 "NVIDIA MCP55 PCIE" rev 0xa2 > pci6 at ppb5 bus 6 > ppb6 at pci0 dev 20 function 0 "NVIDIA MCP55 PCIE" rev 0xa2 > pci7 at ppb6 bus 7 > ppb7 at pci0 dev 22 function 0 "NVIDIA MCP55 PCIE" rev 0xa2 > pci8 at ppb7 bus 8 > sili0 at pci8 dev 0 function 0 "CMD Technology SiI3132 SATA" rev 0x01: apic 2 > int > 11 (irq 11) > scsibus2 at sili0: 2 targets > ppb8 at pci0 dev 23 function 0 "NVIDIA MCP55 PCIE" rev 0xa2 > pci9 at ppb8 bus 9 > vga1 at pci9 dev 0 function 0 "NVIDIA GeForce 7600 GT" rev 0xa1 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00 > pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00 > pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00 > pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00 > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > intr_establish: pic ioapic0 pin 7: can't share type 3 with 2 > it0 at isa0 port 0x290/8: IT87 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1: NVIDIA OHCI root hub, rev 1.00/1.00, addr 1 > ugen0 at uhub0 port 9 > ugen0: Realtek RTL8187, rev 2.00/1.00, addr 2 > uts0 at uhub1 port 7 configuration 1 interface 0 > uts0: eGalax Touch Panel, rev 1.10/1.00, addr 2 > wsmouse0 at uts0 mux 0 > ugen1 at uhub1 port 8 > ugen1: MConsult IRTrans USB, rev 1.10/4.00, addr 3 > dkcsum: sd0 matches BIOS drive 0x80 > root on sd0a swap on sd0b dump on sd0b
