3rd install finished, booted up with no problem.
Added SATA card back in, booted up with no problem.
Connected SATA hard drive, get many problems with various mounts being busy
Here is some hand copied console output with a SATA drive connected during boot:
/dev/rwd0d: MARKING FILE SYSTEM CLEAN
/dev/rwd0e: MARKING FILE SYSTEM CLEAN
mount_ffs: /dev/wd0a on /: Invalid argument
mount_ffs: /dev/wd1a on /usr: Device busy
mount_ffs: /dev/wd0a on /: Invalid argument
setting tty flags
machdep.allowaperture: 0->2
startnetwork
override rw-r--r-- root/wheel for /etc/resolv.conf?
I stopped it there.
dmesg is below: The SATA card shows up as pciide0
This is with SATA card, but no SATA drive
OpenBSD 4.1 (GENERIC) #1435: Sat Mar 10 19:07:45 MST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 CPU 2.80GHz ("GenuineIntel" 686-class) 2.80 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,CNXT-ID,xTPR
real mem = 1071693824 (1046576K)
avail mem = 970477568 (947732K)
using 4278 buffers containing 53706752 bytes (52448K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 12/02/03, BIOS32 rev. 0 @
0xffe90, SMBIOS rev. 2.3 @ 0xf0450 (60 entries)
bios0: Dell Computer Corporation Dimension 2400
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfeae0/144 (7 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801DB LPC" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xb800 0xcb800/0x1800! 0xcd000/0x3000
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845G/GL" rev 0x01
vga1 at pci0 dev 2 function 0 "Intel 82845G/GL Video" rev 0x01:
aperture at 0xe8000000, size 0x8000000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 5
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0x81
pci1 at ppb0 bus 1
pciide0 at pci1 dev 5 function 0 "CMD Technology SiI3512 SATA" rev 0x01: DMA
pciide0: using irq 3 for native-PCI interrupt
bce0 at pci1 dev 9 function 0 "Broadcom BCM4401" rev 0x01: irq 3,
address 00:0f:1f:58:03:2b
bmtphy0 at bce0 phy 1: BCM4401 10/100baseTX PHY, rev. 0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801DB LPC" rev 0x01
pciide1 at pci0 dev 31 function 1 "Intel 82801DB IDE" rev 0x01: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide1 channel 0 drive 0: <WDC WD400BB-75FJA1>
wd0: 16-sector PIO, LBA, 38146MB, 78125000 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide1 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <LITE-ON, COMBO SOHC-5236V, R$0K> SCSI0
5/cdrom removable
wd1 at pciide1 channel 1 drive 1: <WDC WD300BB-75DEA0>
wd1: 16-sector PIO, LBA, 28610MB, 58593750 sectors
cd0(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 2
wd1(pciide1:1:1): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x01: irq 3
iic0 at ichiic0
auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 3, ICH4 AC97
ac97: codec id 0x41445374 (Analog Devices AD1981B)
ac97: codec features headphone, 20 bit DAC, No 3D Stereo
audio0 at auich0
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask ef6d netmask ef6d ttymask ffef
pctr: user-level cycle counter enabled
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
On 6/18/07, Bruce Bauer <[EMAIL PROTECTED]> wrote:
> I'm doing some server remixes.
> Installing OpenBSD 4.1 on this one Dell box for 3rd time.
> 1st time no problem, but had a suspected application issue with AMANDA.
> So installed Fedora Core 6. no problem, but needed more disk space.
> Added SATA controller and disk. Had stability issues so upgraded to
> Fedora 7 and AMANDA puked.
> Installed OpenBSD 4.1 2nd time. No problems during install. 3 drives
> recognized and formatted. wd0 and wd1 are IDE and wd2 is SATA.
> Received congratulations message on successful install, typed in halt,
> removed CD and rebooted.
> Using disk 0, partition 3
> No OS
>
> Went to the FAQ and
> fdisk -u wd0
> no change
> and
> mount /dev/wd0a /mnt
> /usr/mdec/installboot -v /mnt/boot /usr/mdec/biosboot wd0
> still no change
>
> I have removed the SATA card and am installing OpenBSD 4.1 3rd time.
> I will try putting the SATA card back in after getting a running system.
> When this install is finished I will have a Dmesg available.
