It took me a while to get to this, and I'm just starting to investigate,
but I figured I'd give an update. Based on Stefan's comments, I wasn't
expecting things to work, but I figured I'd post what I have so far.
The behavior seems to be consistent between the 18 Nov and 24 Nov
snapshots; the dmesg for the latter is at the end of this post, as
well as the output of `ifconfig -a` and `pcidump -v 2>&1`; for the
latter, note the PCIOCGETVPD that shows up when dumping 0:29:1.
Summary: Two dwqe devices show, but the behavior is inconsistent.
The first bit on Observations describes some of the inconsistency in
case it provides anyone with some insight. After that, there's a short
discussion section, followed by pcidump and dmesg outputs.
Note that em0 is configured throughout (I'm mostly connecting via
ssh while watching console). Changes are made on dwqe only. The
cabling to the dwqe ports was validated by observing
link status and media changes when the cabling was attached to em1.
=== Observations:
Once running snapshots, I initially configured the network for dwqe0.
It came up and I was able to ping hosts on the dwqe0 network, but
I noticed that carrier state seemed unpredictable. I then deleted
hostname.dwqe0 and started trying to determine behavior based only on
ifconfig status and media values. In short, things seem to be
quite unpredicable. Some sample trials are shown, below:
Trial 1: When neither dwqe device is configured, but dwqe0 is
plugged into a switch at boot (all expected behavior):
a. Initially status on dwqe0 is "active", dwqe1 is "no carrier".
b. Unplugging the cable results in both being "no carrier".
c. Plugging into dwqe1 changes dwqe1 to "active"
d. Changing cable to dwqe0 results in dwqe0 "active", and
dwqe1 as "no carrier".
Trial 2: When neither dwqe device is configured, and neither device is
plugged into a switch:
a. Initially at boot the carrier LEDs are dark (as expected).
b. ifconfig does not report a status line at all (media shows
as autoselect/none)
c. Plugging dwqe0 into the switch fails to result in a change
of status or media values, the link light doesn't show
d. Switching the cable from dwqe0 to dwqe1 exhibits the same
behavior as (c)
Trial 3: Similar sequence as Trial 1, except this time:
a. The link light of dwqe0 comes on at boot
b. Neither dwqe status value is shown, media is autoselect/none,
similar to Trial 2
c. The link light stays on when dwqe0 is unplugged.
Trial 4: Following trial 3, do a shutdown and manual power-off
(but leave the power connector attached):
a. The link light of dwqe0 stays on while the device is powered
down, even if the cable is detached
b. Detaching power caused the link light to go off. Waiting 20s
and reapplying power resulted in the no-link-light case of
Trial 2, other than the fact that the cable was still connected.
Trial 5: I actually saw this one early on, when hostname.dwqe0 was
configured, and dwqe0 was plugged in during boot:
a. Network connection is alive as configured.
b. Detatching the cable causes dwqe0 to go "no carrier"
c. Reattaching the cable does NOT return the status to "active".
This seems to be intermittent.
Trial 6: I'm pretty sure I also saw a case where the cable was
plugged into dwqe0 after boot, the link light was initially off,
but eventually lit after a few _minutes_. I wasn't recording enough
detail at that point to be sure, though.
=== Discussion
I'm just starting to wrap my head around the network device driver code.
I've read the EuroBSDCon 2017 paper, and am going through the various
*dwqe* files in CVS, as well as pcidevs*. Other hints are welcome.
Stefan mentioned up-thread:
> At present we are only attaching dwqe to one of several possible MAC
> PCI IDs
I'm assuming this is referring to dwqe_pci_attach, which would imply
that the attach _does_ occur already since dmesg shows the two
Elkhart Lake Ethernets?
=== ifconfig -a (trimmed, dwqe0 currently connected to switch)
dwqe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 84:8b:cd:4d:b5:f6
index 3 priority 0 llprio 3
media: Ethernet autoselect (none)
dwqe1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
lladdr 84:8b:cd:4d:bc:36
index 4 priority 0 llprio 3
media: Ethernet autoselect (none)
=== pcidump -v
Domain /dev/pci0:
0:0:0: Intel Elkhart Lake Host
0x0000: Vendor ID: 8086, Product ID: 453a
0x0004: Command: 0006, Status: 2090
0x0008: Class: 06 Bridge, Subclass: 00 Host,
Interface: 00, Revision: 01
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 00 Line: 00 Min Gnt: 00 Max Lat: 00
0x00e0: Capability 0x09: Vendor Specific
0:2:0: Intel UHD Graphics
0x0000: Vendor ID: 8086, Product ID: 4571
0x0004: Command: 0007, Status: 0010
0x0008: Class: 03 Display, Subclass: 00 VGA,
Interface: 00, Revision: 01
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000081000000/0x01000000
0x0018: BAR mem prefetchable 64bit addr: 0x0000000070000000/0x10000000
0x0020: BAR io addr: 0x00005000/0x0040
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0040: Capability 0x09: Vendor Specific
0x0070: Capability 0x10: PCI Express
Max Payload Size: 128 / 128 bytes
Max Read Request Size: 128 bytes
0x0100: Enhanced Capability 0x1b: Process Address Space ID
0x0200: Enhanced Capability 0x0f: Address Translation Services
0x0300: Enhanced Capability 0x13: Page Request Interface
0x00ac: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x00d0: Capability 0x01: Power Management
State: D0
0:8:0: Intel Elkhart Lake GNA
0x0000: Vendor ID: 8086, Product ID: 4511
0x0004: Command: 0006, Status: 0010
0x0008: Class: 08 System, Subclass: 80 Miscellaneous,
Interface: 00, Revision: 01
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a0000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0090: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x00a0: Capability 0x09: Vendor Specific
0x00dc: Capability 0x01: Power Management
State: D0
0x00f0: Capability 0x13: PCI Advanced Features
0:16:0: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b44
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a9000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:16:1: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b45
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834ab000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 02 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:20:0: Intel Elkhart Lake xHCI
0x0000: Vendor ID: 8086, Product ID: 4b7d
0x0004: Command: 0006, Status: 0290
0x0008: Class: 0c Serial Bus, Subclass: 03 USB,
Interface: 30, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x0000000083480000/0x00010000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0070: Capability 0x01: Power Management
State: D0
0x0080: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0090: Capability 0x09: Vendor Specific
0x00b0: Capability 0x09: Vendor Specific
0:20:2: Intel Elkhart Lake SRAM
0x0000: Vendor ID: 8086, Product ID: 4b7f
0x0004: Command: 0006, Status: 0010
0x0008: Class: 05 Memory, Subclass: 00 RAM,
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083490000/0x00004000
0x0018: BAR mem 64bit addr: 0x00000000834a3000/0x00001000
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 00 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0:21:0: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b78
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a1000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:21:1: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b79
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a2000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 02 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:21:2: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b7a
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a4000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 03 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:21:3: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b7b
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a5000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 04 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:22:0: Intel Elkhart Lake HECI
0x0000: Vendor ID: 8086, Product ID: 4b70
0x0004: Command: 0000, Status: 0010
0x0008: Class: 07 Communications, Subclass: 80 Miscellaneous,
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x00000000834a8000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0050: Capability 0x01: Power Management
State: D0
0x008c: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0x00a4: Capability 0x09: Vendor Specific
0:23:0: Intel Elkhart Lake AHCI
0x0000: Vendor ID: 8086, Product ID: 4b63
0x0004: Command: 0007, Status: 02b0
0x0008: Class: 01 Mass Storage, Subclass: 06 SATA,
Interface: 01, Revision: 11
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 32bit addr: 0x8349e000/0x00002000
0x0014: BAR mem 32bit addr: 0x834ad000/0x00000100
0x0018: BAR io addr: 0x00005080/0x0008
0x001c: BAR io addr: 0x00005088/0x0004
0x0020: BAR io addr: 0x00005060/0x0020
0x0024: BAR mem 32bit addr: 0x834ac000/0x00000800
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0070: Capability 0x01: Power Management
State: D0
0x00a8: Capability 0x12: SATA
0:25:0: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4b4b
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x00000000834a6000/0x00001000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0:27:0: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4bb9
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083498000/0x00002000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0:27:1: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4bba
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 01, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x000000008349a000/0x00002000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 02 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0:27:6: Intel Elkhart Lake I2C
0x0000: Vendor ID: 8086, Product ID: 4bbf
0x0004: Command: 0006, Status: 0010
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 06, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x000000008349c000/0x00002000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 03 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0:28:0: Intel Elkhart Lake PCIE
0x0000: Vendor ID: 8086, Product ID: 4b3c
0x0004: Command: 0007, Status: 0010
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 81, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 5,
Secondary Latency Timer: 00
0x001c: I/O Base: 30, I/O Limit: 40, Secondary Status: 2000
0x0020: Memory Base: 8200, Memory Limit: 82f0
0x0024: Prefetch Memory Base: 8001, Prefetch Memory Limit: 80f1
0x0028: Prefetch Memory Base Upper 32 Bits: 00000000
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: 0000, I/O Limit Upper 16 Bits: 0000
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000
0x0040: Capability 0x10: PCI Express
Max Payload Size: 128 / 128 bytes
Max Read Request Size: 128 bytes
Link Speed: 5.0 / 8.0 GT/s
Link Width: x1 / x2
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0220: Enhanced Capability 0x0d: Access Control Services
0x0280: Enhanced Capability 0x02: Virtual Channel Capability
0x0a30: Enhanced Capability 0x19: Secondary PCIe Capability
0x0a00: Enhanced Capability 0x1d: Downstream Port Containment
0x0080: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0090: Capability 0x0d: PCI-PCI
0x00a0: Capability 0x01: Power Management
State: D0
0:29:0: Intel Elkhart Lake LH2OSE
0x0000: Vendor ID: 8086, Product ID: 4bb3
0x0004: Command: 0000, Status: 0010
0x0008: Class: 08 System, Subclass: 80 Miscellaneous,
Interface: 35, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083000000/0x00200000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D3
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0:29:1: Intel Elkhart Lake Ethernet
0x0000: Vendor ID: 8086, Product ID: 4ba1
0x0004: Command: 0006, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 18, Revision: 11pcidump: PCIOCGETVPD: Input/output
error
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083400000/0x00040000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0:29:2: Intel Elkhart Lake Ethernet
0x0000: Vendor ID: 8086, Product ID: 4bb1
0x0004: Command: 0006, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 19, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083440000/0x00040000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0080: Capability 0x01: Power Management
State: D0
0x0090: Capability 0x09: Vendor Specific
0x00d0: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0:31:0: Intel Elkhart Lake eSPI
0x0000: Vendor ID: 8086, Product ID: 4b00
0x0004: Command: 0007, Status: 0200
0x0008: Class: 06 Bridge, Subclass: 01 ISA,
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 80, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 00 Line: 00 Min Gnt: 00 Max Lat: 00
0:31:3: Intel Elkhart Lake HD Audio
0x0000: Vendor ID: 8086, Product ID: 4b58
0x0004: Command: 0006, Status: 0010
0x0008: Class: 04 Multimedia, Subclass: 03 HD Audio,
Interface: 80, Revision: 11
0x000c: BIST: 00, Header Type: 00, Latency Timer: 20,
Cache Line Size: 10
0x0010: BAR mem 64bit addr: 0x0000000083494000/0x00004000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR mem 64bit addr: 0x0000000083200000/0x00100000
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0050: Capability 0x01: Power Management
State: D0
0x0080: Capability 0x09: Vendor Specific
0x0060: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: no
0:31:4: Intel Elkhart Lake SMBus
0x0000: Vendor ID: 8086, Product ID: 4b23
0x0004: Command: 0003, Status: 0280
0x0008: Class: 0c Serial Bus, Subclass: 05 SMBus,
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 64bit addr: 0x00000000834aa000/0x00000100
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR io addr: 0x00005040/0x0020
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0:31:5: Intel Elkhart Lake SPI
0x0000: Vendor ID: 8086, Product ID: 4b24
0x0004: Command: 0406, Status: 0000
0x0008: Class: 0c Serial Bus, Subclass: 80 (unknown),
Interface: 00, Revision: 11
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 00
0x0010: BAR mem 32bit addr: 0xfe010000/0x00001000
0x0014: BAR empty (00000000)
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 8086 Product ID: 7270
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 00 Line: 00 Min Gnt: 00 Max Lat: 00
1:0:0: Pericom unknown
0x0000: Vendor ID: 12d8, Product ID: 2303
0x0004: Command: 0007, Status: 0010
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 05
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 1, Secondary Bus: 2, Subordinate Bus: 4,
Secondary Latency Timer: 00
0x001c: I/O Base: 31, I/O Limit: 41, Secondary Status: 0000
0x0020: Memory Base: 8200, Memory Limit: 8230
0x0024: Prefetch Memory Base: fff1, Prefetch Memory Limit: 0001
0x0028: Prefetch Memory Base Upper 32 Bits: ffffffff
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: 0000, I/O Limit Upper 16 Bits: 0000
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 00, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x005c: Capability 0x03: Vital Product Data (VPD)
0x0064: Capability 0x09: Vendor Specific
0x00b0: Capability 0x0d: PCI-PCI
0x00c0: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 128 bytes
Link Speed: 5.0 / 5.0 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x02: Virtual Channel Capability
0x020c: Enhanced Capability 0x04: Power Budgeting
0x0230: Enhanced Capability 0x18: Latency Tolerance Reporting
2:1:0: Pericom unknown
0x0000: Vendor ID: 12d8, Product ID: 2303
0x0004: Command: 0007, Status: 0018
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 05
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 2, Secondary Bus: 3, Subordinate Bus: 3,
Secondary Latency Timer: 00
0x001c: I/O Base: 41, I/O Limit: 41, Secondary Status: 0000
0x0020: Memory Base: 8220, Memory Limit: 8230
0x0024: Prefetch Memory Base: fff1, Prefetch Memory Limit: 0001
0x0028: Prefetch Memory Base Upper 32 Bits: ffffffff
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: 0000, I/O Limit Upper 16 Bits: 0000
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 00, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x004c: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0064: Capability 0x09: Vendor Specific
0x00b0: Capability 0x0d: PCI-PCI
0x00c0: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 128 bytes
Link Speed: 2.5 / 2.5 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x02: Virtual Channel Capability
0x020c: Enhanced Capability 0x04: Power Budgeting
0x0220: Enhanced Capability 0x0d: Access Control Services
2:2:0: Pericom unknown
0x0000: Vendor ID: 12d8, Product ID: 2303
0x0004: Command: 0007, Status: 0018
0x0008: Class: 06 Bridge, Subclass: 04 PCI,
Interface: 00, Revision: 05
0x000c: BIST: 00, Header Type: 01, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR empty (00000000)
0x0014: BAR empty (00000000)
0x0018: Primary Bus: 2, Secondary Bus: 4, Subordinate Bus: 4,
Secondary Latency Timer: 00
0x001c: I/O Base: 31, I/O Limit: 31, Secondary Status: 0000
0x0020: Memory Base: 8200, Memory Limit: 8210
0x0024: Prefetch Memory Base: fff1, Prefetch Memory Limit: 0001
0x0028: Prefetch Memory Base Upper 32 Bits: ffffffff
0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000
0x0030: I/O Base Upper 16 Bits: 0000, I/O Limit Upper 16 Bits: 0000
0x0038: Expansion ROM Base Address: 00000000
0x003c: Interrupt Pin: 00, Line: ff, Bridge Control: 0000
0x0040: Capability 0x01: Power Management
State: D0
0x004c: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0064: Capability 0x09: Vendor Specific
0x00b0: Capability 0x0d: PCI-PCI
0x00c0: Capability 0x10: PCI Express
Max Payload Size: 128 / 256 bytes
Max Read Request Size: 128 bytes
Link Speed: 2.5 / 2.5 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x02: Virtual Channel Capability
0x020c: Enhanced Capability 0x04: Power Budgeting
0x0220: Enhanced Capability 0x0d: Access Control Services
3:0:0: Intel I210
0x0000: Vendor ID: 8086, Product ID: 1533
0x0004: Command: 0007, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 00, Revision: 03
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 32bit addr: 0x82200000/0x00100000
0x0014: BAR empty (00000000)
0x0018: BAR io addr: 0x00004000/0x0020
0x001c: BAR mem 32bit addr: 0x82300000/0x00004000
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: ffff Product ID: 0000
0x0030: Expansion ROM Base Address: fff00000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0070: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 5 (BAR 3:0)
0x00a0: Capability 0x10: PCI Express
Max Payload Size: 128 / 512 bytes
Max Read Request Size: 512 bytes
Link Speed: 2.5 / 2.5 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x03: Device Serial Number
Serial Number: f80278ffff222d06
0x01a0: Enhanced Capability 0x17: TPH Requester
4:0:0: Intel I210
0x0000: Vendor ID: 8086, Product ID: 1533
0x0004: Command: 0007, Status: 0010
0x0008: Class: 02 Network, Subclass: 00 Ethernet,
Interface: 00, Revision: 03
0x000c: BIST: 00, Header Type: 00, Latency Timer: 00,
Cache Line Size: 10
0x0010: BAR mem 32bit addr: 0x82000000/0x00100000
0x0014: BAR empty (00000000)
0x0018: BAR io addr: 0x00003000/0x0020
0x001c: BAR mem 32bit addr: 0x82100000/0x00004000
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: ffff Product ID: 0000
0x0030: Expansion ROM Base Address: fff00000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00
0x0040: Capability 0x01: Power Management
State: D0
0x0050: Capability 0x05: Message Signalled Interrupts (MSI)
Enabled: yes
0x0070: Capability 0x11: Extended Message Signalled Interrupts (MSI-X)
Enabled: no; table size 5 (BAR 3:0)
0x00a0: Capability 0x10: PCI Express
Max Payload Size: 128 / 512 bytes
Max Read Request Size: 512 bytes
Link Speed: 2.5 / 2.5 GT/s
Link Width: x1 / x1
0x0100: Enhanced Capability 0x01: Advanced Error Reporting
0x0140: Enhanced Capability 0x03: Device Serial Number
Serial Number: f80278ffff222d07
0x01a0: Enhanced Capability 0x17: TPH Requester
=== dmesg:
OpenBSD 7.4-current (GENERIC.MP) #1467: Fri Nov 24 22:39:10 MST 2023
dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 16941641728 (16156MB)
avail mem = 16408547328 (15648MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0x62f5a000 (63 entries)
bios0: vendor INSYDE Corp. version "Z01-0003A073" date 2023-03-01
bios0: OnLogic Helix3X0
efi0 at bios0: UEFI 2.8
efi0: INSYDE Corp. rev 0x71384019
acpi0 at bios0: ACPI 6.1
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP UEFI SSDT SSDT SSDT SSDT SSDT SSDT TPM2 SSDT NHLT OEM1
HPET APIC MCFG PRAM RSCI SSDT LPIT WSMT SSDT PSDS DMAR SSDT FPDT BGRT
acpi0: wakeup devices XHCI(S4) XDCI(S4) HDAS(S4) RP01(S4) PXSX(S4) RP02(S4)
PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP05(S4) PXSX(S4) RP06(S4)
PXSX(S4) RP07(S4) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 19200000 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Pentium(R) J6426 @ 2.00GHz, 1995.69 MHz, 06-96-01, patch 00000017
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,WAITPKG,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,IBRS_ALL,SKIP_L1DFL,MDS_NO,IF_PSCHANGE,MISC_PKG_CT,ENERGY_FILT,FB_CLEAR,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu0: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line
12-way L2 cache, 4MB 64b/line 16-way L3 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 38MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.2.2.1.1.1, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Pentium(R) J6426 @ 2.00GHz, 1995.68 MHz, 06-96-01, patch 00000017
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,WAITPKG,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,IBRS_ALL,SKIP_L1DFL,MDS_NO,IF_PSCHANGE,MISC_PKG_CT,ENERGY_FILT,FB_CLEAR,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu1: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line
12-way L2 cache, 4MB 64b/line 16-way L3 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Pentium(R) J6426 @ 2.00GHz, 1995.68 MHz, 06-96-01, patch 00000017
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,WAITPKG,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,IBRS_ALL,SKIP_L1DFL,MDS_NO,IF_PSCHANGE,MISC_PKG_CT,ENERGY_FILT,FB_CLEAR,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu2: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line
12-way L2 cache, 4MB 64b/line 16-way L3 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Pentium(R) J6426 @ 2.00GHz, 1995.68 MHz, 06-96-01, patch 00000017
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,RDSEED,SMAP,CLFLUSHOPT,CLWB,PT,SHA,UMIP,WAITPKG,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,IBRS_ALL,SKIP_L1DFL,MDS_NO,IF_PSCHANGE,MISC_PKG_CT,ENERGY_FILT,FB_CLEAR,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu3: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 1MB 64b/line
12-way L2 cache, 4MB 64b/line 16-way L3 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xc0000000, bus 0-255
acpiprt0 at acpi0: bus 0 (PC00)
acpiprt1 at acpi0: bus -1 (RP01)
acpiprt2 at acpi0: bus -1 (RP02)
acpiprt3 at acpi0: bus -1 (RP03)
acpiprt4 at acpi0: bus -1 (RP04)
acpiprt5 at acpi0: bus 1 (RP05)
acpiprt6 at acpi0: bus -1 (RP06)
acpiprt7 at acpi0: bus -1 (RP07)
acpipci0 at acpi0 PC00: 0x00000000 0x00000011 0x00000001
"INT3511" at acpi0 not configured
"INT3512" at acpi0 not configured
"INT3514" at acpi0 not configured
"ACPI000E" at acpi0 not configured
"INTC1020" at acpi0 not configured
com4 at acpi0 UAH0 addr 0xfe03e000/0x8 irq 16: ns16550a, 16 byte fifo
com5 at acpi0 UAH1 addr 0xfe040000/0x8 irq 17: ns16550a, 16 byte fifo
acpibtn0 at acpi0: SLPB
acpibtn1 at acpi0: PWRB(wakeup)
"INTC1033" at acpi0 not configured
"INTC1033" at acpi0 not configured
"INT33A1" at acpi0 not configured
tpm0 at acpi0 TPM_ 2.0 (CRB) addr 0xfed40000/0x5000, device 0x00000000 rev 0x0
"PNP0C0B" at acpi0 not configured
"PNP0C0B" at acpi0 not configured
"PNP0C0B" at acpi0 not configured
"PNP0C0B" at acpi0 not configured
"PNP0C0B" at acpi0 not configured
acpipwrres0 at acpi0: WRST
acpicpu0 at acpi0: C3(200@1048 mwait.1@0x60), C2(200@253 mwait.1@0x31),
C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(200@1048 mwait.1@0x60), C2(200@253 mwait.1@0x31),
C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(200@1048 mwait.1@0x60), C2(200@253 mwait.1@0x31),
C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(200@1048 mwait.1@0x60), C2(200@253 mwait.1@0x31),
C1(1000@1 mwait.1), PSS
acpipwrres1 at acpi0: FN00, resource for FAN0
acpipwrres2 at acpi0: FN01, resource for FAN1
acpipwrres3 at acpi0: FN02, resource for FAN2
acpipwrres4 at acpi0: FN03, resource for FAN3
acpipwrres5 at acpi0: FN04, resource for FAN4
acpitz0 at acpi0: critical temperature is 119 degC
acpipwrres6 at acpi0: PIN_
cpu0: Enhanced SpeedStep 1995 MHz: speeds: 2001, 2000, 1900, 1800, 1700, 1600,
1500, 1400, 1300, 1200, 1100, 1000, 900, 800 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Elkhart Lake Host" rev 0x01
inteldrm0 at pci0 dev 2 function 0 "Intel UHD Graphics" rev 0x01
drm0 at inteldrm0
inteldrm0: msi, ELKHARTLAKE, gen 11
"Intel Elkhart Lake GNA" rev 0x01 at pci0 dev 8 function 0 not configured
dwiic0 at pci0 dev 16 function 0 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
16
iic0 at dwiic0
dwiic1 at pci0 dev 16 function 1 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
17
iic1 at dwiic1
xhci0 at pci0 dev 20 function 0 "Intel Elkhart Lake xHCI" rev 0x11: msi, xHCI
1.20
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
addr 1
"Intel Elkhart Lake SRAM" rev 0x11 at pci0 dev 20 function 2 not configured
dwiic2 at pci0 dev 21 function 0 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
27
iic2 at dwiic2
dwiic3 at pci0 dev 21 function 1 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
28
iic3 at dwiic3
dwiic4 at pci0 dev 21 function 2 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
29
iic4 at dwiic4
dwiic5 at pci0 dev 21 function 3 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
30
iic5 at dwiic5
"Intel Elkhart Lake HECI" rev 0x11 at pci0 dev 22 function 0 not configured
ahci0 at pci0 dev 23 function 0 "Intel Elkhart Lake AHCI" rev 0x11: msi, AHCI
1.3.1
ahci0: port 1: 6.0Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 1 lun 0: <ATA, TS256GMTS952T2, 02J0> naa.57c35482234925cf
sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
dwiic6 at pci0 dev 25 function 0 "Intel Elkhart Lake I2C" rev 0x11: apic 2 int
31
iic6 at dwiic6
"Intel Elkhart Lake I2C" rev 0x11 at pci0 dev 27 function 0 not configured
"Intel Elkhart Lake I2C" rev 0x11 at pci0 dev 27 function 1 not configured
"Intel Elkhart Lake I2C" rev 0x11 at pci0 dev 27 function 6 not configured
ppb0 at pci0 dev 28 function 0 "Intel Elkhart Lake PCIE" rev 0x11: msi
pci1 at ppb0 bus 1
ppb1 at pci1 dev 0 function 0 vendor "Pericom", unknown product 0x2303 rev 0x05
pci2 at ppb1 bus 2
ppb2 at pci2 dev 1 function 0 vendor "Pericom", unknown product 0x2303 rev
0x05: msi
pci3 at ppb2 bus 3
em0 at pci3 dev 0 function 0 "Intel I210" rev 0x03: msi, address
f8:02:78:22:2d:06
ppb3 at pci2 dev 2 function 0 vendor "Pericom", unknown product 0x2303 rev
0x05: msi
pci4 at ppb3 bus 4
em1 at pci4 dev 0 function 0 "Intel I210" rev 0x03: msi, address
f8:02:78:22:2d:07
"Intel Elkhart Lake LH2OSE" rev 0x11 at pci0 dev 29 function 0 not configured
dwqe0 at pci0 dev 29 function 1 "Intel Elkhart Lake Ethernet" rev 0x11: rev
0x52, address 84:8b:cd:4d:b5:f6
ukphy0 at dwqe0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x19f277, model 0x0030
dwqe1 at pci0 dev 29 function 2 "Intel Elkhart Lake Ethernet" rev 0x11: rev
0x52, address 84:8b:cd:4d:bc:36
ukphy1 at dwqe1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x19f277, model 0x0030
pcib0 at pci0 dev 31 function 0 "Intel Elkhart Lake eSPI" rev 0x11
azalia0 at pci0 dev 31 function 3 "Intel Elkhart Lake HD Audio" rev 0x11: msi
azalia0: no supported codecs
ichiic0 at pci0 dev 31 function 4 "Intel Elkhart Lake SMBus" rev 0x11: apic 2
int 16
iic7 at ichiic0
"Intel Elkhart Lake SPI" rev 0x11 at pci0 dev 31 function 5 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT
efifb at mainbus0 not configured
uhidev0 at uhub0 port 5 configuration 1 interface 0 "LITEON Technology USB
Multimedia Keyboard" rev 1.10/1.01 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd0 at ukbd0: console keyboard
uhidev1 at uhub0 port 5 configuration 1 interface 1 "LITEON Technology USB
Multimedia Keyboard" rev 1.10/1.01 addr 2
uhidev1: iclass 3/0, 1 report id
ucc0 at uhidev1 reportid 1: 8 usages, 6 keys, enum
wskbd1 at ucc0 mux 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (e4946977e6d989c4.a) swap on sd0b dump on sd0b
inteldrm0: 1600x1200, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
wskbd1: connecting to wsdisplay0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
