your PROM is likely setup to boot a "bsd" kernel in the msdos partition, rather than the "boot" file. The "boot" file will load /bsd from the ffs partition.
Amarendra Godbole <amarendra.godb...@gmail.com> wrote: > So I used sysupgrade to upgrade the ERL from 6.7 to 6.8. It went through > everything fine, downloaded the sets, extracts, etc. and reboots. However, > it boots back into the old 6.7 kernel. I can see /bsd.upgrade created, and > /home/_sysupgrade is empty. but did not see any option to trigger the > upgrade. I thought it should have been automatically handled by sysupgrade. > > What did I miss? > > Thanks. > > -Amarendra > > > erl# uname -a > OpenBSD erl.lan 6.7 GENERIC.MP#134 octeon > > erl# ls -l > total 79128 > -rw-r--r-- 1 root wheel 578 May 7 2020 .cshrc > -rw-r--r-- 1 root wheel 468 May 7 2020 .profile > drwxr-xr-x 2 root wheel 512 May 7 2020 altroot > -rw-r--r-- 1 root wheel 160 Mar 31 00:08 auto_upgrade.conf > drwxr-xr-x 2 root wheel 1024 May 7 2020 bin > -rwx------ 1 root wheel 7626800 Mar 31 00:10 bsd > -rwx------ 1 root wheel 7623592 Mar 31 00:01 bsd.booted > -rw------- 1 root wheel 8843608 May 7 2020 bsd.rd > -rw------- 1 root wheel 7568260 May 7 2020 bsd.sp > -rwx------ 1 root wheel 8823044 Mar 31 00:09 bsd.upgrade > drwxr-xr-x 4 root wheel 18432 Mar 31 00:10 dev > drwxr-xr-x 23 root wheel 2048 Mar 31 00:11 etc > drwxr-xr-x 4 root wheel 512 Oct 15 21:09 home > drwxr-xr-x 2 root wheel 512 May 7 2020 mnt > drwx------ 3 root wheel 512 Mar 31 01:30 root > drwxr-xr-x 2 root wheel 1536 May 7 2020 sbin > lrwxrwx--- 1 root wheel 11 May 7 2020 sys -> usr/src/sys > drwxrwxrwt 6 root wheel 512 Mar 31 07:45 tmp > drwxr-xr-x 16 root wheel 512 Sep 7 2020 usr > drwxr-xr-x 23 root wheel 512 May 7 2020 var > erl# > > erl# dmesg > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2020 OpenBSD. All rights reserved. > https://www.OpenBSD.org > > OpenBSD 6.7 (GENERIC.MP) #134: Thu May 7 16:05:06 MDT 2020 > dera...@octeon.openbsd.org:/usr/src/sys/arch/octeon/compile/GENERIC.MP > real mem = 536870912 (512MB) > avail mem = 506740736 (483MB) > mainbus0 at root: board 20002 rev 2.18 > cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation > cpu0: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way > cpu1 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation > cpu1: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way > clock0 at mainbus0: int 5 > octcrypto0 at mainbus0 > iobus0 at mainbus0 > simplebus0 at iobus0: "soc" > octciu0 at simplebus0 > octsmi0 at simplebus0 > octpip0 at simplebus0 > octgmx0 at octpip0 interface 0 > cnmac0 at octgmx0: RGMII, address 78:8a:20:46:a8:c0 > atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2 > cnmac1 at octgmx0: RGMII, address 78:8a:20:46:a8:c1 > atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2 > cnmac2 at octgmx0: RGMII, address 78:8a:20:46:a8:c2 > atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2 > com0 at simplebus0: ns16550a, 64 byte fifo > com0: console > dwctwo0 at iobus0 base 0x1180068000000 irq 56 > usb0 at dwctwo0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev > 2.00/1.00 addr 1 > octrng0 at iobus0 base 0x1400000000000 irq 0 > /dev/ksyms: Symbol table not valid. > umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" > rev 2.10/11.00 addr 2 > umass0: using SCSI over Bulk-Only > scsibus0 at umass0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable > serial.21c40cd1719080003000 > sd0: 30526MB, 512 bytes/sector, 62517248 sectors > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > boot device: sd0 > root on sd0a (2124441bc835a462.a) swap on sd0b dump on sd0b > WARNING: No TOD clock, believing file system. > WARNING: CHECK AND RESET THE DATE!
