Hello,
I cannot change IRQ in Bios,
In BIOS, com0 settings are like this;
IO = 3F8h (correct) , IRQ = 7 (incorrect)
For installation, I set com0's IRQ to 7 at UKC. And I completed
installation successfully. However, when I try to boot after installation
the console is stucking again. There are 16 character on the last line and
com0 are using to IRQ = 4. At this point, I cannot reach the UKC with "boot
-c". How can I overcome this?
"Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 0 not configured
"Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 1 not configured
"Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
"Intel C3000 UART" rev 0x11 at pci0 dev 26 function 0 not configured
"Intel C3000 UART" rev 0x11 at pci0 dev 26 function 1 not configured
"Intel C3000 UART" rev 0x11 at pci0 dev 26 function 2 not configured
sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16
sdhc0: SDHC 3.0, 200 MHz base clock
sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
pcib0 at pci0 dev 31 function 0 "Intel C3000 LPC" rev 0x11
"Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
"Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
"Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
C▒▒+
сJͅ▒▒▒▒с▒▒ɻ▒▒▒J▒Ł▒▒: ns16550a, 16 byte fifo
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33
lm1 at wbsio0 port 0xa10/8: NCT6776F
vmm0 at mainbus0: VMX/EPT
sdmmc0: can't enable card
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (1589b7458f9250cf.a) swap on sd0b dump on sd0b
WARNING: / was not properly unmounted
Automatic boot i
Vertigo Altair <vertigo.alt...@gmail.com>, 3 May 2020 Paz, 17:29 tarihinde
şunu yazdı:
> Hello Again,
> I have already disabled ACPI at the boot prompt, but the result didn't
> change.Thanks for suggestion..
>
> Andrea Fleckenstein <afl...@mailbox.org>, 3 May 2020 Paz, 16:41 tarihinde
> şunu yazdı:
>
>> Vertigo Altair <vertigo.alt...@gmail.com> writes:
>>
>> Hello,
>>
>> I had a Dell XPS 8100 with a similar problem and I was able to get
>> around it by disabling ACPI at the boot prompt. Of course, we have very
>> different machines, but it's worth a shot. Unfortunately the boot was
>> extremely slow, on the order of 10min with acpi reenabled, and several
>> minutes
>> without it. Hopefully someone more knowledgeable than me will give a
>> more reasoned answer. Good luck.
>>
>> Best,
>> Andrea
>>
>> > Hi,
>> > I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it.
>> But
>> > When I try to boot, the boot process is stucking. There is no output
>> after
>> > " erase ^?, werase"
>> >
>> > BIOS Boot Selector for VEP1400-X
>> > Version 3.48.0.9-4
>> >
>> >
>> > POST Configuration
>> > CPU Signature 506F1
>> > CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0
>> > Microcode Revision 2E
>> > Platform ID: 0x0
>> > PMG_CST_CFG_CTL: 0x37
>> > Misc EN: 0x840089
>> > Gen PM ConA: 0xA0A00200
>> > Therm Status: 0x8000000
>> > POST Control=0xEA000F03, Status=0xE600DF00
>> >
>> > BIOS initializations...
>> >
>> > CPGC Memtest Channel 0 ...................... PASS
>> >
>> > POST:
>> > RTC Battery OK at last cold boot
>> > RTC date 5/3/2020 9:24:11
>> >
>> > POST SPD test ............................... PASS
>> >
>> > POST Lower DRAM Memory test .........
>> > POST ECC Test ............................... PASS
>> >
>> > .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20
>> >
>> > POST Lower DRAM Memory test ................. PASS
>> > POST Lower DRAM ECC check ................... PASS
>> >
>> > Current BOOT from Primary BIOS
>> > DxE POST
>> >
>> > POST Upper DRAM Memory test
>> > Short memory cell test
>> >
>> > POST Upper DRAM Memory test ................. PASS
>> > HDD Access .................................. PASS
>> > USB device detected
>> > Temperature test ............................ PASS
>> > FAN controller test ......................... PASS
>> > EEPROM test ................................. PASS
>> > POST PCI test ............................... PASS
>> > POST BMC Interface test ..................... PASS
>> > POST NVRAM check ............................ PASS
>> > POST overall test results ................... PASS
>> >
>> > NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7
>> > Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc.
>> > BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040
>> > Press <DEL> or <F2> to enter setup.
>> > probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M]
>> > disk: hd0 hd1* hd2*
>> >>> OpenBSD/amd64 BOOTX64 3.46
>> > boot> stty com0 115200
>> > boot> set tty com0
>> > switching console to com0
>> >>> OpenBSD/amd64 BOOTX64 3.46
>> > boot>
>> > cannot open hd0a:/etc/random.seed: No such file or directory
>> > booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016
>> > [376562+128+455544+303577]=0xa648d0
>> > entry point at 0x1001000
>> > Copyright (c) 1982, 1986, 1989, 1991, 1993
>> > The Regents of the University of California. All rights
>> reserved.
>> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.
>> > https://www.OpenBSD.org <https://www.openbsd.org/>
>> >
>> > OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019
>> > dera...@amd64.openbsd.org:
>> /usr/src/sys/arch/amd64/compile/RAMDISK_CD
>> > real mem = 17131601920 (16337MB)
>> > avail mem = 16608419840 (15839MB)
>> > mainbus0 at root
>> > bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries)
>> > bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date
>> 06/26/2019
>> > bios0: Dell EMC VEP1445-V220
>> > acpi0 at bios0: ACPI 6.1
>> > acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR
>> SPCR
>> > TPM2 HEST BERT ERST EINJ WSMT
>> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
>> > cpu0 at mainbus0: apid 0 (boot processor)
>> > cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01
>> > cpu0:
>> >
>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
>> > cpu0: 2MB 64b/line 16-way L2 cache
>> > cpu0: apic clock running at 25MHz
>> > cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > cpu at mainbus0: not configured
>> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
>> > acpiprt0 at acpi0: bus 0 (PCI0)
>> > acpiprt1 at acpi0: bus -1 (PEX0)
>> > acpiprt2 at acpi0: bus -1 (PEX1)
>> > acpiprt3 at acpi0: bus 2 (PEX2)
>> > acpiprt4 at acpi0: bus -1 (PEX3)
>> > acpiprt5 at acpi0: bus -1 (PEX4)
>> > acpiprt6 at acpi0: bus 4 (PEX5)
>> > acpiprt7 at acpi0: bus -1 (PEX6)
>> > acpiprt8 at acpi0: bus -1 (PEX7)
>> > acpiprt9 at acpi0: bus 1 (VRP2)
>> > acpiprt10 at acpi0: bus 5 (VRP0)
>> > acpiprt11 at acpi0: bus 7 (VRP1)
>> > acpicpu at acpi0 not configured
>> > acpitz at acpi0 not configured
>> > "PNP0A08" at acpi0 not configured
>> > "PNP0003" at acpi0 not configured
>> > acpicmos0 at acpi0
>> > "MVS6190" at acpi0 not configured
>> > "PICB000" at acpi0 not configured
>> > "INTC3000" at acpi0 not configured
>> > "PNP0C33" at acpi0 not configured
>> > "MSFT0101" at acpi0 not configured
>> > pci0 at mainbus0 bus 0
>> > 0:31:5: mem address conflict 0xfe010000/0x1000
>> > pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
>> > pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
>> > "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
>> > ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
>> > pci1 at ppb0 bus 1
>> > "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
>> > ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11
>> > pci2 at ppb1 bus 2
>> > em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address
>> > 50:9a:4c:ea:96:70
>> > em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address
>> > 50:9a:4c:ea:96:71
>> > em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address
>> > 50:9a:4c:ea:96:72
>> > em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address
>> > 50:9a:4c:ea:96:73
>> > ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11
>> > pci3 at ppb2 bus 4
>> > vendor "Atheros", unknown product 0x003c (class network subclass
>> > miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured
>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
>> > ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI
>> 1.3.1
>> > ahci0: port 5: 6.0Gb/s
>> > scsibus0 at ahci0: 32 targets
>> > sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN>
>> > naa.6611602cbad0d0d0
>> > sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin
>> > xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI
>> 1.0
>> > usb0 at xhci0: USB revision 3.0
>> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev
>> > 3.00/1.00 addr 1
>> > ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
>> > pci4 at ppb3 bus 5
>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured
>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured
>> > ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
>> > pci5 at ppb4 bus 7
>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured
>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured
>> > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
>> > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int
>> 16
>> > sdhc0: SDHC 3.0, 200 MHz base clock
>> > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
>> > "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
>> > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
>> > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
>> > isa0 at mainbus0
>> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
>> > com0: console
>> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
>> > com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo
>> > efifb at mainbus0 not configured
>> > umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer Fit"
>> > rev 2.00/1.00 addr 2
>> > umass0: using SCSI over Bulk-Only
>> > scsibus1 at umass0: 2 targets, initiator 0
>> > sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable
>> > serial.07815571221118104030
>> > sd1: 14664MB, 512 bytes/sector, 30031872 sectors
>> > sdmmc0: can't enable card
>> > softraid0 at root
>> > scsibus2 at softraid0: 256 targets
>> > root on rd0a swap on rd0b dump on rd0b
>> > erase ^?, werase
>>
>
