Vertigo Altair <vertigo.alt...@gmail.com> writes: Hello,
I had a Dell XPS 8100 with a similar problem and I was able to get around it by disabling ACPI at the boot prompt. Of course, we have very different machines, but it's worth a shot. Unfortunately the boot was extremely slow, on the order of 10min with acpi reenabled, and several minutes without it. Hopefully someone more knowledgeable than me will give a more reasoned answer. Good luck. Best, Andrea > Hi, > I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it. But > When I try to boot, the boot process is stucking. There is no output after > " erase ^?, werase" > > BIOS Boot Selector for VEP1400-X > Version 3.48.0.9-4 > > > POST Configuration > CPU Signature 506F1 > CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0 > Microcode Revision 2E > Platform ID: 0x0 > PMG_CST_CFG_CTL: 0x37 > Misc EN: 0x840089 > Gen PM ConA: 0xA0A00200 > Therm Status: 0x8000000 > POST Control=0xEA000F03, Status=0xE600DF00 > > BIOS initializations... > > CPGC Memtest Channel 0 ...................... PASS > > POST: > RTC Battery OK at last cold boot > RTC date 5/3/2020 9:24:11 > > POST SPD test ............................... PASS > > POST Lower DRAM Memory test ......... > POST ECC Test ............................... PASS > > .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20 > > POST Lower DRAM Memory test ................. PASS > POST Lower DRAM ECC check ................... PASS > > Current BOOT from Primary BIOS > DxE POST > > POST Upper DRAM Memory test > Short memory cell test > > POST Upper DRAM Memory test ................. PASS > HDD Access .................................. PASS > USB device detected > Temperature test ............................ PASS > FAN controller test ......................... PASS > EEPROM test ................................. PASS > POST PCI test ............................... PASS > POST BMC Interface test ..................... PASS > POST NVRAM check ............................ PASS > POST overall test results ................... PASS > > NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7 > Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc. > BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040 > Press <DEL> or <F2> to enter setup. > probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M] > disk: hd0 hd1* hd2* >>> OpenBSD/amd64 BOOTX64 3.46 > boot> stty com0 115200 > boot> set tty com0 > switching console to com0 >>> OpenBSD/amd64 BOOTX64 3.46 > boot> > cannot open hd0a:/etc/random.seed: No such file or directory > booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016 > [376562+128+455544+303577]=0xa648d0 > entry point at 0x1001000 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2019 OpenBSD. All rights reserved. > https://www.OpenBSD.org <https://www.openbsd.org/> > > OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019 > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD > real mem = 17131601920 (16337MB) > avail mem = 16608419840 (15839MB) > mainbus0 at root > bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries) > bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date 06/26/2019 > bios0: Dell EMC VEP1445-V220 > acpi0 at bios0: ACPI 6.1 > acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR SPCR > TPM2 HEST BERT ERST EINJ WSMT > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat > cpu0 at mainbus0: apid 0 (boot processor) > cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01 > cpu0: > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES > cpu0: 2MB 64b/line 16-way L2 cache > cpu0: apic clock running at 25MHz > cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE > cpu at mainbus0: not configured > cpu at mainbus0: not configured > cpu at mainbus0: not configured > cpu at mainbus0: not configured > cpu at mainbus0: not configured > cpu at mainbus0: not configured > cpu at mainbus0: not configured > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus -1 (PEX0) > acpiprt2 at acpi0: bus -1 (PEX1) > acpiprt3 at acpi0: bus 2 (PEX2) > acpiprt4 at acpi0: bus -1 (PEX3) > acpiprt5 at acpi0: bus -1 (PEX4) > acpiprt6 at acpi0: bus 4 (PEX5) > acpiprt7 at acpi0: bus -1 (PEX6) > acpiprt8 at acpi0: bus -1 (PEX7) > acpiprt9 at acpi0: bus 1 (VRP2) > acpiprt10 at acpi0: bus 5 (VRP0) > acpiprt11 at acpi0: bus 7 (VRP1) > acpicpu at acpi0 not configured > acpitz at acpi0 not configured > "PNP0A08" at acpi0 not configured > "PNP0003" at acpi0 not configured > acpicmos0 at acpi0 > "MVS6190" at acpi0 not configured > "PICB000" at acpi0 not configured > "INTC3000" at acpi0 not configured > "PNP0C33" at acpi0 not configured > "MSFT0101" at acpi0 not configured > pci0 at mainbus0 bus 0 > 0:31:5: mem address conflict 0xfe010000/0x1000 > pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11 > pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11 > "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured > ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11 > pci1 at ppb0 bus 1 > "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured > ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11 > pci2 at ppb1 bus 2 > em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address > 50:9a:4c:ea:96:70 > em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address > 50:9a:4c:ea:96:71 > em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address > 50:9a:4c:ea:96:72 > em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address > 50:9a:4c:ea:96:73 > ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11 > pci3 at ppb2 bus 4 > vendor "Atheros", unknown product 0x003c (class network subclass > miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured > "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured > ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI 1.3.1 > ahci0: port 5: 6.0Gb/s > scsibus0 at ahci0: 32 targets > sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN> > naa.6611602cbad0d0d0 > sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin > xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI 1.0 > usb0 at xhci0: USB revision 3.0 > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev > 3.00/1.00 addr 1 > ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11 > pci4 at ppb3 bus 5 > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured > ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11 > pci5 at ppb4 bus 7 > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16 > sdhc0: SDHC 3.0, 200 MHz base clock > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma > "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured > isa0 at mainbus0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo > efifb at mainbus0 not configured > umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer Fit" > rev 2.00/1.00 addr 2 > umass0: using SCSI over Bulk-Only > scsibus1 at umass0: 2 targets, initiator 0 > sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable > serial.07815571221118104030 > sd1: 14664MB, 512 bytes/sector, 30031872 sectors > sdmmc0: can't enable card > softraid0 at root > scsibus2 at softraid0: 256 targets > root on rd0a swap on rd0b dump on rd0b > erase ^?, werase
