thanks for that
[] 's 2017-10-17 22:22 GMT-02:00 Jonathan Gray <j...@jsg.id.au>: > On Tue, Oct 17, 2017 at 04:48:19PM -0700, Carlos Cardenas wrote: > > Howdy. > > > > I found a working USB (Sandisk Cruzer Fit 8GB) to install 6.2 on a RPI3. > > > > Install went fine and so was first boot, then I noticed that relinking > > the kernel failed. > > > > Below is my dmesg and error log. > > > > I thought it might have been due to the clock being way skewed by I > > sync'ed it manually and still run into the same error. > > > > Any pointers on how to proceed? > > The version of lld (4.0.0) in 6.2 could not handle the linker script > required for that. Snapshots have llvm/lld 5.0.0 and relinking should > work there. > > > > > +--+ > > Carlos > > OpenBSD 6.2 (GENERIC) #34: Tue Oct 3 23:53:05 MDT 2017 > > dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC > > real mem = 964972544 (920MB) > > avail mem = 909017088 (866MB) > > mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2 > > cpu0 at mainbus0: ARM Cortex-A53 r0p4 > > simplefb0 at mainbus0: 656x416 > > wsdisplay0 at simplefb0 mux 1 > > wsdisplay0: screen 0 added (std, vt100 emulation) > > simplebus0 at mainbus0: "soc" > > bcmintc0 at simplebus0 > > bcmdog0 at simplebus0 > > pluart0 at simplebus0 > > bcmaux0 at simplebus0 > > com0 at simplebus0: ns16550, no working fifo > > com0: console > > dwctwo0 at simplebus0 > > agtimer0 at simplebus0: tick rate 19200 KHz > > syscon0 at simplebus0 > > simplebus1 at mainbus0: "clocks" > > usb0 at dwctwo0: USB revision 2.0 > > uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev > 2.00/1.00 addr 1 > > uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems > product 0x9514" rev 2.00/2.00 addr 2 > > smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems > SMSC9512/14" rev 2.00/2.00 addr 3 > > smsc0: address b8:27:eb:1c:06:b7 > > ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x0001f0, model 0x000c > > umass0 at uhub1 port 5 configuration 1 interface 0 "SanDisk Cruzer Fit" > rev 2.10/1.00 addr 4 > > umass0: using SCSI over Bulk-Only > > scsibus0 at umass0: 2 targets, initiator 0 > > sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct > removable serial.07815571040905110075 > > sd0: 7632MB, 512 bytes/sector, 15630336 sectors > > vscsi0 at root > > scsibus1 at vscsi0: 256 targets > > softraid0 at root > > scsibus2 at softraid0: 256 targets > > bootfile: sd0a:/bsd > > boot device: sd0 > > root on sd0a (b045dd5058980495.a) swap on sd0b dump on sd0b > > WARNING: CHECK AND RESET THE DATE! > > > > > > # cat /usr/share/compile/GENERIC/relink.log > > (SHA256) /bsd: OK > > LD="ld" sh makegap.sh 0xd4d4d4d4 gapdummy.o > > ld: error: gap.link:11: unknown command ; > > ld: error: gap.link:11: LONG(0xd4d4d4d4); > > ld: error: gap.link:11: ^ > > ld: error: cannot open gapdummy.o: No such file or directory > > ld: error: target emulation unknown: -m or at least one .o file required > > *** Error 1 in /usr/share/compile/GENERIC (Makefile:529 'newbsd') > > > >
