On 10/17/17 17:22, Jonathan Gray wrote:
On Tue, Oct 17, 2017 at 04:48:19PM -0700, Carlos Cardenas wrote:
Howdy.
I found a working USB (Sandisk Cruzer Fit 8GB) to install 6.2 on a RPI3.
Install went fine and so was first boot, then I noticed that relinking
the kernel failed.
Below is my dmesg and error log.
I thought it might have been due to the clock being way skewed by I
sync'ed it manually and still run into the same error.
Any pointers on how to proceed?
The version of lld (4.0.0) in 6.2 could not handle the linker script
required for that. Snapshots have llvm/lld 5.0.0 and relinking should
work there.
That worked.
Thanks.
+--+
Carlos
+--+
Carlos
OpenBSD 6.2 (GENERIC) #34: Tue Oct 3 23:53:05 MDT 2017
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC
real mem = 964972544 (920MB)
avail mem = 909017088 (866MB)
mainbus0 at root: Raspberry Pi 3 Model B Rev 1.2
cpu0 at mainbus0: ARM Cortex-A53 r0p4
simplefb0 at mainbus0: 656x416
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
simplebus0 at mainbus0: "soc"
bcmintc0 at simplebus0
bcmdog0 at simplebus0
pluart0 at simplebus0
bcmaux0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
dwctwo0 at simplebus0
agtimer0 at simplebus0: tick rate 19200 KHz
syscon0 at simplebus0
simplebus1 at mainbus0: "clocks"
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev
2.00/1.00 addr 1
uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems product
0x9514" rev 2.00/2.00 addr 2
smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems
SMSC9512/14" rev 2.00/2.00 addr 3
smsc0: address b8:27:eb:1c:06:b7
ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x0001f0, model 0x000c
umass0 at uhub1 port 5 configuration 1 interface 0 "SanDisk Cruzer Fit" rev
2.10/1.00 addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.00> SCSI4 0/direct
removable serial.07815571040905110075
sd0: 7632MB, 512 bytes/sector, 15630336 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (b045dd5058980495.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
# cat /usr/share/compile/GENERIC/relink.log
(SHA256) /bsd: OK
LD="ld" sh makegap.sh 0xd4d4d4d4 gapdummy.o
ld: error: gap.link:11: unknown command ;
ld: error: gap.link:11: LONG(0xd4d4d4d4);
ld: error: gap.link:11: ^
ld: error: cannot open gapdummy.o: No such file or directory
ld: error: target emulation unknown: -m or at least one .o file required
*** Error 1 in /usr/share/compile/GENERIC (Makefile:529 'newbsd')
