Hi All,
On 13 December 2015 at 05:22, Ted Unangst <t...@tedunangst.com> wrote:
> jungle Boogie wrote:
>> Hello All,
>>
>> Despite the very helpful reply from Daniel on this thread:
>> http://marc.info/?l=openbsd-misc&m=144937777626054&w=2
>>
>> I'm faced with the same message upon accepting the default partition
>> and disk layout:
>> disklabel(19593): syscall 5 "cpath"
>> Abort trap
>>
>> When attempting to use the Octeon snapshot from November:
>> http://ftp.openbsd.org/pub/OpenBSD/snapshots/octeon/
>>
>> Is there something more I can do to get this working or is this some
>> pledge issue? To rule out a USB disk problem or edge router lite
>> problem, I can load the previous bsd.rd file but I would need someone
>> to share that with me because I don't have it anymore.
>
> You need a newer snapshot with a fix for disklabel.
Daniel and I worked things out earlier in the week and I got my edge
router lite booted up. I'm happy to have this platform sponsored by
openBSD and I hope it remains.
Here's the dmesg:
$ dmesg
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.8-current (GENERIC) #1: Thu Nov 26 15:01:01 CET 2015
jas...@erl-2.jasper.la:/usr/src/sys/arch/octeon/compile/GENERIC
real mem = 247463936 (236MB)
avail mem = 245170176 (233MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: Cavium OCTEON CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 8KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 "Octeon DWC2 root hub" rev 2.00/1.00 addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000 irq 48
cnmac0 at cn30xxgmx0: RGMII, address 00:be:ef:10:00:00
atphy0 at cnmac0 phy 7: F1 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 00:be:ef:10:00:01
atphy1 at cnmac1 phy 6: F1 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 00:be:ef:10:00:02
atphy2 at cnmac2 phy 5: F1 10/100/1000 PHY, rev. 2
uartbus0 at mainbus0
com0 at uartbus0 base 0x1180000000800 irq 34: ns16550, no working fifo
com0: console
com1 at uartbus0 base 0x1180000000c00 irq 35: ns16550, no working fifo
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "Kingston
DataTraveler 2.0" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Kingston, DataTraveler 2.0, PMAP> SCSI2
0/direct removable serial.09306545EE21BA140020
sd0: 14887MB, 512 bytes/sector, 30489408 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (0e569f35522c5ff9.a) swap on sd0b dump on sd0b
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
Thank you Daniel for your assistance!
--
-------
inum: 883510009027723
sip: jungleboo...@sip2sip.info
xmpp: jungle-boo...@jit.si
