On Fri, Nov 14, 2014 at 11:59:26AM -0800, patrick keshishian wrote:
> Hi,
>
> On 11/14/14, Etienne <etienne.m...@magickarpet.org> wrote:
> > Hello list,
> >
> > I seem to have a little hardware related problem. I have been using a
> > Lenovo x120e for some time, and OpenBSD ran nicely on it until April. As
> > soon as I upgraded to 5.5, and from quite early after kernel loading,
> > the console started showing and repeating at regular intervals:
> >
> > acpitz0: critical temperature reached 93C, shutting down
> > acpithinkpad0: Unknown event 0x6022
>
> I don't believe I have ever seen the issue you describe with
> my x120e.
>
> hw.vendor=LENOVO
> hw.version=ThinkPad X120e
>
> hw.sensors.acpitz0.temp0=75.00 degC (zone temperature)
> hw.sensors.acpithinkpad0.temp0=75.00 degC
> hw.sensors.acpithinkpad0.temp1=0.00 degC
> hw.sensors.acpithinkpad0.temp2=75.00 degC
> hw.sensors.acpithinkpad0.temp3=0.00 degC
> hw.sensors.acpithinkpad0.temp4=0.00 degC
> hw.sensors.acpithinkpad0.temp5=0.00 degC
> hw.sensors.acpithinkpad0.temp6=27.00 degC
> hw.sensors.acpithinkpad0.temp7=0.00 degC
> hw.sensors.km0.temp0=75.88 degC
>
> hw.sensors.acpithinkpad0.fan0=441 RPM
>
>
> > ("93C" is just a typical value, I've seen any between 92 and 98). I
> > usually have just the time to log in before the system logs me out and
> > shuts down. This laptop normally runs at around 80?C, and I think the
> > temperature reading in OpenBSD is correct, because I get similar
> > warnings
> > and temperature values when I reboot immediately into another OS.
>
> That may be a hint that something may be wrong
> with your cooling. Dust blockage, etc.
>
>
> > Booting on 5.6 bsd.rd and upgrading the system went fine, but as soon as
> > I restarted the system, the same situation happened. Feeling
> > adventurous,
> > I tried to disable acpitz* during the boot process, which made the
> > messages
> > go away. The system ran just below 100?C (as reported by sysctl) for
> > some time without any problem, until I didn't want to take the risk for
> > any longer and shut it down manually. I also have an x100e from the same
> > brand, quite similar even if older and slower, which does _NOT_ show the
> > same symptoms. I'm attaching the dmesg and sysctl hw.sensors output of
> > both
> > machines running 5.6.
> >
> > Has anyone been running 5.5 and 5.6 on a x120e? Any clues on what I
> > should
> > do to diagnose the problem any better?
>
> As I say, I never have had this issue with x120e, which I've
> been using for over 3 years with OpenBSD, mainly following
> snapshots.
>
> Running older snapshot atm:
> $ sysctl kern.version
> kern.version=OpenBSD 5.6-current (GENERIC.MP) #368: Tue Sep 9 00:28:20 MDT
> 2014
> t...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
>
> I have a Gateway LT31 (?) that used to have similar issue as
> you describe. After first cold boot, it would immediately
> shutdown because of temperature warning. Next boot, it
> would be fine.
>
> However, since the last snapshot I put on it, from Sep. It
> hasn't exhibited this behavior. Then again, the Gateway isn't
> used much; so it could be that I've been lucky.
>
I fixed the bogus shutdowns at the last hackathon (the ones where acpitz(4)
would
return temperatures in the 4000-5000K range).
-ml
> --patrick
>
> >
> > Cheers!
> >
> > --
> > ?tienne
> > OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 1861025792 (1774MB)
> > avail mem = 1802760192 (1719MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xf09b0 (43 entries)
> > bios0: vendor LENOVO version "6XET45WW (1.28 )" date 09/17/2010
> > bios0: LENOVO 35089CU
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP TCPA SSDT APIC MCFG HPET SLIC
> > acpi0: wakeup devices PB5_(S5) OHC0(S3) OHC1(S3) OHC2(S3) OHC3(S3) OHC4(S3)
> > P2P_(S5) LID_(S3)
> > acpitimer0 at acpi0: 3579545 Hz, 32 bits
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: AMD Athlon(tm) Neo X2 Dual Core Processor L335, 1597.30 MHz
> > cpu0:
> > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
> > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 256KB
> > 64b/line 16-way L2 cache
> > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully
> > associative
> > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully
> > associative
> > mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 199MHz
> > cpu1 at mainbus0: apid 1 (application processor)
> > cpu1: AMD Athlon(tm) Neo X2 Dual Core Processor L335, 1596.00 MHz
> > cpu1:
> > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
> > cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 256KB
> > 64b/line 16-way L2 cache
> > cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully
> > associative
> > cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully
> > associative
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
> > acpimcfg0 at acpi0 addr 0xe0000000, bus 0-3
> > acpihpet0 at acpi0: 14318180 Hz
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus 2 (PB5_)
> > acpiprt2 at acpi0: bus 4 (P2P_)
> > acpiprt3 at acpi0: bus 1 (AGP_)
> > acpiec0 at acpi0
> > acpicpu0 at acpi0: C3, C2, PSS
> > acpicpu1 at acpi0: PSS
> > acpitz0 at acpi0: critical temperature is 92 degC
> > acpibtn0 at acpi0: PWRB
> > acpibtn1 at acpi0: SLPB
> > acpithinkpad0 at acpi0
> > acpiac0 at acpi0: AC unit online
> > acpibat0 at acpi0: BAT1 model "42T4787" serial 626 oem "SONY"
> > acpibtn2 at acpi0: LID_
> > cpu0: PowerNow! K8 1597 MHz: speeds: 1600 800 MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "AMD RS780 Host" rev 0x00
> > ppb0 at pci0 dev 1 function 0 "AMD RS780 PCIE" rev 0x00
> > pci1 at ppb0 bus 1
> > radeondrm0 at pci1 dev 5 function 0 "ATI Radeon HD 3200" rev 0x00
> > drm0 at radeondrm0
> > radeondrm0: apic 2 int 18
> > ppb1 at pci0 dev 5 function 0 "AMD RS780 PCIE" rev 0x00: msi
> > pci2 at ppb1 bus 2
> > re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x03: RTL8168D/8111D
> > (0x2800), msi, address c8:0a:a9:6a:6c:6b
> > rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
> > ppb2 at pci0 dev 6 function 0 "AMD RS780 PCIE" rev 0x00: msi
> > pci3 at ppb2 bus 3
> > "Realtek 8192SE" rev 0x10 at pci3 dev 0 function 0 not configured
> > ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: apic 2 int 22,
> > AHCI 1.1
> > scsibus1 at ahci0: 32 targets
> > sd0 at scsibus1 targ 0 lun 0: <ATA, ST9250315AS, 0020> SCSI3 0/direct fixed
> > naa.5000c50022882f8c
> > sd0: 238475MB, 512 bytes/sector, 488397168 sectors
> > ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16,
> > version 1.0, legacy support
> > ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16,
> > version 1.0, legacy support
> > ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> > ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> > version 1.0, legacy support
> > ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19
> > usb1 at ehci1: USB revision 2.0
> > uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> > piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x3c: SMI
> > iic0 at piixpm0
> > spdmem0 at iic0 addr 0x51: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
> > azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int
> > 16
> > azalia0: codecs: Conexant/0x5066
> > audio0 at azalia0
> > pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x00
> > ppb3 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
> > pci4 at ppb3 bus 4
> > pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
> > pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
> > pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
> > kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev
> > BH-G2
> > usb2 at ohci0: USB revision 1.0
> > uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> > usb3 at ohci1: USB revision 1.0
> > uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> > usb4 at ohci2: USB revision 1.0
> > uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard
> > pms0 at pckbc0 (aux slot)
> > pckbc0: using irq 12 for aux slot
> > wsmouse0 at pms0 mux 0
> > wsmouse1 at pms0 mux 0
> > pms0: Synaptics touchpad, firmware 7.4
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > umass0 at uhub1 port 1 configuration 1 interface 0 "Generic USB2.0-CRW" rev
> > 2.00/58.88 addr 2
> > umass0: using SCSI over Bulk-Only
> > scsibus2 at umass0: 2 targets, initiator 0
> > sd1 at scsibus2 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
> > removable serial.0bda0158114173400000
> > uvideo0 at uhub1 port 2 configuration 1 interface 0 "Image Processor
> > Integrated Camera" rev 2.00/30.08 addr 3
> > video0 at uvideo0
> > vscsi0 at root
> > scsibus3 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus4 at softraid0: 256 targets
> > root on sd0a (cf86459bc41d995b.a) swap on sd0b dump on sd0b
> > drm: initializing kernel modesetting (RS780 0x1002:0x9612 0x17AA:0x21B2).
> > radeondrm0: VRAM: 336M 0x00000000C0000000 - 0x00000000D4FFFFFF (336M used)
> > radeondrm0: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
> > drm: PCIE GART of 512M enabled (table at 0x00000000C0040000).
> > radeondrm0: 1366x768
> > wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
> > wskbd0
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > hw.sensors.acpitz0.temp0=47.00 degC (zone temperature)
> > hw.sensors.acpithinkpad0.temp0=0.00 degC
> > hw.sensors.acpithinkpad0.temp1=47.00 degC
> > hw.sensors.acpithinkpad0.temp2=0.00 degC
> > hw.sensors.acpithinkpad0.temp3=0.00 degC
> > hw.sensors.acpithinkpad0.temp4=0.00 degC
> > hw.sensors.acpithinkpad0.temp5=0.00 degC
> > hw.sensors.acpithinkpad0.temp6=0.00 degC
> > hw.sensors.acpithinkpad0.temp7=0.00 degC
> > hw.sensors.acpithinkpad0.fan0=467 RPM
> > hw.sensors.acpiac0.indicator0=On (power supply)
> > hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
> > hw.sensors.acpibat0.volt1=0.00 VDC (current voltage)
> > hw.sensors.acpibat0.power0=0.00 W (rate)
> > hw.sensors.acpibat0.watthour0=15.33 Wh (last full capacity)
> > hw.sensors.acpibat0.watthour1=2.81 Wh (warning capacity)
> > hw.sensors.acpibat0.watthour2=0.56 Wh (low capacity)
> > hw.sensors.acpibat0.watthour3=0.00 Wh (remaining capacity), CRITICAL
> > hw.sensors.acpibat0.watthour4=56.16 Wh (design capacity)
> > hw.sensors.acpibat0.raw0=0 (battery idle), OK
> > hw.sensors.acpibtn2.indicator0=On (lid open)
> > hw.sensors.kate0.temp0=47.25 degC
> > hw.sensors.kate0.temp1=45.75 degC
> > hw.sensors.kate0.temp2=54.00 degC
> > hw.sensors.kate0.temp3=51.00 degC
> > OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
> > dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> > real mem = 3850960896 (3672MB)
> > avail mem = 3739664384 (3566MB)
> > User Kernel Config
> > UKC> disable acpitz
> > 368 acpitz* disabled
> > UKC> exit
> > Continuing...
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root
> > bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xf9ba0 (58 entries)
> > bios0: vendor LENOVO version "8FET32WW (1.16 )" date 11/03/2011
> > bios0: LENOVO 0596A28
> > acpi0 at bios0: rev 2
> > acpi0: sleep states S0 S3 S4 S5
> > acpi0: tables DSDT FACP SLIC HPET APIC MCFG UEFI UEFI SSDT SSDT UEFI
> > acpi0: wakeup devices PB4_(S4) PB5_(S4) PB6_(S4) PB7_(S4) OHC1(S3) OHC2(S3)
> > EHC2(S3) OHC3(S3) EHC3(S3) OHC4(S3) SBAZ(S4) GEC_(S4) P2P_(S5) SPB0(S4)
> > SPB1(S4) SPB2(S4) [...]
> > acpitimer0 at acpi0: 3579545 Hz, 32 bits
> > acpihpet0 at acpi0: 14318180 Hz
> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> > cpu0 at mainbus0: apid 0 (boot processor)
> > cpu0: AMD E-350 Processor, 6706.74 MHz
> > cpu0:
> > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,PAGE1GB,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
> > cpu0: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
> > 64b/line 16-way L2 cache
> > cpu0: 8 4MB entries fully associative
> > cpu0: DTLB 40 4KB entries fully associative, 8 4MB entries fully
> > associative
> > cpu0: smt 0, core 0, package 0
> > mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> > cpu0: apic clock running at 199MHz
> > cpu0: mwait min=64, max=64, C-substates=0.0.0.0.0, IBE
> > cpu1 at mainbus0: apid 1 (application processor)
> > cpu1: AMD E-350 Processor, 1596.60 MHz
> > cpu1:
> > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,PAGE1GB,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
> > cpu1: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
> > 64b/line 16-way L2 cache
> > cpu1: 8 4MB entries fully associative
> > cpu1: DTLB 40 4KB entries fully associative, 8 4MB entries fully
> > associative
> > cpu1: smt 0, core 1, package 0
> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
> > ioapic0: misconfigured as apic 0, remapped to apid 2
> > acpimcfg0 at acpi0 addr 0xf8000000, bus 0-31
> > acpiprt0 at acpi0: bus 0 (PCI0)
> > acpiprt1 at acpi0: bus -1 (PB4_)
> > acpiprt2 at acpi0: bus -1 (PB5_)
> > acpiprt3 at acpi0: bus 1 (PB6_)
> > acpiprt4 at acpi0: bus -1 (PB7_)
> > acpiprt5 at acpi0: bus 2 (P2P_)
> > acpiprt6 at acpi0: bus 3 (SPB0)
> > acpiprt7 at acpi0: bus 4 (SPB1)
> > acpiprt8 at acpi0: bus -1 (SPB2)
> > acpiprt9 at acpi0: bus -1 (SPB3)
> > acpiec0 at acpi0
> > acpicpu0 at acpi0: C2, PSS
> > acpicpu1 at acpi0: C2, PSS
> > acpitz at acpi0 not configured
> > acpibtn0 at acpi0: PWRB
> > acpibtn1 at acpi0: SLPB
> > acpithinkpad0 at acpi0
> > acpiac0 at acpi0: AC unit online
> > acpibat0 at acpi0: BAT1 model "42T4787" serial 2692 type LION oem "SONY"
> > acpibtn2 at acpi0: LID_
> > cpu0: 6706 MHz: speeds: 1600 1280 800 MHz
> > pci0 at mainbus0 bus 0
> > pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
> > radeondrm0 at pci0 dev 1 function 0 "ATI Radeon HD 6310" rev 0x00
> > drm0 at radeondrm0
> > radeondrm0: msi
> > azalia0 at pci0 dev 1 function 1 "ATI Radeon HD 6310 HD Audio" rev 0x00:
> > msi
> > azalia0: no supported codecs
> > ppb0 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00: msi
> > pci1 at ppb0 bus 1
> > re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x03: RTL8168D/8111D
> > (0x2800), msi, address 04:7d:7b:3d:9c:5f
> > rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
> > ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: apic 2 int 19,
> > AHCI 1.2
> > scsibus1 at ahci0: 32 targets
> > sd0 at scsibus1 targ 0 lun 0: <ATA, ST9500423AS, 0001> SCSI3 0/direct fixed
> > naa.5000c50038ba9b3e
> > sd0: 476940MB, 512 bytes/sector, 976773168 sectors
> > ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> > version 1.0, legacy support
> > ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> > ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> > version 1.0, legacy support
> > ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> > usb1 at ehci1: USB revision 2.0
> > uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> > piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x42: polling
> > iic0 at piixpm0
> > spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-8500 SO-DIMM
> > azalia1 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x40: apic 2 int
> > 16
> > azalia1: codecs: Conexant/0x5066
> > audio0 at azalia1
> > pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x40
> > ppb1 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
> > pci2 at ppb1 bus 2
> > ppb2 at pci0 dev 21 function 0 "ATI SB800 PCIE" rev 0x00
> > pci3 at ppb2 bus 3
> > ppb3 at pci0 dev 21 function 1 "ATI SB800 PCIE" rev 0x00: msi
> > pci4 at ppb3 bus 4
> > "Realtek 8188CE" rev 0x01 at pci4 dev 0 function 0 not configured
> > pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
> > pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
> > pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
> > km0 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
> > pchb4 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
> > pchb5 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
> > pchb6 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
> > pchb7 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
> > usb2 at ohci0: USB revision 1.0
> > uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> > usb3 at ohci1: USB revision 1.0
> > uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> > isa0 at pcib0
> > isadma0 at isa0
> > pckbc0 at isa0 port 0x60/5
> > pckbd0 at pckbc0 (kbd slot)
> > pckbc0: using irq 1 for kbd slot
> > wskbd0 at pckbd0: console keyboard
> > pms0 at pckbc0 (aux slot)
> > pckbc0: using irq 12 for aux slot
> > wsmouse0 at pms0 mux 0
> > wsmouse1 at pms0 mux 0
> > pms0: Synaptics touchpad, firmware 7.5
> > pcppi0 at isa0 port 0x61
> > spkr0 at pcppi0
> > uvideo0 at uhub1 port 5 configuration 1 interface 0 "Image Processor
> > Integrated Camera" rev 2.00/30.08 addr 2
> > video0 at uvideo0
> > ugen0 at uhub2 port 4 "Broadcom Corp Broadcom Bluetooth Device" rev
> > 2.00/7.48 addr 2
> > vscsi0 at root
> > scsibus2 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > root on sd0a (dbbd96bdfb0cefb8.a) swap on sd0b dump on sd0b
> > drm: initializing kernel modesetting (PALM 0x1002:0x9802 0x17AA:0x21DF).
> > radeondrm0: VRAM: 384M 0x0000000000000000 - 0x0000000017FFFFFF (384M used)
> > radeondrm0: GTT: 512M 0x0000000018000000 - 0x0000000037FFFFFF
> > drm: PCIE GART of 512M enabled (table at 0x0000000000040000).
> > drm: Internal thermal controller without fan control
> > radeondrm0: 1366x768
> > wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
> > wskbd0
> > wsdisplay0: screen 1-5 added (std, vt100 emulation)
> > hw.sensors.acpithinkpad0.temp0=99.00 degC
> > hw.sensors.acpithinkpad0.temp1=0.00 degC
> > hw.sensors.acpithinkpad0.temp2=99.00 degC
> > hw.sensors.acpithinkpad0.temp3=0.00 degC
> > hw.sensors.acpithinkpad0.temp4=0.00 degC
> > hw.sensors.acpithinkpad0.temp5=0.00 degC
> > hw.sensors.acpithinkpad0.temp6=36.00 degC
> > hw.sensors.acpithinkpad0.temp7=0.00 degC
> > hw.sensors.acpithinkpad0.fan0=379 RPM
> > hw.sensors.acpiac0.indicator0=On (power supply)
> > hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
> > hw.sensors.acpibat0.volt1=12.16 VDC (current voltage)
> > hw.sensors.acpibat0.power0=0.00 W (rate)
> > hw.sensors.acpibat0.watthour0=48.06 Wh (last full capacity)
> > hw.sensors.acpibat0.watthour1=2.53 Wh (warning capacity)
> > hw.sensors.acpibat0.watthour2=0.51 Wh (low capacity)
> > hw.sensors.acpibat0.watthour3=42.35 Wh (remaining capacity), OK
> > hw.sensors.acpibat0.watthour4=50.54 Wh (design capacity)
> > hw.sensors.acpibat0.raw0=2 (battery charging), OK
> > hw.sensors.acpibtn2.indicator0=On (lid open)
> > hw.sensors.km0.temp0=99.50 degC
