Hi,
On 11/14/14, Etienne <etienne.m...@magickarpet.org> wrote:
> Hello list,
>
> I seem to have a little hardware related problem. I have been using a
> Lenovo x120e for some time, and OpenBSD ran nicely on it until April. As
> soon as I upgraded to 5.5, and from quite early after kernel loading,
> the console started showing and repeating at regular intervals:
>
> acpitz0: critical temperature reached 93C, shutting down
> acpithinkpad0: Unknown event 0x6022
I don't believe I have ever seen the issue you describe with
my x120e.
hw.vendor=LENOVO
hw.version=ThinkPad X120e
hw.sensors.acpitz0.temp0=75.00 degC (zone temperature)
hw.sensors.acpithinkpad0.temp0=75.00 degC
hw.sensors.acpithinkpad0.temp1=0.00 degC
hw.sensors.acpithinkpad0.temp2=75.00 degC
hw.sensors.acpithinkpad0.temp3=0.00 degC
hw.sensors.acpithinkpad0.temp4=0.00 degC
hw.sensors.acpithinkpad0.temp5=0.00 degC
hw.sensors.acpithinkpad0.temp6=27.00 degC
hw.sensors.acpithinkpad0.temp7=0.00 degC
hw.sensors.km0.temp0=75.88 degC
hw.sensors.acpithinkpad0.fan0=441 RPM
> ("93C" is just a typical value, I've seen any between 92 and 98). I
> usually have just the time to log in before the system logs me out and
> shuts down. This laptop normally runs at around 80°C, and I think the
> temperature reading in OpenBSD is correct, because I get similar
> warnings
> and temperature values when I reboot immediately into another OS.
That may be a hint that something may be wrong
with your cooling. Dust blockage, etc.
> Booting on 5.6 bsd.rd and upgrading the system went fine, but as soon as
> I restarted the system, the same situation happened. Feeling
> adventurous,
> I tried to disable acpitz* during the boot process, which made the
> messages
> go away. The system ran just below 100°C (as reported by sysctl) for
> some time without any problem, until I didn't want to take the risk for
> any longer and shut it down manually. I also have an x100e from the same
> brand, quite similar even if older and slower, which does _NOT_ show the
> same symptoms. I'm attaching the dmesg and sysctl hw.sensors output of
> both
> machines running 5.6.
>
> Has anyone been running 5.5 and 5.6 on a x120e? Any clues on what I
> should
> do to diagnose the problem any better?
As I say, I never have had this issue with x120e, which I've
been using for over 3 years with OpenBSD, mainly following
snapshots.
Running older snapshot atm:
$ sysctl kern.version
kern.version=OpenBSD 5.6-current (GENERIC.MP) #368: Tue Sep 9 00:28:20 MDT 2014
t...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
I have a Gateway LT31 (?) that used to have similar issue as
you describe. After first cold boot, it would immediately
shutdown because of temperature warning. Next boot, it
would be fine.
However, since the last snapshot I put on it, from Sep. It
hasn't exhibited this behavior. Then again, the Gateway isn't
used much; so it could be that I've been lucky.
--patrick
>
> Cheers!
>
> --
> Étienne
> OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
> dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 1861025792 (1774MB)
> avail mem = 1802760192 (1719MB)
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xf09b0 (43 entries)
> bios0: vendor LENOVO version "6XET45WW (1.28 )" date 09/17/2010
> bios0: LENOVO 35089CU
> acpi0 at bios0: rev 2
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP TCPA SSDT APIC MCFG HPET SLIC
> acpi0: wakeup devices PB5_(S5) OHC0(S3) OHC1(S3) OHC2(S3) OHC3(S3) OHC4(S3)
> P2P_(S5) LID_(S3)
> acpitimer0 at acpi0: 3579545 Hz, 32 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: AMD Athlon(tm) Neo X2 Dual Core Processor L335, 1597.30 MHz
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
> cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 256KB
> 64b/line 16-way L2 cache
> cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully
> associative
> cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully
> associative
> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> cpu0: apic clock running at 199MHz
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: AMD Athlon(tm) Neo X2 Dual Core Processor L335, 1596.00 MHz
> cpu1:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,3DNOWP
> cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 256KB
> 64b/line 16-way L2 cache
> cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully
> associative
> cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully
> associative
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
> acpimcfg0 at acpi0 addr 0xe0000000, bus 0-3
> acpihpet0 at acpi0: 14318180 Hz
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus 2 (PB5_)
> acpiprt2 at acpi0: bus 4 (P2P_)
> acpiprt3 at acpi0: bus 1 (AGP_)
> acpiec0 at acpi0
> acpicpu0 at acpi0: C3, C2, PSS
> acpicpu1 at acpi0: PSS
> acpitz0 at acpi0: critical temperature is 92 degC
> acpibtn0 at acpi0: PWRB
> acpibtn1 at acpi0: SLPB
> acpithinkpad0 at acpi0
> acpiac0 at acpi0: AC unit online
> acpibat0 at acpi0: BAT1 model "42T4787" serial 626 oem "SONY"
> acpibtn2 at acpi0: LID_
> cpu0: PowerNow! K8 1597 MHz: speeds: 1600 800 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "AMD RS780 Host" rev 0x00
> ppb0 at pci0 dev 1 function 0 "AMD RS780 PCIE" rev 0x00
> pci1 at ppb0 bus 1
> radeondrm0 at pci1 dev 5 function 0 "ATI Radeon HD 3200" rev 0x00
> drm0 at radeondrm0
> radeondrm0: apic 2 int 18
> ppb1 at pci0 dev 5 function 0 "AMD RS780 PCIE" rev 0x00: msi
> pci2 at ppb1 bus 2
> re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x03: RTL8168D/8111D
> (0x2800), msi, address c8:0a:a9:6a:6c:6b
> rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
> ppb2 at pci0 dev 6 function 0 "AMD RS780 PCIE" rev 0x00: msi
> pci3 at ppb2 bus 3
> "Realtek 8192SE" rev 0x10 at pci3 dev 0 function 0 not configured
> ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: apic 2 int 22,
> AHCI 1.1
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, ST9250315AS, 0020> SCSI3 0/direct fixed
> naa.5000c50022882f8c
> sd0: 238475MB, 512 bytes/sector, 488397168 sectors
> ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16,
> version 1.0, legacy support
> ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16,
> version 1.0, legacy support
> ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> version 1.0, legacy support
> ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x3c: SMI
> iic0 at piixpm0
> spdmem0 at iic0 addr 0x51: 2GB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM
> azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int
> 16
> azalia0: codecs: Conexant/0x5066
> audio0 at azalia0
> pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x00
> ppb3 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
> pci4 at ppb3 bus 4
> pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
> pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
> pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
> kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev
> BH-G2
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> usb3 at ohci1: USB revision 1.0
> uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> usb4 at ohci2: USB revision 1.0
> uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> pms0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> wsmouse1 at pms0 mux 0
> pms0: Synaptics touchpad, firmware 7.4
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> umass0 at uhub1 port 1 configuration 1 interface 0 "Generic USB2.0-CRW" rev
> 2.00/58.88 addr 2
> umass0: using SCSI over Bulk-Only
> scsibus2 at umass0: 2 targets, initiator 0
> sd1 at scsibus2 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct
> removable serial.0bda0158114173400000
> uvideo0 at uhub1 port 2 configuration 1 interface 0 "Image Processor
> Integrated Camera" rev 2.00/30.08 addr 3
> video0 at uvideo0
> vscsi0 at root
> scsibus3 at vscsi0: 256 targets
> softraid0 at root
> scsibus4 at softraid0: 256 targets
> root on sd0a (cf86459bc41d995b.a) swap on sd0b dump on sd0b
> drm: initializing kernel modesetting (RS780 0x1002:0x9612 0x17AA:0x21B2).
> radeondrm0: VRAM: 336M 0x00000000C0000000 - 0x00000000D4FFFFFF (336M used)
> radeondrm0: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
> drm: PCIE GART of 512M enabled (table at 0x00000000C0040000).
> radeondrm0: 1366x768
> wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
> wskbd0
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> hw.sensors.acpitz0.temp0=47.00 degC (zone temperature)
> hw.sensors.acpithinkpad0.temp0=0.00 degC
> hw.sensors.acpithinkpad0.temp1=47.00 degC
> hw.sensors.acpithinkpad0.temp2=0.00 degC
> hw.sensors.acpithinkpad0.temp3=0.00 degC
> hw.sensors.acpithinkpad0.temp4=0.00 degC
> hw.sensors.acpithinkpad0.temp5=0.00 degC
> hw.sensors.acpithinkpad0.temp6=0.00 degC
> hw.sensors.acpithinkpad0.temp7=0.00 degC
> hw.sensors.acpithinkpad0.fan0=467 RPM
> hw.sensors.acpiac0.indicator0=On (power supply)
> hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
> hw.sensors.acpibat0.volt1=0.00 VDC (current voltage)
> hw.sensors.acpibat0.power0=0.00 W (rate)
> hw.sensors.acpibat0.watthour0=15.33 Wh (last full capacity)
> hw.sensors.acpibat0.watthour1=2.81 Wh (warning capacity)
> hw.sensors.acpibat0.watthour2=0.56 Wh (low capacity)
> hw.sensors.acpibat0.watthour3=0.00 Wh (remaining capacity), CRITICAL
> hw.sensors.acpibat0.watthour4=56.16 Wh (design capacity)
> hw.sensors.acpibat0.raw0=0 (battery idle), OK
> hw.sensors.acpibtn2.indicator0=On (lid open)
> hw.sensors.kate0.temp0=47.25 degC
> hw.sensors.kate0.temp1=45.75 degC
> hw.sensors.kate0.temp2=54.00 degC
> hw.sensors.kate0.temp3=51.00 degC
> OpenBSD 5.6 (GENERIC.MP) #333: Fri Aug 8 00:20:21 MDT 2014
> dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 3850960896 (3672MB)
> avail mem = 3739664384 (3566MB)
> User Kernel Config
> UKC> disable acpitz
> 368 acpitz* disabled
> UKC> exit
> Continuing...
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xf9ba0 (58 entries)
> bios0: vendor LENOVO version "8FET32WW (1.16 )" date 11/03/2011
> bios0: LENOVO 0596A28
> acpi0 at bios0: rev 2
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP SLIC HPET APIC MCFG UEFI UEFI SSDT SSDT UEFI
> acpi0: wakeup devices PB4_(S4) PB5_(S4) PB6_(S4) PB7_(S4) OHC1(S3) OHC2(S3)
> EHC2(S3) OHC3(S3) EHC3(S3) OHC4(S3) SBAZ(S4) GEC_(S4) P2P_(S5) SPB0(S4)
> SPB1(S4) SPB2(S4) [...]
> acpitimer0 at acpi0: 3579545 Hz, 32 bits
> acpihpet0 at acpi0: 14318180 Hz
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: AMD E-350 Processor, 6706.74 MHz
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,PAGE1GB,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
> cpu0: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
> 64b/line 16-way L2 cache
> cpu0: 8 4MB entries fully associative
> cpu0: DTLB 40 4KB entries fully associative, 8 4MB entries fully
> associative
> cpu0: smt 0, core 0, package 0
> mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
> cpu0: apic clock running at 199MHz
> cpu0: mwait min=64, max=64, C-substates=0.0.0.0.0, IBE
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: AMD E-350 Processor, 1596.60 MHz
> cpu1:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,PAGE1GB,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
> cpu1: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
> 64b/line 16-way L2 cache
> cpu1: 8 4MB entries fully associative
> cpu1: DTLB 40 4KB entries fully associative, 8 4MB entries fully
> associative
> cpu1: smt 0, core 1, package 0
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 21, 24 pins
> ioapic0: misconfigured as apic 0, remapped to apid 2
> acpimcfg0 at acpi0 addr 0xf8000000, bus 0-31
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus -1 (PB4_)
> acpiprt2 at acpi0: bus -1 (PB5_)
> acpiprt3 at acpi0: bus 1 (PB6_)
> acpiprt4 at acpi0: bus -1 (PB7_)
> acpiprt5 at acpi0: bus 2 (P2P_)
> acpiprt6 at acpi0: bus 3 (SPB0)
> acpiprt7 at acpi0: bus 4 (SPB1)
> acpiprt8 at acpi0: bus -1 (SPB2)
> acpiprt9 at acpi0: bus -1 (SPB3)
> acpiec0 at acpi0
> acpicpu0 at acpi0: C2, PSS
> acpicpu1 at acpi0: C2, PSS
> acpitz at acpi0 not configured
> acpibtn0 at acpi0: PWRB
> acpibtn1 at acpi0: SLPB
> acpithinkpad0 at acpi0
> acpiac0 at acpi0: AC unit online
> acpibat0 at acpi0: BAT1 model "42T4787" serial 2692 type LION oem "SONY"
> acpibtn2 at acpi0: LID_
> cpu0: 6706 MHz: speeds: 1600 1280 800 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
> radeondrm0 at pci0 dev 1 function 0 "ATI Radeon HD 6310" rev 0x00
> drm0 at radeondrm0
> radeondrm0: msi
> azalia0 at pci0 dev 1 function 1 "ATI Radeon HD 6310 HD Audio" rev 0x00:
> msi
> azalia0: no supported codecs
> ppb0 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00: msi
> pci1 at ppb0 bus 1
> re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x03: RTL8168D/8111D
> (0x2800), msi, address 04:7d:7b:3d:9c:5f
> rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
> ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: apic 2 int 19,
> AHCI 1.2
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, ST9500423AS, 0001> SCSI3 0/direct fixed
> naa.5000c50038ba9b3e
> sd0: 476940MB, 512 bytes/sector, 976773168 sectors
> ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> version 1.0, legacy support
> ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18,
> version 1.0, legacy support
> ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
> piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x42: polling
> iic0 at piixpm0
> spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-8500 SO-DIMM
> azalia1 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x40: apic 2 int
> 16
> azalia1: codecs: Conexant/0x5066
> audio0 at azalia1
> pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x40
> ppb1 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
> pci2 at ppb1 bus 2
> ppb2 at pci0 dev 21 function 0 "ATI SB800 PCIE" rev 0x00
> pci3 at ppb2 bus 3
> ppb3 at pci0 dev 21 function 1 "ATI SB800 PCIE" rev 0x00: msi
> pci4 at ppb3 bus 4
> "Realtek 8188CE" rev 0x01 at pci4 dev 0 function 0 not configured
> pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
> pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
> pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
> km0 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
> pchb4 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
> pchb5 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
> pchb6 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
> pchb7 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
> usb2 at ohci0: USB revision 1.0
> uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> usb3 at ohci1: USB revision 1.0
> uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> pms0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> wsmouse1 at pms0 mux 0
> pms0: Synaptics touchpad, firmware 7.5
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> uvideo0 at uhub1 port 5 configuration 1 interface 0 "Image Processor
> Integrated Camera" rev 2.00/30.08 addr 2
> video0 at uvideo0
> ugen0 at uhub2 port 4 "Broadcom Corp Broadcom Bluetooth Device" rev
> 2.00/7.48 addr 2
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on sd0a (dbbd96bdfb0cefb8.a) swap on sd0b dump on sd0b
> drm: initializing kernel modesetting (PALM 0x1002:0x9802 0x17AA:0x21DF).
> radeondrm0: VRAM: 384M 0x0000000000000000 - 0x0000000017FFFFFF (384M used)
> radeondrm0: GTT: 512M 0x0000000018000000 - 0x0000000037FFFFFF
> drm: PCIE GART of 512M enabled (table at 0x0000000000040000).
> drm: Internal thermal controller without fan control
> radeondrm0: 1366x768
> wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
> wskbd0
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> hw.sensors.acpithinkpad0.temp0=99.00 degC
> hw.sensors.acpithinkpad0.temp1=0.00 degC
> hw.sensors.acpithinkpad0.temp2=99.00 degC
> hw.sensors.acpithinkpad0.temp3=0.00 degC
> hw.sensors.acpithinkpad0.temp4=0.00 degC
> hw.sensors.acpithinkpad0.temp5=0.00 degC
> hw.sensors.acpithinkpad0.temp6=36.00 degC
> hw.sensors.acpithinkpad0.temp7=0.00 degC
> hw.sensors.acpithinkpad0.fan0=379 RPM
> hw.sensors.acpiac0.indicator0=On (power supply)
> hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
> hw.sensors.acpibat0.volt1=12.16 VDC (current voltage)
> hw.sensors.acpibat0.power0=0.00 W (rate)
> hw.sensors.acpibat0.watthour0=48.06 Wh (last full capacity)
> hw.sensors.acpibat0.watthour1=2.53 Wh (warning capacity)
> hw.sensors.acpibat0.watthour2=0.51 Wh (low capacity)
> hw.sensors.acpibat0.watthour3=42.35 Wh (remaining capacity), OK
> hw.sensors.acpibat0.watthour4=50.54 Wh (design capacity)
> hw.sensors.acpibat0.raw0=2 (battery charging), OK
> hw.sensors.acpibtn2.indicator0=On (lid open)
> hw.sensors.km0.temp0=99.50 degC
