I failed to include the new dmesg in the last email
User Kernel Config
UKC> chang wd
53 wd* at wdc0|wdc1|wdc*|wdc*|pciide*|pciide* channel -1 flags 0x0
change (y/n) ? y
channel [-1] ?
flags [0] ? 0x0ff0
53 wd* changed
53 wd* at wdc0|wdc1|wdc*|wdc*|pciide*|pciide* channel -1 flags 0xff0
UKC> quit
Continuing...
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: PC BIOS, date //
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xe0000/0x10000!
cpu0 at mainbus0: (uniprocessor)
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x04
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xf8000000, size 0x2400000
ppb0 at pci0 dev 1 function 0 "Intel 82815 AGP" rev 0x04
pci1 at ppb0 bus 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x05
pci2 at ppb1 bus 2
ubsec0 at pci2 dev 0 function 0 "Broadcom 5823" rev 0x01: 3DES MD5 SHA1
AES RNG PK, irq 10
cbb0 at pci2 dev 1 function 0 "TI PCI1520 CardBus" rev 0x01: irq 11,
CardBus support disabled
cbb1 at pci2 dev 1 function 1 "TI PCI1520 CardBus" rev 0x01: irq 11,
CardBus support disabled
fxp0 at pci2 dev 2 function 0 "Intel 82559ER" rev 0x10, i82551: irq 5,
address 00:00:00:00:00:00
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci2 dev 3 function 0 "Intel 82559ER" rev 0x10, i82551: irq 6,
address 00:00:00:00:00:00
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
fxp2 at pci2 dev 4 function 0 "Intel 82559ER" rev 0x10, i82551: irq 7,
address 00:00:00:00:00:00
inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4
fxp3 at pci2 dev 5 function 0 "Intel 82559ER" rev 0x10, i82551: irq 9,
address 00:00:00:00:00:00
inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4
cbb0: bad Vcc request. sock_ctrl 0x400, sock_status 0x30000206
cardslot0 at cbb0 slot 0 flags 0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x05: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x05: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFHNJC-008G>
wd0: 1-sector PIO, LBA48, 7629MB, 15625216 sectors
wd1 at pciide0 channel 0 drive 1: <FUJITSU MHV2040AS>
wd1: 16-sector PIO, LBA, 38154MB, 78140160 sectors
wd0(pciide0:0:0): using PIO mode 4
wd1(pciide0:0:1): using PIO mode 4
pciide0: channel 1 disabled (no drives)
ichiic0 at pci0 dev 31 function 3 "Intel 82801BA SMBus" rev 0x05: irq 9
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 256MB SDRAM non-parity PC133CL2
spdmem1 at iic0 addr 0x51: 256MB SDRAM non-parity PC133CL2
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4: polled
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio0 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
nvram: invalid checksum
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0a (511531c0c5c7c075.a) swap on wd0b dump on wd0b
clock: unknown CMOS layout
Thanks again for the help.
Stan
